• Operating voltage [V]: 12
• Sensor Type: NTC Sensor
• Switch Point [°C]: -40, 150
• Thread Size: M12x1,5
• Spanner Size: 22
• Colour: black
• Number of pins: 2
• Manufacturer: JP GROUP
• Lisainfo: Temperature sensor for cooling system
• Additional information: Temperature sensor for cooling system

• Fitting Position: Cylinder Head
• Length [mm]: 48
• Housing Colour: black
• Spanner Size: 22
• Manufacturer: KAMOKA

• Fabrication Number: ECT-BM-011
• Manufacturer: NTY

• Relay Number: K6342
• Supplementary Article/Info 2: with resistor
• Supplementary Article/Supplementary Info: without holder
• Protection Type (IP Code): IP54
• Voltage [V]: 12
• Capacity at 12V: 10/20A
• Inductive Load [A]: 10, 20
• Capacitive Load [A]: 10, 20
• Ohmic Load [A]: 10, 20
• Number of pins: 5
• Wiring Diagramme: W2
• Combi Switch Function: Changeover Contact
• Plug Type ID: C1
• Temperature range [°C]: 80
• Assy./disassy. by qualified personnel required!:
• Name: Relee,Udutuled
• Manufacturer: HEL

Relay function: Engine control unit, Comfort Equipment Variant (trim package) Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Thread Size: M 12x1,5
• Housing Colour: brown
• Number of pins: 1
• Manufacturer: FAE

• Sensor Type: NTC Sensor
• Mounting Type: Bolted
• Connector Shape: rectangular
• Number of pins: 2
• Socket colour: black
• Spanner Size: 22
• Thread Size: M12x1.5
• for OE number: 13621433076
• Supplementary Article/Info 2: with seal ring
• Name: Andur,Jahutusvedeliku temp.
• Manufacturer: NRF

• Connector Shape: rectangular
• Sensor Type: NTC Sensor
• Thread Size: M 12
• Thread Pitch [mm]: 1.5
• Number of pins: 2
• Supplementary Article/Info 2: with seal ring
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Thread Size: M12x1.5
• Manufacturer: VERNET

• Spanner Size: 22
• Colour: black
• Fitting Position: Cylinder Head
• Number of pins: 2
• Thread Size: M12x1,5
• Length [mm]: 49
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: MAX

• Connector Shape: rectangular
• Material: Plastic
• Number of pins: 2
• Plug Type: Female
• Sensor Type: NTC Sensor
• Spanner Size: S22
• Thread Size: M12*1,5
• Name: NI 207088
• Manufacturer: NISSENS

Technical Information: FIRST FIT - a time-saving installation! Find all additional parts such as O-rings, clip, washer in the box.

• for OE number: 13 62 1 433 076
• Manufacturer: TRUCKTEC

• Engine Code: N53 B30 A, N52B30A
• Housing Colour: black
• Number of pins: 2
• Thread Size: M12X1.5-6g
• Spanner Size: 22
• Manufacturer: DELPHI
• Name: DE TS10270

• Length [mm]: 48.5
• External Thread Size: M12 x 1,5
• Spanner Size: 22
• Number of connectors: 2
• Colour: black
• Fitting Position: Cylinder Head
• Weight [kg]: 0.03
• Supplementary Article/Info 2: with seal ring
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: FEB

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Thread Size: M12 x 1,5
• Spanner Size: 22
• Number of pins: 2
• Manufacturer: ERA

• Engine Code: N53 B30 A, N53B30A
• Thread Size: M12x1,5
• Spanner Size: 22
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: EPS

• Length [mm]: 48.5
• External Thread Size: M12 x 1,5
• Spanner Size: 22
• Number of connectors: 2
• Colour: black
• Fitting Position: Cylinder Head
• Weight [kg]: 0.03
• Supplementary Article/Info 2: with seal ring
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• for OE number: 13 62 7 525 014
• Sensor Type: Hall Sensor
• Number of pins: 3
• Fitting Depth [mm]: 28
• Supplementary Article/Info 2: without cable
• Connector Shape: oval
• Number of mounting bores: 1
• Fabrication Number: ECP-BM-005
• Manufacturer: NTY

• Engine Code: N53B30A
• Thread Size: M12x1,5
• Spanner Size: 22
• Sensor Type: NTC Sensor
• Number of pins: 2
• Mounting Type: Vertical Screw Fitting
• Assy./disassy. by qualified personnel required!:
• Name: HE 6PT009107851
• Manufacturer: HELLA

