• Supplementary Article/Info 2: without cable
• Fitting Position: Right, Exhaust Side, Intake Side
• Fabrication Number: ECP-BM-000
• Manufacturer: NTY

• Engine Code: N45 B16 A
• Thread Size: M12x1,5
• Spanner Size: 22
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: EPS

• Sensor Type: Active sensor
• for OE number: 12 14 1 435 351
• Manufacturer: KAMOKA

• Fitting Position: Exhaust Side
• Connector Shape: oval
• Number of pins: 3
• Supplementary Article/Info 2: with seal ring, without cable
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• for OE number: 13 62 7 525 014
• Sensor Type: Hall Sensor
• Number of pins: 3
• Fitting Depth [mm]: 28
• Supplementary Article/Info 2: without cable
• Connector Shape: oval
• Number of mounting bores: 1
• Fabrication Number: ECP-BM-005
• Manufacturer: NTY

• Engine Code: N45 B16 A
• Required quantity: 2
• Weight [g]: 0.03
• Number of pins: 3
• Connector Shape: oval
• Name: ANDUR,NUKKVOLLIPOSITSIOON
• Manufacturer: MAX

• Number of pins: 2
• Housing Colour: black
• Manufacturer: FAE

• Transmission Type: Manual Transmission
• Number of pins: 2
• Weight [kg]: 0.026
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Sensor Type: Active sensor
• for OE number: 13 62 7 787 192
• Manufacturer: KAMOKA

• Required quantity: 2
• Voltage [V]: 12
• Number of pins: 3
• Sensor Type: Hall Sensor
• Supplementary Article/Info 2: without cable
• Housing Colour: black
• Manufacturer: BREMI

• Supplementary Article/Info 2: without cable
• Number of pins: 3
• Name: ANDUR,NUKKVOLLIPOSITSIOON
• Manufacturer: DLP
• Quality class: PJ

Additional information: "Tootja: DELPHI
(kvaliteediklass: PJ)" Lisainfo: "Tootja: DELPHI
(kvaliteediklass: PJ)"

• Height [mm]: 28.2
• Sensor Type: Hall Sensor
• Number of connectors: 3
• Manufacturer: VERNET

• Colour: black
• Number of pins: 3
• Fabrication Number: ECM-BM-005
• Manufacturer: NTY

Lisainfo: ENG. 1.6,1.8,2.0,2.5,3.0,4.4 BMW 1 (E81/87) 04-12, 3 (E46/90) 01-13, 5 (E60/61) 05-10, X3 (E83)05-10, X5 (E53/70) 01-10 Additional information: ENG. 1.6,1.8,2.0,2.5,3.0,4.4 BMW 1 (E81/87) 04-12, 3 (E46/90) 01-13, 5 (E60/61) 05-10, X3 (E83)05-10, X5 (E53/70) 01-10

• Voltage [V]: 12
• Supplementary Article/Supplementary Info: without cable pull
• Number of pins: 3
• Weight [kg]: 0.04
• Operating Mode: Electric
• Warranty: 3 years warranty
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY

• Engine Code: N43 B16A, N45 B16A
• Number of sensors: 2
• Sensor Type: Hall Sensor
• Number of pins: 3
• Voltage [V]: 12
• Connector Shape: D Shape
• Supplementary Article/Info 2: without cable
• Weight [kg]: 0.04
• Name: ANDUR,NUKKVOLLIPOSITSIOON
• Manufacturer: VAL

• Fitting Position: Intake Manifold
• Number of pins: 3
• Supplementary Article/Info 2: with seal ring
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Required quantity: 1
• Name: CZUJNIK CI—N. POWIETRZA BMW 5 F10
• Manufacturer: BRM

• Number of circuits: 4
• Lambda Sensor: Regulating Probe
• Manufacturer: KAMOKA

• Required quantity: 2
• Voltage [V]: 12
• Sensor Type: Hall Sensor
• Supplementary Article/Supplementary Info: with seal
• Number of pins: 3
• Supplementary Article/Info 2: without cable
• Number of mounting bores: 1
• Assy./disassy. by qualified personnel required!:
• Manufacturer: HELLA
• Name: HE 6PU009121701

