• Fitting Position: Front Axle, Upper
• Fabrication Number: ZTP-BM-013A

• Fitting Position: Front Axle, Centre
• Mounting Type: Rubber-Metal Mount
• Control/Trailing Arm Type: for control arm
• Height [mm]: 55
• Weight [kg]: 0.22
• Name: DY 37-26724
• Manufacturer: DYS

• Thickness [mm]: 52, 31.5
• Inner Diameter [mm]: 10.3
• Outer Diameter [mm]: 53, 39.4
• Material: Aluminium
• Fitting Position: Upper, Front Axle Left, Front Axle Right
• Mounting Type: Rubber-Metal Mount
• Weight [kg]: 0.5
• Camber correction [degree]: 0
• Manufacturer: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Fitting Position: Front Axle, Rear, Lower
• Inner Diameter [mm]: 15
• Outer Diameter [mm]: 56
• for OE number: Part of 31126794203
• paired article number: 2256095
• Manufacturer: SASIC

• Fitting Position: Front Axle, Front, Lower
• Inner Diameter [mm]: 15
• Outer Diameter [mm]: 43
• for OE number: Part of 31126794203
• paired article number: 2256094
• Manufacturer: SASIC

• Height [mm]: 55
• Outer Diameter [mm]: 43
• Control/Trailing Arm Type: for control arm
• Mounting Type: Rubber-Metal Mount
• Weight [kg]: 0.312
• Material: Rubber/Metal
• Inner Diameter [mm]: 14
• Fitting Position: both sides, Front Axle
• Axle alignment required after fitting:
• Manufacturer: VAICO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Fitting Position: Left, Upper, Right, Front Axle
• Material: Rubber/Metal
• Weight [g]: 95
• Inner Diameter [mm]: 38
• Outer Diameter [mm]: 52
• Length [mm]: 10
• Overall Length [mm]: 51.8
• Name: IM 1351
• Manufacturer: ORIGINAL IMPERIUM

• Fitting Position: Lower Front Axle, outer
• Weight [kg]: 0.252
• Packaging length [cm]: 5.5
• Packaging width [cm]: 4.3
• Packaging height [cm]: 4.3
• Manufacturer: FEBEST

• Fitting Position: behind the axle, Lower Front Axle, inner
• Fabrication Number: ZTP-BM-012A

• Outer Diameter [mm]: 43
• Inner Diameter [mm]: 14
• Width [mm]: 41
• Mounting Type: Rubber-Metal Mount
• Quantity per axle: 2
• for OE number: 3112 6 794 203, 3112 6 794 204
• Manufacturer: TOPRAN HANS PRIES

Fitting Position: Front Axle Left, Front Axle Right, Lower, Rear, outer General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Inner Diameter 1 [mm]: 14
• Outer Diameter 1 [mm]: 51
• Thickness 1 [mm]: 60
• Manufacturer: DELPHI
• Name: DE TD1746W

Fitting Position: Rear Axle, in front of axle, both sides, inner, Upper

• Fitting Position: Front Axle
• Inner Diameter 1 [mm]: 10
• Outer Diameter 1 [mm]: 40
• Thickness 1 [mm]: 52
• Manufacturer: DELPHI

• Length [mm]: 55
• Inner Diameter [mm]: 14
• Outer Diameter [mm]: 43
• Mounting Type: Rubber-Metal Mount
• Weight [kg]: 0.297
• Manufacturer: FEB

Fitting Position: Front Axle Left, Front Axle Right, Rear, outer, Lower General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions. Name: Puks - K„„ndmik BMW P. F10/11 520-550 10- LE/PR TYLNA

• Fitting Position: Front Axle, Lower, Rear, inner, both sides
• Mounting Type: Rubber-Metal Mount
• Control/Trailing Arm Type: for control arm
• Material: Rubber/Metal
• Required quantity: 2
• Name: Puks
• Manufacturer: TED

