• Vehicle Identification Number (VIN) to: 6K-X-448 600
• Operating voltage [V]: 12
• Sensor Type: NTC Sensor
• Switch Point [°C]: 150
• Diameter [mm]: 20
• Number of pins: 4
• Manufacturer: JP GROUP A/S
• Lisainfo: Temperature sensor for cooling system, 4 pins
• Additional information: Temperature sensor for cooling system, 4 pins

• General Information: temperature sensor
• Manufacturer: VIKA

• Vehicle Equipment: for vehicles with air conditioning
• Number of pins: 2
• Switch Point [°C]: 119
• Lisainfo: Thermo switch for air condition 119 C
• Additional information: Thermo switch for air condition 119 C

• for OE number: 357919501A
• Manufacturer: KAMOKA

• Number of pins: 4
• Fitted Diameter [mm]: 20
• Supplementary Article/Info 2: with seal ring
• for OE number: 1331294
• Manufacturer: KAMOKA

• Temperature range to [°C]: 150
• for OE number: 59919501
• Manufacturer: KAMOKA

• Quantity: 1
• Weight [kg]: 0.041
• Number of connectors: 4
• Outer Diameter [mm]: 20
• Colour: yellow
• Colour Coding: blue
• Required quantity: 1
• General Information: temperature sensor; yellow
• Manufacturer: VIKA

• Housing Colour: white
• for OE number: 191 919 369 A S1
• Manufacturer: KAMOKA

• Quantity: 1
• Weight [kg]: 0.041
• Number of connectors: 4
• Outer Diameter [mm]: 20
• Colour: blue
• Colour Coding: blue
• Required quantity: 1
• General Information: temperature sensor; blue
• Manufacturer: VIKA

• Weight [kg]: 0.02
• Number of connectors: 4
• Outer Diameter [mm]: 20
• Plug Type ID: 4
• Colour: green
• Required quantity: 1
• General Information: temperature sensor; green; 4 pins
• Manufacturer: VIKA

• Supplementary Article/Supplementary Info: with gasket/seal
• Manufacturer: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Switch Point [°C]: 10
• Number of pins: 2
• Vehicle Equipment: for vehicles with air conditioning
• Lisainfo: Thermo switch for air condition 10/1.7 C
• Additional information: Thermo switch for air condition 10/1.7 C

• Connector Shape: oval
• Fabrication Number: ECP-AU-026
• Manufacturer: NTY

• for OE number: 1H0 919 563
• Width [mm]: 33
• Height [mm]: 30
• Length [mm]: 58
• Weight [g]: 25
• Guarantee: 3 years guarantee
• Manufacturer: AT AUTOTEILE GERMANY

General Information: Products and spare parts supplied by us are only intended for the designated use. Installation may only be carried out by trained specialist personnel. Our products are not always supplied with installation instructions. Improper installation or inappropriate use may lead to the exclusion of warranty.

• Number of pins: 3
• Supplementary Article/Info 2: with clip
• Guarantee: 3 years guarantee
• Weight [kg]: 0.1
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 17SKV550

• Housing Colour: black
• Number of pins: 4
• Spanner Size: 0
• Manufacturer: DELPHI
• Name: DE TS10236-12B1

Manufacturer: FAE

• Engine Code: 1Z
• Thread Size: M10x1
• Spanner Size: 13
• Corresponds to the original part in colour: white
• Name: EP 1.830.154
• Manufacturer: EPS

• Engine Code: 1Z
• Thread Size: M10x1
• Spanner Size: 13
• Corresponds to the original part in colour: white
• Manufacturer: FACET

• Thread Size: M10x1.0
• Manufacturer: VERNET

• Engine Code: AHU, 1Z
• new version:
• Outer Diameter [mm]: 20
• Number of connectors: 4
• Colour: black
• Colour Coding: blue
• Supplementary Article/Info 2: without seal ring
• Weight [kg]: 0.023
• Manufacturer: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Engine Code: AHU, 1Z
• new version:
• Outer Diameter [mm]: 20
• Number of connectors: 4
• Colour: black
• Colour Coding: blue
• Supplementary Article/Info 2: without seal ring
• Weight [kg]: 0.023
• Name: SW 30 93 0616
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Engine Code: ALH, AGR
• Vehicle Equipment: for vehicles with gearshift linkage
• for PR number: 0G3
• Number of connectors: 3
• Lisainfo: Distance sensor
• Additional information: Distance sensor