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Lambda Sensor: Diagnostic Probe, Thread pre-greased
• Overall Length [mm]: 480
• Number of circuits: 4
• Fitting Position: after catalytic converter
• Fabrication Number: ESL-BM-001
• Manufacturer: NTY

Lisainfo: ENG. 1.6,2.0,3.0 BMW 1 (E81,E82, E87,E88) 07-13, 3 (E90,E91,E92,E93) 05-13, 5 (E60,E61) 05-10, 7 (E65,E66,E67) 05-08, X1 (E84) 09-18, /DIAGNOSTYCZNA, ZA KATALIZATOREM, Dœ.CAœK. 480MM Additional information: ENG. 1.6,2.0,3.0 BMW 1 (E81,E82, E87,E88) 07-13, 3 (E90,E91,E92,E93) 05-13, 5 (E60,E61) 05-10, 7 (E65,E66,E67) 05-08, X1 (E84) 09-18, /DIAGNOSTYCZNA, ZA KATALIZATOREM, Dœ.CAœK. 480MM

• Number of pins: 3
• Sensor Type: Hall Sensor
• Supplementary Article/Info 2: without cable
• Manufacturer: FAE

• Lambda Sensor: Diagnostic Probe, Thread pre-greased
• Fabrication Number: ESL-SK-000
• Manufacturer: NTY
• Name: NTY ESL-SK-000

• Number of pins: 5
• Plug Type: Male
• Fabrication Number: EPP-BM-021
• Manufacturer: NTY

• Length [mm]: 210
• Number of pins: 3
• Fitting Depth [mm]: 14
• Resistor M[ohm]: 13.5
• Manufacturer: ERA

• Technical Information Number: Universal
• Overall Length [mm]: 325
• Number of pins: 4
• Lambda Sensor: Regulating Probe
• Manufacturer: ASHIKA
• Lisainfo: 43-U04
• Additional information: 43-U04

• Fabrication Number: ESS-BM-003
• Manufacturer: NTY

• Number of pins: 3
• Supplementary Article/Info 2: without cable
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Sensor Type: Hall Sensor
• Alternatively:
• Number of pins: 3
• Fitting Depth [mm]: 28
• Alternative Repair Kit: 550604
• Manufacturer: ERA

• Technical Information Number: Universal
• Overall Length [mm]: 325
• Number of pins: 4
• Lambda Sensor: Regulating Probe
• Manufacturer: JAPKO

• for OE number: 13 62 1 438 687
• Manufacturer: KAMOKA

• Number of pins: 3
• Name: ANDUR,NUKKVOLLIPOSITSIOON
• Manufacturer: DLP

• Construction Year to: 03.2009
• Engine Code: N43B16A
• Sensor Type: Hall Sensor
• Number of pins: 3
• Connector Shape: oval
• Supplementary Article/Info 2: without cable
• Weight [kg]: 0.02
• Manufacturer: VALEO
• Name: VA 366149

• Lambda Sensor: Lambda Sensor
• Voltage [V]: 12
• Number of circuits: 4
• Weight [kg]: 0.09
• Resistor [Ohm]: 9
• Operating Mode: Electric
• Warranty: 3 years warranty
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY

• Housing Type: with housing
• Number of pins: 5
• Plug Type: Male
• Voltage [V]: 12
• Quality class: PJ
• Name: Air flow sensor

• Lambda Sensor: Lambda Sensor
• Weight [kg]: 0.12
• Warranty: 3 years warranty
• Always compare old and new part (in particular OE No.):
• Name: CE 09SKV121
• Manufacturer: ESEN SKV

• Number of pins: 3
• Colour: black
• Manufacturer: FAE

• Engine Code: N45 B16 A
• Lambda Sensor: Diagnostic Probe
• Number of circuits: 4
• Supplementary Article/Info 2: without plug
• Manufacturer: ENERGY

• Engine Code: N45B16A
• Number of pins: 5
• Housing Type: with housing
• Manufacturer: JP GROUP
• Lisainfo: Air Mass Sensor
• Additional information: Air Mass Sensor

• for OE number: 13 62 7 525 014
• Name: ANDUR,NUKKVOLLIPOSITSIOON
• Manufacturer: TRU

