• Operating voltage [V]: 12
• Rated Power [W]: 480
• Rated current [A]: 40
• Combi Switch Function: Normally Open Contact
• Number of pins: 4
• Manufacturer: JP GROUP
• Lisainfo: Relay, 12 Volt, 40 Amp
• Additional information: Relay, 12 Volt, 40 Amp

Relay function: Terminal 75, Interior Blower, Suction pipe pre-heating, Sunroof, Pump, fuel pre-supply, Start-stop system, Magnetic clutch, Surge protection, Battery main switch, Engine control unit, Normally open contact, X contact relief, Fan, engine cooling, Electric booster heater, Secondary Air System, Water pump after-run, Rear Window Wiper, heater/air conditioning, Clamp 15, Fuel Pump, Window Regulator, Heated windscreen, Heated rear window, Parking Heater

• Number of connectors: 4

Lisainfo: Relay for fuel pump and intake manifold heating, 12 Volt, 40 Amp Additional information: Relay for fuel pump and intake manifold heating, 12 Volt, 40 Amp

• Operating voltage [V]: 12
• Rated Power [W]: 120
• Rated current [A]: 10
• Combi Switch Function: Normally Open Contact
• Length [mm]: 30
• Width [mm]: 30
• Height [mm]: 42
• Connector type: 1x 2,8 mm, 5x 6,3 mm
• Number of pins: 6
• Lisainfo: Relay for wiper/washer
• Additional information: Relay for wiper/washer

• Rated Voltage [V]: 12
• Rated current [A]: 30
• Supplementary Article/Supplementary Info: without holder
• Number of pins: 5
• Temperature range from [°C]: -40
• Temperature range to [°C]: 100
• Housing Type: Synthetic Material Housing
• General Information: relay
• Manufacturer: VIKA

Combi Switch Function: without light dimmer function, Normally Open Contact

• for relay slot number: 3
• Relay Number: 395, 404, 646
• Rated Voltage [V]: 12
• Current Strength [A]: 10
• Relay function: Normally open contact
• Number of pins: 9
• Manufacturer: TOPRAN HANS PRIES

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Number of connectors: 4
• Rated Voltage [V]: 12
• Rated current [A]: 40
• Temperature range from [°C]: -40
• Temperature range to [°C]: 85
• General Information: relay
• Manufacturer: VIKA

• Ühenduste arv: 4
• Manufacturer: YSPARTS

• for relay slot number: 8
• Relay Number: 167
• Rated Voltage [V]: 12
• Current Strength [A]: 40
• Number of pins: 5
• Name: RELEE, KšTUSEPUMP
• Manufacturer: HAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• for relay slot number: 10
• Relay Number: 109
• Rated Voltage [V]: 12
• Number of pins: 4
• Relay function: Engine control unit
• Name: Relee, Ktusepump
• Manufacturer: HAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Quantity: 1
• Weight [kg]: 0.035
• Required quantity: 1
• Number of connectors: 4
• General Information: fuel pump relay
• Manufacturer: VIKA

• Rated Voltage [V]: 12
• Relay function: Pre-glow device
• Manufacturer: JP GROUP A/S
• Lisainfo: Relay, glowing, 12 Volt, 70 Amp
• Additional information: Relay, glowing, 12 Volt, 70 Amp

• Voltage [V]: 12
• Number of pins: 4
• Capacity at 12V: 40A
• Manufacturer: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Rated Voltage [V]: 12
• Rated current [A]: 70
• Temperature range from [°C]: -40
• Temperature range to [°C]: 85
• General Information: relay
• Manufacturer: VIKA

• Outer/Inner Mirror: for electric mirror adjustment
• Relay function: Daytime Running Light
• Combi Switch Function: Changeover Contact
• Name: Mitme funktsiooniga relee
• Manufacturer: MAX

• Construction Year to: 08.2002
• for OE number: 4H0 951 253 C
• Current Strength [A]: 30
• Voltage [V]: 12
• Number of pins: 5
• Relay function: Normally open contact
• Protection Type (IP Code): IP5K4
• Temperature range from [°C]: -40
• Temperature range to [°C]: 100
• Resistor [Ohm]: 16
• Name: JUHTSEADE,HOOGEAEG
• Manufacturer: BOS

• Current Strength [A]: 10
• Fitting Position: Vehicle Windscreen
• Voltage [V]: 12
• Lisainfo: Relay for wiper and washer, front, 12 Volt, 10 Amp
• Additional information: Relay for wiper and washer, front, 12 Volt, 10 Amp

