• Weight [kg]: 0.022
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Engine Code: B 6324 S
• for article number: 1.880.846
• Name: EP 1.830.346
• Manufacturer: EPS

• Sensor Type: NTC Sensor
• Number of pins: 2
• Housing Colour: black
• Manufacturer: FAE

• Fabrication Number: ECP-VV-000
• Manufacturer: NTY

• Number of pins: 3
• Name: DE SS12311-12B1
• Manufacturer: DELPHI

• Fabrication Number: ECM-VV-000
• Manufacturer: NTY

• Construction Year from: 08.2007
• Required quantity: 2
• Number of pins: 3
• Sensor Type: Hall Sensor
• Supplementary Article/Info 2: with seal ring
• Assy./disassy. by qualified personnel required!:
• Name: HE 6PU358380691
• Manufacturer: HELLA

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Sensor Type: Hall Sensor
• Number of pins: 3
• Manufacturer: ABAKUS LORO

General Information: The following information is for general and informational purposes only and does not constitute warranty terms. Warranty terms and conditions are available from our dealers and in our general terms and conditions of sale. Abakus spare/repair parts are intended only for vehicle repairs in order to restore their original functionality. Abakus spare/repair parts are used or sold to users only for the purpose of repairing vehicles to restore their original look and functionality and are not original/genuine/OE/OEM/OES replacement parts. These items do not originate from the vehicle manufacturer and may be the subject of a design not owned by Abakus. They may only be used for repairs to restore the intended vehicle to its original appearance. Our products are delivered without instruction of installation. Installation of our product may only be carried out by trained specialist technicians in specific car repairs. Products supplied by us are exclusively intended for proper and appropriate use. The warranty may become invalid in the event of: improper installation or repair, unsuitable application or use, installation or repair made outside specialist car workshops. Warranty claims are lost if the vehicle is modified and used for motor sports, tuning or similar events (except our tuning parts which are described in TecDoc and on our price list). Warranty application should include complete documentation among others: chassis no., first registration, vehicle mileage, information about LPG installation, fault memory log, pictures, our QC (quality check) code, installation invoice, contact details of the car repair workshop performing the replacement or repair. Warranty application are available in our Client Panel system. Complaints may require supplementing data such as error memory logs. Incomplete documentation may result in rejection of the claim. Any damage caused during transport is not considered quality damage and will be considered on an individual basis. The product is intended for use within the performance limits specified by the manufacturer and should only be used by qualified personnel who have been trained to operate this product. Before each use, the product should be checked for damage or fixing of its parts and not used if any defects or loose parts are found. Failure to follow the manufacturer's guidelines could result in potential product damage or even injury. Wear appropriate protective clothing if necessary when working with the product.

• Oxygen Sensor: Diagnostic Probe, Thread pre-greased
• Fabrication Number: ESL-SK-000
• Manufacturer: NTY
• Name: NTY ESL-SK-000

• Required quantity: 1
• Voltage [V]: 12
• Number of pins: 3
• Sensor Type: Hall Sensor
• Supplementary Article/Info 2: without cable
• Housing Colour: black
• Manufacturer: BREMI

• Oxygen Sensor: Diagnostic Probe
• Fabrication Number: ESL-VV-003
• Cable Length [mm]: 360
• Manufacturer: NTY

• Housing Type: without housing
• Fabrication Number: EPP-MZ-001
• Manufacturer: NTY
• Name: NTY EPP-MZ-001

• Sensor Type: Hall Sensor
• Number of pins: 3
• Connector Shape: oval
• Manufacturer: ERA

• Number of pins: 5
• Connector Shape: rectangular
• Manufacturer: ABAKUS

General Information: The following information is for general and informational purposes only and does not constitute warranty terms. Warranty terms and conditions are available from our dealers and in our general terms and conditions of sale. Abakus spare/repair parts are intended only for vehicle repairs in order to restore their original functionality. Abakus spare/repair parts are used or sold to users only for the purpose of repairing vehicles to restore their original look and functionality and are not original/genuine/OE/OEM/OES replacement parts. These items do not originate from the vehicle manufacturer and may be the subject of a design not owned by Abakus. They may only be used for repairs to restore the intended vehicle to its original appearance. Our products are delivered without instruction of installation. Installation of our product may only be carried out by trained specialist technicians in specific car repairs. Products supplied by us are exclusively intended for proper and appropriate use. The warranty may become invalid in the event of: improper installation or repair, unsuitable application or use, installation or repair made outside specialist car workshops. Warranty claims are lost if the vehicle is modified and used for motor sports, tuning or similar events (except our tuning parts which are described in TecDoc and on our price list). Warranty application should include complete documentation among others: chassis no., first registration, vehicle mileage, information about LPG installation, fault memory log, pictures, our QC (quality check) code, installation invoice, contact details of the car repair workshop performing the replacement or repair. Warranty application are available in our Client Panel system. Complaints may require supplementing data such as error memory logs. Incomplete documentation may result in rejection of the claim. Any damage caused during transport is not considered quality damage and will be considered on an individual basis. The product is intended for use within the performance limits specified by the manufacturer and should only be used by qualified personnel who have been trained to operate this product. Before each use, the product should be checked for damage or fixing of its parts and not used if any defects or loose parts are found. Failure to follow the manufacturer's guidelines could result in potential product damage or even injury. Wear appropriate protective clothing if necessary when working with the product.