• Fitting Position: Front Axle, Upper, inner, Front, Rear, both sides
• Mounting Type: Rubber-Metal Mount
• Quantity per axle: 4
• Article number of recommended accessories: 37471 01
• Manufacturer: LMI

SVHC: No information available, please contact the manufacturer! Name: Puks - K„„ndmik BMW P. F10/11 520D-550 10- /F12/13 640-650 10-/ F01-04 730-760 10-

• Fitting Position: Centre
• Control/Trailing Arm Type: for control arm
• Mounting Type: Rubber-Metal Mount
• Manufacturer: CORTECO
• Name: COC 49398288

• Length [mm]: 44
• Width [mm]: 48.4
• Thickness [mm]: 44
• Inner Diameter [mm]: 12
• Outer Diameter [mm]: 48.4
• Material: Rubber/Metal
• Fitting Position: Rear Axle Left, Rear Axle Right, Centre
• Weight [kg]: 0.12
• Manufacturer: FEBI

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Fitting Position: Rear Axle, outer, Upper, Front
• Inner Diameter 1 [mm]: 14
• Outer Diameter 1 [mm]: 52
• Thickness 1 [mm]: 61
• Name: DE TD1712W
• Manufacturer: DELPHI

• Height [mm]: 52
• Inner Diameter [mm]: 10
• Outer Diameter [mm]: 40
• Supplementary Article/Supplementary Info: without holder
• reinforced version:
• Required quantity: 4
• Replace in pairs only:
• with environmental seal: Carbon neutral
• Manufacturer: MEY

Fitting Position: Front Axle Right, Front Axle Left, Rear, Front, Upper General Information: No risk of leakage: MEYLE-HD full-rubber bushing with optimized rubber shape for a significantly longer lifetime. Name: Puks - K„„ndmik BMW P. F10/11 520D-550 10- /F12/13 640-650 10-/ F01-04 730-760 10-

• Fitting Position: outer, Rear, Front Axle Left, Front Axle Right
• Height [mm]: 55
• Inner Diameter [mm]: 14
• Outer Diameter [mm]: 43
• Supplementary Article/Supplementary Info: without holder
• Required quantity: 2
• replacement in pairs recommended:
• Manufacturer: MEY

Name: Puks - K„„ndmik BMW P. 5 (F10, F11) (03/10-12/11), 6 (F12, F13) (11/10-12/12) LE/PR

• Fitting Position: Front Axle, Upper
• Weight [kg]: 0.107
• Packaging length [cm]: 5.3
• Packaging width [cm]: 5.3
• Packaging height [cm]: 5.2
• Manufacturer: FEBEST

• Length [mm]: 89.5
• Inner Diameter [mm]: 15
• Outer Diameter [mm]: 56
• Fitting Position: Front Axle Left, Rear, Front Axle Right
• Weight [kg]: 0.297
• Manufacturer: FEBI

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Fitting Position: Rear Axle, both sides, Rear, inner
• Mounting Type: Rubber-Metal Mount
• Control/Trailing Arm Type: for control arm
• Outer Diameter [mm]: 44
• Inner Diameter [mm]: 12
• Height [mm]: 29
• Required quantity: 2
• Warranty: 3 years warranty or until 75,000km
• Manufacturer: METZGER

• Fitting Position: Lower Front Axle, Front, both sides, inner
• Required quantity: 2
• Manufacturer: TEDGUM

• Length [mm]: 89.5
• Inner Diameter [mm]: 15
• Outer Diameter [mm]: 56
• Fitting Position: Front Axle Left, Rear, Front Axle Right
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Fitting Position: Front Axle, Lower, Rear, outer, both sides
• Mounting Type: Rubber-Metal Mount
• Quantity per axle: 2
• Article number of recommended accessories: 38312 01, 42760 01, 43450 01, 44826 01
• Observe service information:
• Manufacturer: LMI

SVHC: No information available, please contact the manufacturer! Name: Puks - K„„ndmik BMW P. F10/11 520-550 10- LE/PR TYLNA