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Engine Code: N53 B30 A
• Sensor Type: NTC Sensor
• Thread Size: M12 x 1,5
• Spanner Size: 22
• Colour: black
• Number of pins: 2
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: MEY

• Number of pins: 3
• Weight [kg]: 0.03
• Warranty: 3 years warranty
• Manufacturer: SKV GERMANY
• Name: CE 17SKV494

• Number of pins: 2
• Supplementary Article/Supplementary Info: with seal
• Weight [kg]: 0.3
• Packaging length [cm]: 12
• Packaging width [cm]: 8
• Packaging height [cm]: 6

• Fabrication Number: ECP-BM-001
• Number of pins: 3
• Supplementary Article/Info 2: without cable
• Colour: black
• Connector Shape: oval
• Sensor Type: Hall Sensor
• Manufacturer: NTY

• Supplementary Article/Info 2: without pipe
• Number of pins: 3
• Name: Andur, v„ntvoll
• Manufacturer: MAX

• Fabrication Number: ECC-CT-000
• Manufacturer: NTY

• Engine Code: N53 B30 A
• Sensor Type: Hall Sensor
• Alternatively:
• Number of pins: 3
• Alternative Repair Kit: 550470
• Rated Voltage [V]: 12
• Manufacturer: ERA

• Engine Code: N53 B30 A
• Alternatively:
• Number of pins: 3
• Required quantity: 1
• Sensor Type: Hall Sensor
• Supplementary Article/Info 2: for crankshaft
• Number of connectors: 3
• Rated Voltage [V]: 12
• Weight [kg]: 0.021
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Number of pins: 3
• Name: Andur, v„ntvoll
• Manufacturer: DLP

• Engine Code: N53 B30 A
• Required quantity: 2
• Sensor Type: Active sensor
• Number of pins: 3
• Voltage [V]: 12
• Name: Andur,Nukkvollipositsioon
• Manufacturer: MAX

• Number of pins: 3
• Connector Shape: oval
• Supplementary Article/Info 2: without cable
• Name: ANDUR, VŽNTVOLL
• Manufacturer: HAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Observe mounting information:
• only in connection with: M6X16-AL
• Sensor Type: Hall Sensor
• Number of pins: 3
• Name: Andur, v„ntvoll
• Manufacturer: MEY

• Number of connectors: 3
• Weight [kg]: 0.025
• Name: SW 33 10 2687
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Required quantity: 1
• Voltage [V]: 12
• Number of pins: 3
• Sensor Type: Hall Sensor
• Supplementary Article/Info 2: without cable
• Housing Colour: black
• Name: CZUJNIK POO½ENIA WAU KORB. BMW 3 E90 2,5 06-
• Manufacturer: BRM

• Number of circuits: 4
• Lambda Sensor: Regulating Probe
• Manufacturer: KAMOKA

• Number of connectors: 3
• Weight [kg]: 0.025
• Manufacturer: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Fabrication Number: ESS-BM-001
• Number of pins: 4
• Manufacturer: NTY

• Resistor Type: Hall Sensor
• Height [mm]: 27.8
• Manufacturer: VERNET

• Engine Code: N53B30A
• Voltage [V]: 12
• Sensor Type: Hall Sensor
• Number of pins: 3
• Assy./disassy. by qualified personnel required!:
• Name: HE 6PU009163301
• Manufacturer: HELLA

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Number of pins: 3
• Supplementary Article/Info 2: without cable
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Sensor Type: Hall Sensor
• Alternatively:
• Number of pins: 3
• Fitting Depth [mm]: 28
• Alternative Repair Kit: 550604
• Manufacturer: ERA

Number of pins: 3

• Engine Code: N53 B30 A, N53B30A
• Required quantity: 2
• Name: ANDUR,NUKKVOLLIPOSITSIOON
• Manufacturer: EPS

• Required quantity: 2
• Voltage [V]: 12
• Number of pins: 3
• Sensor Type: Hall Sensor
• Supplementary Article/Info 2: without cable
• Housing Colour: black
• Name: CZUJNIK POO½ENIA WAKA ROZRZ. BMW 1 E81
• Manufacturer: BRM

• Sensor Type: Hall Sensor
• Number of pins: 3
• Connector Shape: oval
• Supplementary Article/Info 2: without cable
• Weight [kg]: 0.02
• Manufacturer: VALEO
• Name: VA 366149