• Lambda Sensor: Diagnostic Probe
• Fitting Position: after catalytic converter
• Number of pins: 4
• Overall Length [mm]: 480
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Lambda Sensor: Lambda Sensor
• Cable Length [mm]: 650
• Conductor Number: 4
• Warranty: 3 years warranty
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 09SKV140

• Sensor Type: Hall Sensor
• Number of pins: 3
• Weight [kg]: 0.025
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Number of pins: 3
• for OE number: 13 62 8 617 097
• Manufacturer: MEAT&DORIA

• Lambda Sensor: Diagnostic Probe, Heated
• Fitting Position: after catalytic converter
• Number of circuits: 4
• Overall Length [mm]: 480
• Name: Lambda andur
• Manufacturer: MAX

• Engine Code: N45 B16 A
• Required quantity: 2
• Weight [g]: 0.03
• Name: EP 1.953.471
• Manufacturer: EPS

• Length [mm]: 49
• Number of connectors: 3
• Weight [kg]: 0.03
• Supplementary Article/Info 2: with seal ring
• Manufacturer: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Housing Type: with housing
• Number of pins: 5
• Housing material: Plastic
• Connector Shape: D Shape
• Recommended additional repairs: Air Filter
• Manufacturer: TOPRAN HANS PRIES

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Lambda Sensor: Diagnostic Probe, Heated
• External Thread Size: M18 x 1,5
• Spanner Size: 22
• Number of circuits: 4
• Cable Length [mm]: 650
• Weight [kg]: 0.095
• Name: SW 33 10 3198
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Voltage [V]: 12
• Number of pins: 5
• Weight [kg]: 0.07
• Operating Mode: Electric
• Warranty: 3 years warranty
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 07SKV502

Manufacturer: MAGNETI MARELLI

• Engine Code: N45 B16 A
• Line insulation design: with silicone-coated woven-fibre insulation
• Number of pins: 4
• for OE number: V99760001
• Cable Length [mm]: 210
• Number of circuits: 4
• Weight [kg]: 0.09
• Length [mm]: 350
• Exhaust System: after catalytic converter
• Manufacturer: VEMO GERMANY

Lambda Sensor: Diagnostic Probe, Finger probe, Heated, Thread pre-greased Supplementary Article/Supplementary Info: with squeeze connector, with shrink squeeze connector General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Engine Code: N45
• Fitting Position: after catalytic converter
• Line insulation design: with silicone-coated woven-fibre insulation
• Lambda Sensor: Planar probe, Heated, Thread pre-greased
• Cable Length [mm]: 210
• Number of circuits: 4
• Weight [kg]: 0.09
• Manufacturer: VEMO GERMANY

Supplementary Article/Supplementary Info: with squeeze connector, with shrink squeeze connector General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Connector Shape: D Shape
• Number of pins: 2
• Voltage [V]: 12
• Fitting Depth [mm]: 35
• Cable Length [mm]: 1,195
• Thread Size: M14x1.5
• Supplementary Article/Supplementary Info: with synthetic grease
• Name: Andur, heitgaasitemperatuur
• Manufacturer: NRF

• Exhaust System: for pre-catalytic converter
• Cable Length [mm]: 614
• Lambda Sensor: Planar probe, Heated
• Manufacturer: DELPHI
• Name: DE ES20368-12B1

• Number of pins: 3
• Manufacturer: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Quality: OE
• Manufacturer Restriction: DENSO
• Thread Size: M18x1.5
• Cable Length [mm]: 750
• Number of pins: 4
• Weight [g]: 93
• Gross Weight [g]: 140
• Manufacturer: DENSO
• Name: DN DOX-0150
• Quality class: Q

Lambda Sensor: Diagnostic Probe, Heated, Planar probe, Thread pre-greased, Lambda Sensor Additional information: "Tootja: DENSO
(kvaliteediklass: Q)" Lisainfo: "Tootja: DENSO
(kvaliteediklass: Q)"

• Cable Length [mm]: 200
• Number of pins: 4
• Manufacturer: DELPHI
• Name: DE AS10241

• Number of pins: 3
• Sensor Type: Hall Sensor
• Warranty: 5 years warranty
• General Information: Sold in Hueco brand: printing and packaging
• Manufacturer: HUCO

• Engine Code: N45 B16 A
• Required quantity: 1
• Housing Colour: black
• Length [mm]: 225
• Cable Length [mm]: 315
• Name: DETONATSIOONIANDUR
• Manufacturer: EPS