• Fitting Position: Rear Axle Lower
• Weight [kg]: 0.383
• Packaging length [cm]: 7
• Packaging width [cm]: 6.7
• Packaging height [cm]: 6.7
• Manufacturer: FEBEST

• Fitting Position: Rear Axle Lower, inner
• Weight [kg]: 0.268
• Packaging length [cm]: 7.4
• Packaging width [cm]: 7.4
• Packaging height [cm]: 7.1
• Manufacturer: FEBEST

• Fitting Position: Rear, Left, Right, Lower, Front Axle
• Material: Rubber/Metal
• Control/Trailing Arm Type: for trailing arm
• Weight [g]: 260
• Inner Diameter [mm]: 14
• Outer Diameter [mm]: 56
• Length [mm]: 53
• Overall Length [mm]: 70.9
• Name: IM 1362
• Manufacturer: ORIGINAL IMPERIUM

• Fitting Position: Front Axle, Lower, Front, inner, both sides
• Mounting Type: Rubber-Metal Mount
• Manufacturer: MAX

Name: Puks - K„„ndmik BMW P. 5 F10/6 F13 10- DOLNEGO LE/PR PRZEDNIA WEWN.

• Fitting Position: Rear Axle Right, Rear Axle Left, Front, inner
• Height [mm]: 70
• Inner Diameter [mm]: 14
• Outer Diameter [mm]: 58
• Supplementary Article/Supplementary Info: without holder
• reinforced version:
• Required quantity: 2
• Quantity per axle: 2
• Replace in pairs only:
• Name: Laagripuks, ootshoob
• Manufacturer: MEY

General Information: Improved design for longer service life: MEYLE-HD parts deliver enhanced durability. Compared to OE, MEYLE-HD is technically improved with reinforced inner parts, using higher quality materials or optimized design solution.

• Thickness [mm]: 86
• Inner Diameter [mm]: 14
• Outer Diameter [mm]: 70
• Material: Aluminium
• Fitting Position: Front Axle Left, Front Axle Right, Lower, Front
• Mounting Type: Rubber-Metal Mount
• Weight [kg]: 0.35
• Observe service information:
• Manufacturer: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Fitting Position: Rear Axle, Front, inner, both sides
• Article number of recommended accessories: 37898 01
• Observe service information:
• Manufacturer: LMI

SVHC: No information available, please contact the manufacturer! Name: Puks - K„„ndmik BMW T. 5 F10/ 6 F12/ 7 F01 08- LE/PR

• Fitting Position: Rear Axle, both sides, Rear, inner
• Mounting Type: Rubber-Metal Mount
• Control/Trailing Arm Type: for control arm
• Outer Diameter [mm]: 60
• Inner Diameter [mm]: 14
• Height [mm]: 50
• Warranty: 3 years warranty or until 75,000km
• Manufacturer: METZGER

• Thickness [mm]: 86
• Inner Diameter [mm]: 14
• Outer Diameter [mm]: 70
• Material: Aluminium
• Fitting Position: Front Axle Left, Front Axle Right, Lower, Front
• Mounting Type: Rubber-Metal Mount
• Observe service information:
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Fitting Position: Rear Axle, Front, outer, both sides
• Article number of recommended accessories: 37898 01
• Observe service information:
• Name: Puks - K„„ndmik BMW T. 5 F10/ 6 F12/ 7 F01 08-
• Manufacturer: LMI

SVHC: No information available, please contact the manufacturer!

• Fitting Position: Rear Axle Left, Rear Axle Right, Rear, inner
• Height [mm]: 70
• Inner Diameter [mm]: 14
• Outer Diameter [mm]: 66
• Supplementary Article/Supplementary Info: without holder
• reinforced version:
• Required quantity: 2
• Quantity per axle: 2
• Replace in pairs only:
• Name: Laagripuks, ootshoob
• Manufacturer: MEY

General Information: Improved design for longer service life: MEYLE-HD parts deliver enhanced durability. Compared to OE, MEYLE-HD is technically improved with reinforced inner parts, using higher quality materials or optimized design solution.