• Number of pins: 5
• Manufacturer: ABAKUS

General Information: The following information is for general and informational purposes only and does not constitute warranty terms. Warranty terms and conditions are available from our dealers and in our general terms and conditions of sale. Abakus spare/repair parts are intended only for vehicle repairs in order to restore their original functionality. Abakus spare/repair parts are used or sold to users only for the purpose of repairing vehicles to restore their original look and functionality and are not original/genuine/OE/OEM/OES replacement parts. These items do not originate from the vehicle manufacturer and may be the subject of a design not owned by Abakus. They may only be used for repairs to restore the intended vehicle to its original appearance. Our products are delivered without instruction of installation. Installation of our product may only be carried out by trained specialist technicians in specific car repairs. Products supplied by us are exclusively intended for proper and appropriate use. The warranty may become invalid in the event of: improper installation or repair, unsuitable application or use, installation or repair made outside specialist car workshops. Warranty claims are lost if the vehicle is modified and used for motor sports, tuning or similar events (except our tuning parts which are described in TecDoc and on our price list). Warranty application should include complete documentation among others: chassis no., first registration, vehicle mileage, information about LPG installation, fault memory log, pictures, our QC (quality check) code, installation invoice, contact details of the car repair workshop performing the replacement or repair. Warranty application are available in our Client Panel system. Complaints may require supplementing data such as error memory logs. Incomplete documentation may result in rejection of the claim. Any damage caused during transport is not considered quality damage and will be considered on an individual basis. The product is intended for use within the performance limits specified by the manufacturer and should only be used by qualified personnel who have been trained to operate this product. Before each use, the product should be checked for damage or fixing of its parts and not used if any defects or loose parts are found. Failure to follow the manufacturer's guidelines could result in potential product damage or even injury. Wear appropriate protective clothing if necessary when working with the product.

• Number of pins: 5
• Housing Type: without housing
• Lisainfo: Air Mass Sensor
• Additional information: Air Mass Sensor

• Number of pins: 5
• Recommended additional repairs: Air Filter
• Used part return not required:
• Fitting Position: Air Filter Housing
• New Part:
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Construction Year to: 07.2010
• Supplementary Article/Info 2: Low Pressure Side
• Fuel Mixture Formation: Manifold Injection/Direct Injection
• Manufacturer: BOSCH
• Name: BS 0261230238

• Voltage [V]: 12
• Number of pins: 5
• Guarantee: 3 years guarantee
• New Part:
• Used part return not required:
• Weight [kg]: 0.11
• Operating Mode: Electric
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 07SKV107

• Pistikkontaktide arv: 5
• Manufacturer: JPN

• Number of pins: 5
• New Part:
• Used part return not required:
• Recommended additional repairs: Air Filter
• Weight [kg]: 0.045
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Voltage [V]: 12
• Number of pins: 5
• Guarantee: 3 years guarantee
• New Part:
• Used part return not required:
• Weight [kg]: 0.11
• Operating Mode: Electric
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 07SKV151

• Construction Year to: 07.2010
• Fuel Mixture Formation: Direct Injection
• Supplementary Article/Info 2: Low Pressure Side
• Version: IAM
• Manufacturer: METZGER

Manufacturer: MAGNETI MARELLI

• Required quantity: 1
• Voltage [V]: 12
• Number of pins: 5
• Housing Type: without housing
• Manufacturer: BREMI

• Fitting Position: after catalytic converter
• Cable Length [mm]: 484
• Oxygen Sensor: Planar probe, Heated
• Name: DE ES20364-12B1
• Manufacturer: DELPHI
• Lisainfo: ES20364-12B1
• Additional information: ES20364-12B1

• Engine Code: B 6324 S
• Required quantity: 1
• Housing Type: without housing
• Name: EP 1.991.163
• Manufacturer: EPS

• Engine Code: B 6324 S
• Required quantity: 1
• Housing Type: without housing
• Manufacturer: FACET

• Construction Year to: 07.2010
• Number of pins: 4
• Connector Shape: oval
• Colour: grey
• Number of mounting bores: 1
• Fuel Mixture Formation: Intake Manifold Injection
• Supplementary Article/Info 2: Low Pressure Side
• for OE number: 1582665
• Manufacturer: MEAT&DORIA

• Number of pins: 5
• Supplementary Article/Info 2: with seal ring
• Number of Holes: 2
• Manufacturer: ERA