• Engine Code: N53 B30 A, N53B30A
• Thread Size: M12x1,5
• Spanner Size: 24
• Name: EP 1.980.001
• Manufacturer: EPS

• Engine Code: N53 B30 A
• Thread Size: M12 x 1,5
• Name: Rongastihend,klapis„„r
• Manufacturer: MAX

• Number of pins: 4
• Plug Type: Male
• Fabrication Number: EPP-BM-023
• Manufacturer: NTY

• Number of pins: 3
• Name: ANDUR,NUKKVOLLIPOSITSIOON
• Manufacturer: DLP

• Engine Code: N53 B30 A
• Thread Size: M12 x 1,5
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Lambda Sensor: Diagnostic Probe, Finger probe
• Block Separation:
• Number of circuits: 4
• Connector/Clamp: Connector may need adjustment
• Transmission Type: Manual Transmission
• Name: LAMBDA ANDUR
• Manufacturer: MAX

Fitting Position: for cylinder 1-3, after catalytic converter, for cylinder 4-6

• for OE number: 13 62 7 525 014
• Name: ANDUR,NUKKVOLLIPOSITSIOON
• Manufacturer: TRU

• Length [mm]: 49
• Number of connectors: 3
• Weight [kg]: 0.03
• Supplementary Article/Info 2: with seal ring
• Manufacturer: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Required quantity: 2
• Number of pins: 3
• Fitting Depth [mm]: 27.8
• Name: ANDUR,NUKKVOLLIPOSITSIOON
• Manufacturer: TRI

• Number of pins: 3
• Connector Shape: oval
• Socket colour: black
• Thread Size: M12x1,5 mm
• for OE number: 1131.K8, 12 61 7 592 532
• Manufacturer: MEAT&DORIA

• Sensor Type: Hall Sensor
• Number of pins: 3
• Weight [kg]: 0.025
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Required quantity: 2
• Engine Code: N53B30A
• Voltage [V]: 12
• Corresponds to the original part in colour: black
• Sensor Type: Hall Sensor
• Number of pins: 3
• Number of mounting bores: 1
• Assy./disassy. by qualified personnel required!:
• Manufacturer: HELLA
• Name: HE 6PU009121011

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Number of pins: 3
• Housing Colour: black
• Sensor Type: Hall Sensor
• Manufacturer: FAE

Manufacturer: MAGNETI MARELLI

• Engine Code: N53 B30 A
• Colour: black
• Number of pins: 3
• Name: Andur,Nukkvollipositsioon
• Manufacturer: VDO

• Fabrication Number: EZC-BM-336
• Manufacturer: NTY

• Fitting Position: after catalytic converter
• Line insulation design: with silicone-coated woven-fibre insulation
• Lambda Sensor: Planar probe, Heated, Thread pre-greased
• Cable Length [mm]: 210
• Number of circuits: 4
• Weight [kg]: 0.09
• Manufacturer: VEMO GERMANY

Supplementary Article/Supplementary Info: with squeeze connector, with shrink squeeze connector General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Lambda Sensor: Diagnostic Probe
• Block Separation:
• Number of circuits: 4
• Recommended change interval [km]: 160,000
• Connector/Clamp: Connector may need adjustment
• Name: LAMBDA ANDUR
• Manufacturer: BOS

Fitting Position: after catalytic converter, for cylinder 1-3, for cylinder 4-6

• Engine Code: N53 B30 A, N53B30A
• Fitting Position: Left Front, after catalytic converter
• Required quantity: 1
• Length [mm]: 575
• Cable Length [mm]: 250
• Conductor Number: 4
• Number of circuits: 4
• Name: EP 1.998.235
• Manufacturer: EPS

Lambda Sensor: Diagnostic Probe, Heated, Planar probe, Thread pre-greased

• Number of pins: 3
• Sensor Type: Hall Sensor
• Warranty: 5 years warranty
• General Information: Sold in Hueco brand: printing and packaging
• Manufacturer: HUCO

• Quantity: 1
• Cable Length [mm]: 515
• Number of pins: 4
• Name: Detonatsiooniandur
• Manufacturer: DLP

• Number of connectors: 4
• Cable Length [mm]: 535, 435
• Weight [kg]: 0.086
• Manufacturer: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Number of pins: 4
• Manufacturer: FAE

• Engine Code: N53 B30 A, N53B30A
• Required quantity: 1
• Length [mm]: 500
• Cable Length [mm]: 600
• Name: DETONATSIOONIANDUR
• Manufacturer: EPS