• Lambda Sensor: Heated
• Number of pins: 4
• Cable Length [mm]: 450
• for article number: 81633E
• Quality: OE EQUIVALENT
• Name: Lambda andur
• Manufacturer: MD

• Number of pins: 3
• Manufacturer: METZGER

• Operating Mode: Electric
• Manufacturer: MAGNETI MARELLI

• Required quantity: 1
• Voltage [V]: 12
• Number of pins: 5
• Name: OHUMASSIMOOTJA
• Manufacturer: BRM

• Lambda Sensor: Lambda Sensor
• Cable Length [mm]: 640
• Number of pins: 6
• Total Length [mm]: 780
• Manufacturer: ERA

• Lambda Sensor: Diagnostic Probe
• Fitting Position: after catalytic converter
• Number of circuits: 4
• Overall Length [mm]: 480
• Recommended change interval [km]: 250,000
• Name: LAMBDA ANDUR
• Manufacturer: BOS

• Lambda Sensor: Regulating Probe
• Number of connectors: 4
• Length [mm]: 620
• Manufacturer: METZGER

• Line insulation design: with silicone-coated woven-fibre insulation
• Thread Size: M18 x 1,5
• Cable Length [mm]: 360
• Conductor Number: 4
• Connector Shape: round
• Length [mm]: 450
• Number of circuits: 4
• Exhaust System: after catalytic converter
• Weight [kg]: 0.095
• Lambda Sensor: Thread pre-greased
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Lambda Sensor: Lambda Sensor
• Voltage [V]: 12
• Colour: red
• Number of circuits: 5
• Weight [kg]: 0.15
• Operating Mode: Electric
• Warranty: 3 years warranty
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 09SKV905

• Housing Type: with housing
• Number of pins: 5
• Plug Type: Male
• Housing Colour: black
• Voltage [V]: 12
• Recommended additional repairs: Air Filter
• Name: OHUMASSIMOOTJA
• Manufacturer: DLP

• Engine Code: N45 B16 A
• Fitting Position: before catalytic converter
• Required quantity: 1
• Colour: black
• Length [mm]: 680
• Cable Length [mm]: 720
• Conductor Number: 5
• Number of circuits: 5
• Name: EP 1.998.477
• Manufacturer: EPS

Lambda Sensor: Regulating Probe, Heated, Planar probe, Broadband lambda sensor, Thread pre-greased

• Housing Type: without housing
• Number of pins: 5
• Plug Type: Male
• Housing Colour: black
• Voltage [V]: 12
• Recommended additional repairs: Air Filter
• Manufacturer: DELPHI
• Name: DE AF10233-12B1

• Number of pins: 9
• Weight [kg]: 0.08
• Warranty: 3 years warranty
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 17SKV424

• Lambda Sensor: Broadband lambda sensor
• Thread Size: M18 x 1,5
• Cable Length [mm]: 720
• Number of pins: 6
• Fitting Position: before catalytic converter
• Name: Lambda andur
• Manufacturer: MEY

• Number of pins: 9
• Weight [kg]: 0.1
• Warranty: 3 years warranty
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 17SKV423

• Lambda Sensor: Regulating Probe
• Fitting Position: before catalytic converter
• Number of circuits: 5
• Overall Length [mm]: 720
• Recommended change interval [km]: 250,000
• Manufacturer: BOSCH
• Name: BS 0258017130

• Engine Code: N45 B16 A
• Fitting Position: before catalytic converter
• Line insulation design: with silicone-coated woven-fibre insulation
• Thread Size: M18 x 1,5
• Conductor Number: 5
• Connector Shape: D Shape
• Length [mm]: 700
• Alternatively:
• Number of pins: 5
• Lambda Sensor: Regulating Probe, Thread pre-greased
• Exhaust System: before catalytic converter
• Weight [kg]: 0.156
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Engine Code: N45 B16 A
• Fitting Position: before catalytic converter
• Lambda Sensor: Regulating Probe, Heated
• Voltage [V]: 12
• Conductor Number: 5
• Cable Length [mm]: 700
• Number of pins: 6
• Name: LAMBDA ANDUR
• Manufacturer: PIE