• Voltage [V]: 12
• Vehicle Equipment: for vehicles with gearshift linkage
• Number of pins: 3
• General Information: distance sensor
• Manufacturer: VIKA

• for OE number: 357 919 149
• Number of pins: 3
• Supplementary Article/Info 2: without cable
• Connector Shape: rectangular
• Fabrication Number: ECP-VW-002
• Manufacturer: NTY

Lisainfo: AUDI A2, A3, TT, FORD GALAXY, SEAT ALHAMBRA, AROSA, CORDOBA, IBIZA II, IBIZA III, IBIZA IV, INCA, LEON, TOLEDO I, TOLEDO II, SKODA FABIA I, OCTAVIA I 1.0-2.8 83- Additional information: AUDI A2, A3, TT, FORD GALAXY, SEAT ALHAMBRA, AROSA, CORDOBA, IBIZA II, IBIZA III, IBIZA IV, INCA, LEON, TOLEDO I, TOLEDO II, SKODA FABIA I, OCTAVIA I 1.0-2.8 83-

• for OE number: 357 919 149 B
• Overall Length [mm]: 78
• Fitting Depth [mm]: 32.5
• Supplementary Article/Info 2: without cable
• Connector Shape: D Shape
• Thread Size Entry: M16x1,5 mm
• Fabrication Number: ECP-AU-033
• Manufacturer: NTY

• Sensor Type: Inductive Sensor
• Number of pins: 3
• Cable Length [mm]: 521
• Manufacturer: ABAKUS LORO

General Information: The following information is for general and informational purposes only and does not constitute warranty terms. Warranty terms and conditions are available from our dealers and in our general terms and conditions of sale. Abakus spare/repair parts are intended only for vehicle repairs in order to restore their original functionality. Abakus spare/repair parts are used or sold to users only for the purpose of repairing vehicles to restore their original look and functionality and are not original/genuine/OE/OEM/OES replacement parts. These items do not originate from the vehicle manufacturer and may be the subject of a design not owned by Abakus. They may only be used for repairs to restore the intended vehicle to its original appearance. Our products are delivered without instruction of installation. Installation of our product may only be carried out by trained specialist technicians in specific car repairs. Products supplied by us are exclusively intended for proper and appropriate use. The warranty may become invalid in the event of: improper installation or repair, unsuitable application or use, installation or repair made outside specialist car workshops. Warranty claims are lost if the vehicle is modified and used for motor sports, tuning or similar events (except our tuning parts which are described in TecDoc and on our price list). Warranty application should include complete documentation among others: chassis no., first registration, vehicle mileage, information about LPG installation, fault memory log, pictures, our QC (quality check) code, installation invoice, contact details of the car repair workshop performing the replacement or repair. Warranty application are available in our Client Panel system. Complaints may require supplementing data such as error memory logs. Incomplete documentation may result in rejection of the claim. Any damage caused during transport is not considered quality damage and will be considered on an individual basis. The product is intended for use within the performance limits specified by the manufacturer and should only be used by qualified personnel who have been trained to operate this product. Before each use, the product should be checked for damage or fixing of its parts and not used if any defects or loose parts are found. Failure to follow the manufacturer's guidelines could result in potential product damage or even injury. Wear appropriate protective clothing if necessary when working with the product.

• Sensor Type: Passive sensor
• for OE number: 9118368
• Manufacturer: KAMOKA

• Colour: black
• Supplementary Article/Supplementary Info: with gasket/seal
• Manufacturer: METZGER

• Vehicle Identification Number (VIN) to: ******6K*X*448600
• Temperature range to [°C]: 150
• Outer Diameter [mm]: 20
• Number of connectors: 4
• Colour: green
• Weight [kg]: 0.2
• Supplementary Article/Supplementary Info: with gasket/seal, with retaining spring
• Name: SW 30 93 1539
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Connector Shape: rectangular
• Material: Brass
• Number of pins: 1
• Plug Type: Male
• Sensor Type: NTC Sensor
• Spanner Size: 14 mm
• Thread Size: M10x1,0
• Name: NI 207058
• Manufacturer: NISSENS

Technical Information: FIRST FIT - a time-saving installation! Find all additional parts such as O-rings, clip, washer in the box.