• Fitting Position: Left Front, before catalytic converter
• Lambda Sensor: Regulating Probe, Broadband lambda sensor, Heated
• Quantity: 1
• Cable Length [mm]: 1
• Name: DE ES20695-12B1
• Manufacturer: DELPHI

• Housing Type: without housing
• Number of pins: 4
• Connector Shape: oval
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Lambda Sensor: Lambda Sensor
• Weight [kg]: 0.2
• Warranty: 3 years warranty
• Name: CE 09SKV405
• Manufacturer: ESEN SKV

• Lambda Sensor: Lambda Sensor
• Voltage [V]: 12
• Colour: red
• Number of circuits: 5
• Weight [kg]: 0.15
• Operating Mode: Electric
• Warranty: 3 years warranty
• Manufacturer: SKV GERMANY
• Name: CE 09SKV905

• Required quantity: 1
• Voltage [V]: 12
• Number of pins: 4
• Housing Type: without housing
• Manufacturer: BREMI

• Fitting Position: Right Front, before catalytic converter
• Lambda Sensor: Regulating Probe, Broadband lambda sensor, Heated
• Quantity: 1
• Cable Length [mm]: 910
• Name: DE ES21275-12B1
• Manufacturer: DELPHI

• Engine Code: N53 B30 A
• Colour: black
• Number of pins: 3
• only in connection with: 13 62 7 530 413
• Bolt Head-/Nut Design: Male Torx
• Name: Andur, v„ntvoll
• Manufacturer: VDO

• Lambda Sensor: Regulating Probe
• Fitting Position: before catalytic converter, for cylinder 4-6
• Number of circuits: 5
• Overall Length [mm]: 910
• Recommended change interval [km]: 250,000
• Name: LAMBDA ANDUR
• Manufacturer: BOS

• Engine Code: N53 B30 A, N53B30A
• Fitting Position: Left Front, before catalytic converter
• Required quantity: 1
• Length [mm]: 1,400
• Cable Length [mm]: 1,500
• Conductor Number: 5
• Number of circuits: 5
• Name: EP 1.998.482
• Manufacturer: EPS

Lambda Sensor: Regulating Probe, Heated, Planar probe, Broadband lambda sensor, Thread pre-greased

• Lambda Sensor: Lambda Sensor
• Weight [kg]: 0.15
• Warranty: 3 years warranty
• Technical Information: Universal
• Name: CE 09SKV915
• Manufacturer: ESEN SKV

• Lambda Sensor: Diagnostic Probe
• Fitting Position: after catalytic converter, for cylinder 1-3
• Number of circuits: 4
• Overall Length [mm]: 540
• Recommended change interval [km]: 160,000
• Name: LAMBDA ANDUR
• Manufacturer: BOS

• Lambda Sensor: Regulating Probe
• Fitting Position: before catalytic converter, for cylinder 1-3
• Number of circuits: 5
• Overall Length [mm]: 1,400
• Recommended change interval [km]: 250,000
• Name: LAMBDA ANDUR
• Manufacturer: BOS

• Lambda Sensor: Broadband lambda sensor
• Number of pins: 5
• Cable Length [mm]: 1,290
• for article number: 81668E
• Quality: OE EQUIVALENT
• Manufacturer: MEAT&DORIA

• Lambda Sensor: Diagnostic Probe
• Fitting Position: after catalytic converter, for cylinder 4-6
• Number of circuits: 4
• Overall Length [mm]: 495
• Recommended change interval [km]: 160,000
• Name: LAMBDA ANDUR
• Manufacturer: BOS

• Fitting Position: before catalytic converter
• Number of pins: 6
• Cable Length [mm]: 950
• Thread Size: M18x1,5
• Switch Pressure [bar]: 4
• Weight [kg]: 0.18
• Manufacturer: VALEO
• Name: VA 368430

Lambda Sensor: Planar probe, Broadband lambda sensor, Thread pre-greased, Heated

• Line insulation design: with silicone-coated woven-fibre insulation
• Cable Length [mm]: 1,405
• Thread Size: M18 x 1,5
• Conductor Number: 5
• Connector Shape: D Shape
• Length [mm]: 1,250
• Number of pins: 5
• Lambda Sensor: Regulating Probe, Thread pre-greased
• Number of circuits: 5
• Exhaust System: after catalytic converter
• Weight [kg]: 0.188
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.