Vehicle Equipment: for vehicles without controllable windscreen wiper intervals, for vehicles without rain sensor

• Name: RELEE, KšTUSEPUMP
• Manufacturer: MAX

• General Information: fuel pump relay
• Manufacturer: VIKA

• Relay function: Sunroof
• Combi Switch Function: Normally Open Contact
• Voltage [V]: 12
• Name: Mitme funktsiooniga relee
• Manufacturer: MAX

• Operating voltage [V]: 12
• Rated Power [W]: 180
• Rated current [A]: 15
• Combi Switch Function: Normally Open Contact
• Resistor [Ohm]: 70
• Number of pins: 4
• Manufacturer: JP GROUP
• Lisainfo: Multifunctional Relay
• Additional information: Multifunctional Relay

Relay function: Sunroof, Fuel Pump, Tailgate, Terminal 30, Gear Lever, Licence plate light, Engine control unit, Normally open contact

• Voltage [V]: 12
• Rated current [A]: 40
• Number of pins: 4
• Combi Switch Function: Normally Open Contact
• Manufacturer: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Quantity: 1
• Rated Voltage [V]: 12
• Relay function: Pre-glow device
• General Information: control unit for glow plug relay
• Manufacturer: VIKA

• for relay slot number: 8
• Relay Number: 103
• Voltage [V]: 12
• Name: RELEE, HOOGSšSTEEM
• Manufacturer: MAX

• Number of pins: 4
• Rated current [A]: 15
• Resistor [Ohm]: 70
• Combi Switch Function: Normally Open Contact
• for OE number: 357906381A
• Manufacturer: DELLO AUTOMEGA

Relay function: Fuel Pump, Engine control unit, Terminal 30, Sunroof, Tailgate, Licence plate light, Gear Lever

• Outer/Inner Mirror: for electric mirror adjustment
• Operating voltage [V]: 12
• Rated current [A]: 20, 40
• Combi Switch Function: Changeover Contact
• Temperature range from [°C]: -40
• Temperature range to [°C]: 85
• Resistor [Ohm]: 680
• Length [mm]: 23
• Width [mm]: 15
• Height [mm]: 26
• Connector type: 3x 4,8 mm, 2x 6,3 mm
• Number of pins: 5
• Name: MITME FUNKTSIOONIGA RELEE
• Manufacturer: MEY
• Lisainfo: 1148300001
• Additional information: 1148300001

Relay function: Terminal 50, Terminal 75, Heated windscreen, Remote Lock, boot-/ loading bay hatch, Low Beam, Heated rear window, Surge protection, Normally open contact, Daytime Running Light, Cigarette Lighter, Electric booster heater, Washer Fluid Pump, windscreen, headlight cleaning, Interior Blower, Auxiliary Water Pump, Starter, Parking Light, Clamp 15, Klaxon, Trumpet Horns, Engine control unit

• for OE number: 004 545 2905
• Current Strength [A]: 20
• Number of connectors: 5
• Relay function: Normally open contact
• Voltage [V]: 12
• Name: MITME FUNKTSIOONIGA RELEE
• Manufacturer: TRU

• Relay Number: 53
• Voltage [V]: 12
• Capacity at 12V: 40A
• Combi Switch Function: Normally Open Contact
• Number of pins: 4
• Temperature range from [°C]: -40
• Temperature range to [°C]: 125
• Weight [g]: 24
• Inductive Load [A]: 15
• Capacitive Load [A]: 5
• Rated current [A]: 40
• Ohmic Load [A]: 40
• Quantity: 1
• Assy./disassy. by qualified personnel required!:
• Manufacturer: HELLA
• Name: HE 4RA933332451

Relay function: Comfort Equipment Variant (trim package), park distance control, ABS, Low Beam, High Beam, Heated rear window, ESP, Window Regulator, Starter, Klaxon, Air Conditioning, Light switch, Fan, heater/air conditioning, Interior Blower, Clamp 15, Daytime Running Light, Convertible Top Hydraulics, Central Locking, ABS recovery pump, Exterior Rearview Mirror Adjustment, Heatable exterior mirror, Electric booster heater, Interior Lighting, Clamp 15R, Clamp 87, Fuel Pump, Oxygen Sensor, engine cooling, Front Fog Light, Windscreen Wiper, Windscreen Wiper Rest Heating, Sunroof, Secondary Air System, Seat Heating Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Voltage [V]: 12
• Weight [kg]: 0.025
• Number of connectors: 4
• Current Strength [A]: 30
• Supplementary Article/Supplementary Info: with holder
• General Information: relay
• Manufacturer: BORSEHUNG