• Fitting Position: Left, Right
• for OE number: 30756122
• Quality: OE
• Manufacturer Restriction: DENSO
• Thread Size: M18x1.5
• Cable Length [mm]: 430
• Number of pins: 4
• Weight [g]: 91
• Gross Weight [g]: 124
• Name: DN DOX-0408
• Manufacturer: DENSO

Oxygen Sensor: Diagnostic Probe, Heated, Finger probe, Thread pre-greased, Oxygen Sensor

• Alternatively:
• Required quantity: 1
• Voltage [V]: 12
• Number of pins: 5
• Housing Type: without housing
• Manufacturer: BREMI

• Construction Year to: 07.2010
• Oxygen Sensor: Diagnostic Probe, Thread pre-greased
• Fitting Position: after catalytic converter
• Required quantity: 2
• Line insulation design: with silicone-coated woven-fibre insulation
• Thread Size: M18x1,5
• Cable Length [mm]: 360
• Conductor Number: 4
• Connector Shape: angular
• Length [mm]: 360
• Number of pins: 4
• Weight [kg]: 0.1
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Engine Code: B 6324 S
• Fitting Position: Left, Right, Front, after catalytic converter
• Required quantity: 2
• Cable Length [mm]: 450
• Conductor Number: 4
• Available as universal article as well, see article no.: 1.998.235
• Number of circuits: 4
• Name: EP 1.998.601
• Manufacturer: EPS
• Additional information: EP 1.998.601
• Lisainfo: EP 1.998.601

Oxygen Sensor: Diagnostic Probe, Heated, Planar probe, Thread pre-greased

• Construction Year from: 08.2007
• Required quantity: 1
• Mounting Type: Bolted
• Number of pins: 5
• Housing Colour: black
• Plug Type: Male
• Assy./disassy. by qualified personnel required!:
• Manufacturer: HELLA
• Name: HE 8ET009142891

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Oxygen Sensor: Regulating Probe
• Exhaust System: for pre-catalytic converter
• for OE number: 30756121
• Length [mm]: 700
• Number of pins: 4
• Manufacturer: FAE ELEKTRYKA

• Housing Type: without housing
• Number of pins: 5
• Plug Type: Male
• Housing Colour: black
• Voltage [V]: 12
• Recommended additional repairs: Air Filter
• Manufacturer: DELPHI
• Name: DE AF10135-12B1

• for OE number: 30756121
• Fitting Position: Left
• Oxygen Sensor: Regulating Probe, Heated
• External Thread Size: M18 x 1,5
• Spanner Size: 22
• Number of circuits: 4
• Cable Length [mm]: 460
• Weight [kg]: 0.092
• Name: SW 33 10 3141
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• for OE number: 22204-21010
• Quality: OE
• Operating Mode: Electric
• Number of pins: 5
• Gross Weight [g]: 79
• alternative item: -
• Manufacturer: DENSO

Additional information: "Tootja: DENSO
HILUX SAMOCHÓD TEREN
(kvaliteediklass: Q)" Lisainfo: "Tootja: DENSO
HILUX SAMOCHÓD TEREN
(kvaliteediklass: Q)"

• Operating Mode: Electric
• Manufacturer: MAGNETI MARELLI

• Fitting Position: Left, Right
• for OE number: 30756121, 30713864
• Exhaust System: for pre-catalytic converter
• Quality: OE
• Manufacturer Restriction: DENSO
• Thread Size: M18x1.5
• Cable Length [mm]: 650
• Number of pins: 4
• Weight [g]: 110
• Gross Weight [g]: 138
• Manufacturer: DENSO
• Name: DN DOX-0526

Oxygen Sensor: Regulating Probe, Heated, Finger probe, Broadband oxygen sensor

• Number of mounting bores: 3
• Number of pins: 6
• Transmission Type: Automatic Transmission
• Left-/right-hand drive vehicles: for left-hand drive vehicles
• Assy./disassy. by qualified personnel required!:
• Name: HE 6PV010834811
• Manufacturer: HELLA

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Engine Code: B 6324 S
• Operating Mode: Electric
• Voltage [V]: 12
• Manufacturer: PIERBURG

• Number of mounting bores: 3
• Number of pins: 6
• Transmission Type: Manual Transmission
• Left-/right-hand drive vehicles: for left-hand drive vehicles
• Assy./disassy. by qualified personnel required!:
• Manufacturer: HELLA

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Number of pins: 6
• Connector Shape: oval
• Number of mounting bores: 3
• Vehicle Equipment: for vehicles with automatic transmission
• Left-/right-hand drive vehicles: for left-hand drive vehicles
• for OE number: 31329058
• Manufacturer: MEAT&DORIA

• Construction Year to: 07.2010
• Fitting Position: Exhaust Manifold
• Required quantity: 2
• Oxygen Sensor: Diagnostic Probe
• Number of pins: 4
• Cable Length [mm]: 520
• Quality: OE EQUIVALENT
• for OE number: MHK501140
• Manufacturer: MEAT&DORIA