• for OE number: 357 919 501
• Weight [kg]: 0.025
• Supplementary Article/Supplementary Info: with gasket/seal
• Colour Coding: green
• Number of pins: 4
• Manufacturer: VEMO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• General Information: distance sensor
• Manufacturer: VIKA

• Vehicle Identification Number (VIN) to: ******6K*X*448600
• Temperature range to [°C]: 150
• Outer Diameter [mm]: 20
• Number of connectors: 4
• Weight [kg]: 0.2
• Supplementary Article/Supplementary Info: with gasket/seal, with retaining spring
• Manufacturer: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Sensor Type: NTC Sensor
• Mounting Type: Clamped
• Connector Shape: rectangular
• Number of pins: 4
• Socket colour: black
• for OE number: 357919501
• Supplementary Article/Info 2: with seal ring
• Manufacturer: NRF

• Number of pins: 3
• Supplementary Article/Info 2: without cable
• Connector Shape: D Shape
• Fabrication Number: ECP-AU-028

• Plug Type: Blade Terminal
• Operating Mode: Mechanical
• Number of pins: 2
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Vehicle Equipment: for vehicles with automatic climate control
• Number of pins: 2
• Connector Shape: rectangular, angled
• Mounting Type: Clipped
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Engine Code: 1Z
• Thread Size: M10 x 1
• Spanner Size: 13
• Supplementary Article/Supplementary Info: with gasket/seal
• Number of pins: 1
• Weight [kg]: 0.02
• Manufacturer: VEMO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Vehicle Equipment: for vehicles with gearshift linkage
• for PR number: 0G3
• Connector Shape: D Shape
• Number of Teeth: 15
• Number of pins: 3
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Engine Code: AHU, 1Z
• new version:
• Outer Diameter [mm]: 20
• Number of connectors: 4
• Colour: black
• Colour Coding: blue
• Weight [kg]: 0.026
• Supplementary Article/Supplementary Info: with retaining spring, with gasket/seal
• Manufacturer: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Number of pins: 4
• Supplementary Article/Info 2: with seal ring
• Colour: black
• Manufacturer: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• General Information: speedometer
• Manufacturer: VIKA

• Engine Code: 1Z; AHU
• Diameter [mm]: 25
• Length [mm]: 42
• Weight [kg]: 0.03
• Supplementary Article/Supplementary Info: with gasket/seal
• for OE number: 6U0 919 501 B
• Colour Coding: blue
• Number of pins: 4
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Switch Point [°C]: 140
• Outer Diameter [mm]: 20
• Weight [kg]: 0.023
• Number of connectors: 4
• Colour: black
• Colour Coding: yellow
• General Information: coolant temperature sensor
• Manufacturer: BORSEHUNG

• Engine Code: AHU, 1Z
• new version:
• Outer Diameter [mm]: 20
• Number of connectors: 4
• Colour: black
• Colour Coding: blue
• Weight [kg]: 0.026
• Supplementary Article/Supplementary Info: with retaining spring, with gasket/seal
• Name: SW 32 93 9142
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Vehicle Equipment: for vehicles with gearshift linkage
• Vehicle Identification Number (VIN) from: 6K-1-210001
• for PR number: 0G1
• Connector Shape: D Shape
• Number of pins: 3
• Supplementary Article/Info 2: without cable
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Sensor Type: Inductive Sensor
• Resistor [Ohm]: 540
• Number of pins: 3
• Cable Length [mm]: 1,000
• General Information: distance sensor
• Manufacturer: VIKA

• Engine Code: AGR, ALH, AHU, 1Z
• Vehicle Equipment: for vehicles with automatic climate control
• Block Separation:
• Vehicle Identification Number (VIN) from: ******6K*X*400001
• Number of connectors: 2
• Weight [kg]: 0.005
• for OE number: 1H0 907 543 A
• Manufacturer: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Number of pins: 3
• Supplementary Article/Info 2: without cable
• Connector Shape: rectangular
• Manufacturer: ABAKUS