• Vehicle Equipment: for vehicles without trailer hitch
• Operating Mode: Electronic
• Voltage [V]: 12
• Manufacturer: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Relay function: Pre-glow device, X contact relief
• Rated Voltage [V]: 12
• Number of connectors: 4
• Current Strength [A]: 70
• Relay Number: 644
• General Information: relay
• Manufacturer: BORSEHUNG

• General Information: relay
• Manufacturer: BORSEHUNG

• for relay slot number: 10
• Relay Number: 109
• Number of pins: 4
• Relay function: Engine control unit
• Name: RELEE, KšTUSEPUMP
• Manufacturer: MAX

• General Information: relay
• Manufacturer: BORSEHUNG

• General Information: relay
• Manufacturer: BORSEHUNG

• Guarantee: 3 years guarantee
• Weight [kg]: 0.04
• Always compare old and new part (in particular OE No.):
• Name: CE 96SKV005
• Manufacturer: ESEN SKV

• General Information: relay
• Manufacturer: BORSEHUNG

• Vehicle Equipment: for vehicles without trailer hitch
• Relay Number: 21, 191
• Voltage [V]: 12
• Rated Power [W]: 21
• Number of connectors: 3
• Colour: black
• Material: Plastic
• Operating Mode: Electronic
• Weight [kg]: 0.032
• Name: SUUNATULEDE LšLITI
• Manufacturer: FEB

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Voltage [V]: 12
• Number of pins: 6
• Name: RELEE,KOJAMEHED-PESU-INTERVALL
• Manufacturer: MAX

• Relay Number: 67, 80, 167
• Number of connectors: 4
• Weight [kg]: 0.035
• Name: RELEE, KšTUSEPUMP
• Manufacturer: FEB

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Outer/Inner Mirror: for electric mirror adjustment
• Combi Switch Function: Changeover Contact
• Relay function: Normally open contact
• Manufacturer: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Operating voltage [V]: 12
• Rated Power [W]: 480
• Rated current [A]: 40
• Combi Switch Function: Normally Open Contact
• Length [mm]: 28
• Width [mm]: 28
• Height [mm]: 25
• Connector type: 2x 6,3 mm, 2x 9,5 mm
• Number of pins: 4
• Name: MITME FUNKTSIOONIGA RELEE
• Manufacturer: MEY

Relay function: Fuel Pump, Engine control unit, Surge protection, Suction pipe pre-heating, Interior Blower, Heated rear window, Battery main switch, Heated windscreen, Fan, heater/air conditioning, Rear Window Wiper, Water pump after-run, Secondary Air System, Electric booster heater, engine cooling, Normally open contact, Clamp 15, Parking Heater, X contact relief, Window Regulator, Sunroof, Pump, fuel pre-supply, Terminal 75, Start-stop system, Magnetic clutch

• Number of pins: 4
• Voltage [V]: 12
• Rated current [A]: 15
• Combi Switch Function: Normally Open Contact
• Manufacturer: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Vehicle Equipment: for vehicles without rain sensor
• Rated Voltage [V]: 12
• Supplementary Article/Info 2: for windscreen cleaning
• Name: RELEE,KOJAMEHED-PESU-INTERVALL
• Manufacturer: HAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Operating voltage [V]: 12
• Rated current [A]: 40
• Combi Switch Function: Normally Open Contact
• Length [mm]: 28
• Width [mm]: 28
• Height [mm]: 24.5
• Connector type: 1x 6,3 mm, 2x 9,5 mm, 1x 2,8 mm
• Number of pins: 4
• Name: MITME FUNKTSIOONIGA RELEE
• Manufacturer: MEY

Relay function: Fuel Pump, Exterior Rearview Mirror Adjustment, Normally open contact, Fan, engine cooling, Suction pipe pre-heating

• for OE number: 191 906 383 C
• Number of connectors: 4
• Relay function: Normally open contact
• Rated current [A]: 40
• Voltage [V]: 12
• Manufacturer: TRUCKTEC