• Height [mm]: 90
• Inner Diameter [mm]: 14
• Outer Diameter [mm]: 56
• Supplementary Article/Supplementary Info: without holder
• Required quantity: 2
• replacement in pairs recommended:
• Manufacturer: MEY

Fitting Position: inner, Rear, Lower, Front Axle Left, Front Axle Right Name: Puks - K„„ndmik BMW P. F10/11 520-550 10- / F01-04 730D-760I 08- LE/PR TYLNA WEWN.

• Fitting Position: Front Axle
• Inner Diameter 1 [mm]: 15
• Outer Diameter 1 [mm]: 56
• Thickness 1 [mm]: 90
• Manufacturer: DELPHI
• Name: DE TD962W

• Fitting Position: Front, Lower, Front Axle Left, Front Axle Right
• Height [mm]: 86
• Inner Diameter [mm]: 14
• Outer Diameter [mm]: 70
• Supplementary Article/Supplementary Info: without holder
• Required quantity: 2
• replacement in pairs recommended:
• Manufacturer: MEY

Name: Puks - K„„ndmik BMW P. 5 F10/6 F13 10- DOLNEGO LE/PR PRZEDNIA WEWN.

• Fitting Position: Front Axle, Lower, Front, inner, both sides
• Mounting Type: Rubber-Metal Mount
• Quantity per axle: 2
• Article number of recommended accessories: 38228 01, 38229 01
• Observe service information:
• Manufacturer: LMI
• Lisainfo: 35387 01 LEM
• Additional information: 35387 01 LEM

SVHC: No information available, please contact the manufacturer! Name: Puks - K„„ndmik BMW P. 5 F10/6 F13 10- DOLNEGO LE/PR PRZEDNIA WEWN.

• Fitting Position: Front Axle, Rear, outer, Lower
• Inner Diameter 1 [mm]: 16
• Outer Diameter 1 [mm]: 58
• Thickness 1 [mm]: 60
• Manufacturer: DELPHI
• Name: DE TD1762W

• Fitting Position: inner
• Control/Trailing Arm Type: for control arm
• Mounting Type: Rubber-Metal Mount
• Manufacturer: CORTECO
• Name: COC 49398287

• Fitting Position: Rear Axle Lower, outer
• Weight [kg]: 0.57
• Packaging length [cm]: 7
• Packaging width [cm]: 6.5
• Packaging height [cm]: 6.5
• Manufacturer: FEBEST

• Fitting Position: Rear Axle Left, Rear Axle Right
• Height [mm]: 60.3
• Inner Diameter [mm]: 16.1
• Outer Diameter [mm]: 52
• Supplementary Article/Supplementary Info: without holder
• Supplementary Article/Info 2: without retaining ring
• Required quantity: 2
• replacement in pairs recommended:
• Name: Puks - K„„ndmik BMW T. 5 F10/11 10-
• Manufacturer: MEY

• Length [mm]: 60
• Inner Diameter [mm]: 16
• Outer Diameter [mm]: 52
• Weight [kg]: 0.555
• Supplementary Article/Info 2: with retaining ring
• Name: Puks - K„„ndmik BMW T. 5 F10/11 10-
• Manufacturer: FEB

Fitting Position: Rear Axle Left, Lower, outer, Rear Axle Right, Rear General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Length [mm]: 60
• Inner Diameter [mm]: 16
• Outer Diameter [mm]: 52
• Weight [kg]: 0.555
• Supplementary Article/Info 2: with retaining ring
• Manufacturer: SWAG

Fitting Position: Rear Axle Left, Lower, outer, Rear Axle Right, Rear General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Fitting Position: outer, Rear Axle Left, Rear Axle Right
• Height [mm]: 60.3
• Inner Diameter [mm]: 16.1
• Outer Diameter [mm]: 52
• Mounting Type: Molecular Bearing
• Supplementary Article/Supplementary Info: without holder
• Supplementary Article/Info 2: with retaining ring
• Required quantity: 2
• replacement in pairs recommended:
• Name: Puks
• Manufacturer: MEY