General Information: The following information is for general and informational purposes only and does not constitute warranty terms. Warranty terms and conditions are available from our dealers and in our general terms and conditions of sale. Abakus spare/repair parts are intended only for vehicle repairs in order to restore their original functionality. Abakus spare/repair parts are used or sold to users only for the purpose of repairing vehicles to restore their original look and functionality and are not original/genuine/OE/OEM/OES replacement parts. These items do not originate from the vehicle manufacturer and may be the subject of a design not owned by Abakus. They may only be used for repairs to restore the intended vehicle to its original appearance. Our products are delivered without instruction of installation. Installation of our product may only be carried out by trained specialist technicians in specific car repairs. Products supplied by us are exclusively intended for proper and appropriate use. The warranty may become invalid in the event of: improper installation or repair, unsuitable application or use, installation or repair made outside specialist car workshops. Warranty claims are lost if the vehicle is modified and used for motor sports, tuning or similar events (except our tuning parts which are described in TecDoc and on our price list). Warranty application should include complete documentation among others: chassis no., first registration, vehicle mileage, information about LPG installation, fault memory log, pictures, our QC (quality check) code, installation invoice, contact details of the car repair workshop performing the replacement or repair. Warranty application are available in our Client Panel system. Complaints may require supplementing data such as error memory logs. Incomplete documentation may result in rejection of the claim. Any damage caused during transport is not considered quality damage and will be considered on an individual basis. The product is intended for use within the performance limits specified by the manufacturer and should only be used by qualified personnel who have been trained to operate this product. Before each use, the product should be checked for damage or fixing of its parts and not used if any defects or loose parts are found. Failure to follow the manufacturer's guidelines could result in potential product damage or even injury. Wear appropriate protective clothing if necessary when working with the product.

• Engine Code: ALH, AGR, AHU
• Cable Length [mm]: 540
• Number of connectors: 3
• Housing Colour: black
• Lisainfo: Sensor, crankshaft pulse
• Additional information: Sensor, crankshaft pulse

• Engine Code: ALH, AGR
• Vehicle Identification Number (VIN) from: 6K-Y-021 001
• Cable Length [mm]: 535
• Number of connectors: 3
• Housing Colour: black
• Lisainfo: Sensor, crankshaft pulse
• Additional information: Sensor, crankshaft pulse

• Connector Shape: rectangular
• Number of pins: 3
• General Information: distance sensor
• Manufacturer: VIKA

• Outer Diameter [mm]: 20
• Weight [kg]: 0.02
• Number of connectors: 4
• Colour: black
• Required quantity: 1
• General Information: coolant temperature sensor
• Manufacturer: BORSEHUNG

• Engine Code: AGR, ALH, AHU, 1Z
• Block Separation:
• Vehicle Identification Number (VIN) from: 6K-X-400 001
• Weight [kg]: 0.004
• Vehicle Equipment: for vehicles with automatic climate control
• Number of pins: 2
• Manufacturer: VEMO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Outer Diameter [mm]: 20
• Weight [kg]: 0.02
• Number of connectors: 4
• Colour: green
• Required quantity: 1
• General Information: coolant temperature sensor
• Manufacturer: BORSEHUNG

• Vehicle Equipment: for vehicles with gearshift linkage
• Vehicle Identification Number (VIN) to: 6K-1-210000
• for PR number: 0G1
• Connector Shape: rectangular
• Number of pins: 3
• Supplementary Article/Info 2: without cable
• for OE number: 357 919 149
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Engine Code: 1Z, AHU
• Block Separation:
• Cable Length [mm]: 500
• Sensor Type: Passive sensor
• for OE number: 1100749
• Manufacturer: KAMOKA

• Vehicle Identification Number (VIN) from: 6K-Y-021001
• Connector Shape: D Shape
• Number of pins: 3
• Supplementary Article/Info 2: with cable
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• General Information: interior temperature sensor
• Manufacturer: BORSEHUNG