• Outer/Inner Mirror: for electric mirror adjustment
• Operating voltage [V]: 12
• Rated current [A]: 10, 30
• Combi Switch Function: Changeover Contact
• Temperature range from [°C]: -40
• Temperature range to [°C]: 120
• Resistor [Ohm]: 560
• Length [mm]: 23
• Width [mm]: 15
• Height [mm]: 26
• Connector type: 2x 6,3 mm, 3x 4,8 mm
• Number of pins: 5
• Name: MITME FUNKTSIOONIGA RELEE
• Manufacturer: MEY

Relay function: Electric booster heater, Normally open contact, Fuel Filler Cap, Trumpet Horns, Seat Heating, Indicator, Daytime Running Light, Air Conditioning, Parking Heater, Central Locking, Window Regulator, Trailer stop light, Exterior Rearview Mirror Adjustment, Hinged Window, Heatable exterior mirror, Washer Fluid Pump, windscreen, Terminal 50, Water pump after-run, Roof ventilation, Terminal 61, Auxiliary Water Pump, Fan, engine cooling, headlight cleaning

• Construction Year to: 08.2002
• for OE number: 2D0 959 145 A
• Current Strength [A]: 15
• Voltage [V]: 12
• Relay function: Normally open contact
• Manufacturer: BOSCH

• Weight [kg]: 0.035
• Fitting Position: Engine Compartment
• Manufacturer: VEMO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Vehicle Identification Number (VIN) from: 6K-X-400 000
• Vehicle Identification Number (VIN) to: 6K-X-499 999
• Current Strength [A]: 15
• Relay function: Terminal 30, Clamp 87
• Number of pins: 4
• Voltage [V]: 12
• Colour: black
• Weight [kg]: 0.033
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Operating voltage [V]: 12
• Rated Power [W]: 180
• Rated current [A]: 15
• Combi Switch Function: Normally Open Contact
• Temperature range to [°C]: -40
• Resistor [Ohm]: 70
• Length [mm]: 30
• Width [mm]: 30
• Height [mm]: 30
• Connector type: 3x 6,3 mm, 1x 2,8 mm
• Number of pins: 4
• Name: MITME FUNKTSIOONIGA RELEE
• Manufacturer: MEY

Relay function: Engine control unit, Normally open contact, Fuel Pump, Gear Lever, Sunroof, Tailgate, Licence plate light, Terminal 30

• Weight [kg]: 0.04
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Pinge [V]: 12
• Relee funktsioon: Töökontakt
• OE-numbri jaoks: 8E0 951 253
• Garantii: 3 aastat garantii
• Korpuse materjal: Plastik
• Värv: must
• Rakendustüüp: elektriline
• Kaal (g): 24
• Manufacturer: AT AUTOTEILE GERMANY

Üldine informatsioon: Products and spare parts supplied by us are only intended for the designated use. Installation may only be carried out by trained specialist personnel. Our products are not always supplied with installation instructions. Improper installation or inappropriate use may lead to the exclusion of warranty.

• Construction Year to: 08.2002
• for OE number: 8E0 951 253
• Combi Switch Function: On/Off Switch
• Current Strength [A]: 70
• Voltage [V]: 12
• Number of pins: 4
• Relay function: Normally open contact
• Housing Type: Housing with Plastic Lid
• Protection Type (IP Code): IP20
• Temperature range from [°C]: -40
• Temperature range to [°C]: 85
• Housing Colour: black
• Resistor [Ohm]: 63
• Length [mm]: 28
• Width [mm]: 28
• Height [mm]: 40
• Manufacturer: BOSCH

• Voltage [V]: 12
• Current Strength [A]: 20
• Number of pins: 4
• for OE number: 857951253
• Manufacturer: MEAT&DORIA

• Construction Year to: 08.2002
• for OE number: 019 193 750 3
• Current Strength [A]: 70
• Voltage [V]: 12
• Number of pins: 4
• Relay function: Normally open contact
• Temperature range from [°C]: -40
• Temperature range to [°C]: 85
• Name: RELEE
• Manufacturer: BOS

• Fitting Position: engine sided
• Relay Number: 10/109
• Supplementary Article/Info 2: Mini Relay, with resistor
• Supplementary Article/Supplementary Info: without holder
• Protection Type (IP Code): IP54
• Voltage [V]: 12
• Temperature range from [°C]: -40
• Temperature range to [°C]: +70
• Colour: black
• Inductive Load [A]: 15
• Capacitive Load [A]: 15
• Ohmic Load [A]: 15
• Number of pins: 4
• Wiring Diagramme: X
• Combi Switch Function: Normally Open Contact
• Plug Type ID: X
• Assy./disassy. by qualified personnel required!:
• Name: HE 4RA007507081
• Manufacturer: HELLA