• Engine Code: AGR, ALH
• Vehicle Identification Number (VIN) from: ******6K*1*210001
• Number of connectors: 3
• Weight [kg]: 0.024
• for OE number: 191 919 149 E
• Manufacturer: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Transmission Type: 4-Speed Automatic Transmission
• Alternatively:
• Number of pins: 2
• Supplementary Article/Info 2: with seal ring
• Weight [kg]: 0.018
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Number of pins: 1
• Weight [kg]: 0.3
• Packaging length [cm]: 12
• Packaging width [cm]: 8
• Packaging height [cm]: 6

• Vehicle Equipment: for vehicles with gear shift cable
• Vehicle Identification Number (VIN) from: 6K-1-210001
• for PR number: 0G4
• Number of pins: 3
• Connector Shape: D Shape
• Supplementary Article/Info 2: without cable
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Vehicle Equipment: for vehicles with gear shift cable
• Connector Shape: rectangular
• Number of pins: 3
• Supplementary Article/Info 2: without cable
• for OE number: 191 919 149D
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Housing Type: Aluminium Housing
• Height [mm]: 82
• Supplementary Article/Supplementary Info: with gasket/seal
• Fitting Depth [mm]: 54
• Fabrication Number: EPO-AU-000
• Manufacturer: NTY
• Name: NTY EPO-AU-000

• Engine Code: AGR
• Construction Year from: 05.1999
• Construction Year to: 08.2002
• Resistor [Ohm]: 900
• Colour: black
• Cable Length [mm]: 570
• Number of pins: 3
• Fitting Depth [mm]: 24
• Supplementary Article/Info 2: with seal ring
• Weight [kg]: 0.072
• Manufacturer: ERA

• Voltage [V]: 12
• Number of pins: 3
• Guarantee: 3 years guarantee
• Weight [kg]: 0.11
• Operating Mode: Electric
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 17SKV366

• Engine Code: AGR, ALH
• Vehicle Identification Number (VIN) from: ******6K*Y*021001
• Length [mm]: 535
• Number of connectors: 3
• Cable Length [mm]: 450
• Weight [kg]: 0.1
• Supplementary Article/Info 2: with seal ring
• Manufacturer: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Sensor Type: Inductive Sensor
• Number of pins: 3
• Voltage [V]: 12
• Connector Shape: D Shape
• Supplementary Article/Info 2: with cable
• Resistor [Ohm]: 900
• Weight [kg]: 0.09
• Manufacturer: VALEO
• Name: VA 254003
• Lisainfo: VAL254003
• Additional information: VAL254003

• Engine Code: AGR, ALH
• Vehicle Identification Number (VIN) from: 6K-Y-021 001
• Weight [kg]: 0.126
• for OE number: 038 957 147 C
• Number of pins: 3
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Number of pins: 3
• Guarantee: 3 years guarantee
• Weight [kg]: 0.04
• Always compare old and new part (in particular OE No.):
• Name: CE 17SKV554
• Manufacturer: ESEN SKV

• Engine Code: 1Z
• Cable Length [mm]: 500
• Alternatively:
• Number of pins: 3
• Fitting Depth [mm]: 46
• Supplementary Article/Info 2: with seal ring
• Weight [kg]: 0.076
• Alternative Repair Kit: 550102
• Manufacturer: ERA

• Connector Shape: rectangular
• Number of pins: 3
• Supplementary Article/Info 2: with cable
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Fitting Position: Oil Sump
• Number of pins: 3
• Connector Shape: D Shape
• Supplementary Article/Info 2: with seal ring
• Number of mounting bores: 3
• Housing Type: Aluminium Housing
• Housing material: Plastic, Polyamid 6.6
• Housing Colour: black
• for OE number: 1 119 169, 1J0 907 660B
• Observe system fill quantity:
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Cable Length [mm]: 500
• Number of pins: 3
• Fitting Depth [mm]: 46
• Resistor [kOhm]: 1.1
• Manufacturer: ERA

• Required quantity: 1
• Vehicle Identification Number (VIN) from: 6K-X-400 000
• Vehicle Identification Number (VIN) to: 6K-Y-021 000
• Number of pins: 3
• Manufacturer: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.