Relay function: Central electrics, Comfort Equipment Variant (trim package), park distance control, ABS, Low Beam, High Beam, Heated rear window, ESP, Window Regulator, Starter, Klaxon, Air Conditioning, Light switch, Fan, heater/air conditioning, Interior Blower, Clamp 15, Daytime Running Light, Convertible Top Hydraulics, Central Locking, ABS recovery pump, Exterior Rearview Mirror Adjustment, Heatable exterior mirror, Electric booster heater, Interior Lighting, Clamp 15R, Clamp 87, Fuel Pump, Oxygen Sensor, engine cooling, Front Fog Light, Windscreen Wiper, Windscreen Wiper Rest Heating, Sunroof, Secondary Air System, Seat Heating Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Voltage [V]: 12
• Capacity at 12V: 40A
• Colour: white
• Number of pins: 5
• Combi Switch Function: Normally Open Contact
• Assy./disassy. by qualified personnel required!:
• Manufacturer: HELLA
• Name: HE 4RA007507021

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Relay function: Normally open contact
• Voltage [V]: 12
• Current Strength [A]: 30
• Number of pins: 4
• Relay Number: 428
• Supplementary Article/Info 2: with resistor
• Housing Colour: grey
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Voltage [V]: 12
• Assy./disassy. by qualified personnel required!:
• Manufacturer: HELLA
• Name: HE 4RP008189151

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Guarantee: 5 years guarantee
• General Information: Sold in Hueco brand: printing and packaging
• Name: HU 132258
• Manufacturer: HUECO / HITACHI

• Number of pins: 10, 4
• Rated Voltage [V]: 12
• Housing material: Polyamid 6.6, GRP (Glass fibre Reinforced Plastic)
• Fabrication Number: CSW-VW-006
• Manufacturer: NTY
• Name: NTY CSW-VW-006

• Voltage [V]: 12
• Number of pins: 6
• Weight [kg]: 0.04
• Fitting Position: Engine Compartment
• Manufacturer: VEMO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Number of Cylinders: 5, 4
• Voltage [V]: 12
• Name: JUHTSEADE,HOOGEAEG
• Manufacturer: BER

• Supplementary Article/Supplementary Info: without holder
• Voltage [V]: 12
• Temperature range from [°C]: -30
• Temperature range to [°C]: +85
• Number of pins: 6
• Assy./disassy. by qualified personnel required!:
• Name: HE 5WG003620097
• Manufacturer: HELLA

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Guarantee: 3 years guarantee
• Always compare old and new part (in particular OE No.):
• Weight [kg]: 0.23
• Manufacturer: SKV GERMANY
• Name: CE 96SKV206

• Rated Voltage [V]: 12
• Number of pins: 10, 4
• Housing material: Polyamid 6.6, GRP (Glass fibre Reinforced Plastic)
• Name: PRZEKANIK WENTYLATORA VAG
• Manufacturer: HAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Supplementary Article/Supplementary Info: without holder
• Voltage [V]: 12
• Temperature range from [°C]: -30
• Temperature range to [°C]: +85
• Number of pins: 6
• Assy./disassy. by qualified personnel required!:
• Name: HE 5WG003620091
• Manufacturer: HELLA

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Vehicle Identification Number (VIN) from: 6K-X-000 001
• Vehicle Identification Number (VIN) to: 6K-X-399 999
• Voltage [V]: 12
• Weight [kg]: 0.038
• Fitting Position: Engine Compartment
• Manufacturer: VEMO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Engine Code: AGP
• Vehicle Equipment: for vehicles with automatic transmission
• Number of pins: 13
• Manufacturer: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Construction Year from: 09.2002
• Voltage [V]: 12
• Current Strength [A]: 60
• Number of connectors: 10
• Weight [kg]: 0.172
• Fitting Position: Engine Compartment
• Manufacturer: VEMO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Voltage [V]: 12
• Number of connectors: 13
• Weight [kg]: 0.178
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Construction Year to: 08.2002
• Voltage [V]: 12
• Relay function: Normally open contact
• Manufacturer: BOSCH