• Fitting Position: frontal sided
• Inner Diameter [mm]: 35
• Outer Diameter [mm]: 48
• Width [mm]: 10
• Material: FPM (fluoride rubber)
• Manufacturer: JP GROUP
• Lisainfo: Oil seal, 35x48x10 mm
• Additional information: Oil seal, 35x48x10 mm

• Fitting Position: frontal sided
• Outer Diameter [mm]: 47
• Inner Diameter [mm]: 32
• Width [mm]: 10
• Manufacturer: JP GROUP
• Lisainfo: PAKENDIS 10 tk
• Additional information: PAKENDIS 10 tk

• Fitting Position: frontal sided
• Inner Diameter [mm]: 35
• Outer Diameter [mm]: 48
• Width [mm]: 10
• Manufacturer: JP GROUP
• Lisainfo: Oil seal, 35x48x10
• Additional information: Oil seal, 35x48x10

Material: PTFE (polytetrafluoroethylene)/ACM (polyacrylate rubber)

• Material: ACM (Polyacrylate)
• Fitting Position: frontal sided
• Thickness [mm]: 10
• Weight [kg]: 0.016
• Required quantity: 1
• Inner Diameter [mm]: 35
• Outer Diameter [mm]: 48
• General Information: seal ring;35*48*10 mm
• Manufacturer: VIKA

• Fitting Position: Front
• Inner Diameter [mm]: 35
• Outer Diameter [mm]: 48
• Height [mm]: 10
• Fabrication Number: NUP-VW-012

• Engine Code: AQD, APR, AMX, ALG
• Vehicle Identification Number (VIN) to: 4B-Y-036000
• Inner Diameter [mm]: 35
• Outer Diameter [mm]: 48
• Height [mm]: 10
• Dust Cover: with dust lip
• Swirl Type: Right-hand Twist
• Material: FPM (fluoride rubber)/ACM (polyacrylate rubber)
• Fitting Position: frontal sided
• Name: VOLLI RONGASTIHEND, OLIPUMP
• Manufacturer: HAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Fitting Position: frontal sided, transmission sided
• Height [mm]: 11
• Material: FPM (fluoride rubber)
• Inner Diameter [mm]: 85
• Outer Diameter [mm]: 105
• Swirl Type: Left-hand Twist
• Dust Cover: with dust lip
• Manufacturer: DELLO AUTOMEGA

• Required quantity: 4
• Thickness [mm]: 10
• for OE number: 068 103 085 E
• Fitting Position: frontal sided
• Inner Diameter [mm]: 32
• Outer Diameter [mm]: 47
• Weight [kg]: 0.023
• Manufacturer: VAICO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Engine Code: AQD, APR, AMX, ALG
• Fitting Position: frontal sided
• Vehicle Identification Number (VIN) from: 4B-Y-036001
• Inner Diameter [mm]: 35
• Outer Diameter [mm]: 48
• Height [mm]: 10
• Dust Cover: with dust lip
• Manufacturer: TOPRAN HANS PRIES

Material: PTFE (polytetrafluoroethylene)/ACM (polyacrylate rubber) General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Inner Diameter [mm]: 32
• Outer Diameter [mm]: 47
• Height [mm]: 10
• Dust Cover: with dust lip
• Swirl Type: Alternating Twist
• Material: FPM (fluoride rubber)
• Fitting Position: frontal sided
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Vehicle Identification Number (VIN) to: 4B-Y-036 000
• Thickness [mm]: 10
• Inner Diameter [mm]: 35
• Outer Diameter [mm]: 48
• Material: ACM (Polyacrylate)
• Fitting Position: frontal sided
• Weight [kg]: 0.016
• Manufacturer: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Fitting Position: frontal sided
• Engine Code: AMX
• Material: FPM (fluoride rubber)
• Inner Diameter [mm]: 35
• Outer Diameter [mm]: 48
• Height [mm]: 10
• Radial Shaft Seal Design: A SL
• Swirl Type: Right-hand Twist
• Name: VOLLI RONGASTIHEND, VŽNTVOLL
• Manufacturer: REI

• Fitting Position: frontal sided
• Inner Diameter [mm]: 35
• Outer Diameter [mm]: 48
• Height [mm]: 10
• Radial Shaft Seal Design: ASW
• Swirl Type: Right-hand Twist
• Material: FPM (fluoride rubber)
• Dust Cover: with dust lip
• Manufacturer: ELRING

• Engine Code: APR, ALG, AQD
• Vehicle Identification Number (VIN) to: -> 4BY036000
• Block Separation:
• Fitting Position: frontal sided
• Inner Diameter 1 [mm]: 35
• Outer Diameter 1 [mm]: 48
• Height 1 [mm]: 10
• Material: FPM (fluoride rubber)
• Dust Cover: with dust lip
• Swirl Type: Right-hand Twist
• for OE number: 034115137A
• Name: VOLLI RONGASTIHEND, OLIPUMP
• Manufacturer: COT

• Engine Code: ACK, ALG
• Inner Diameter [mm]: 35
• Thickness [mm]: 10
• Outer Diameter [mm]: 48
• Fitting Position: frontal sided
• for OE number: 054 115 147 B
• Weight [kg]: 0.02
• Material: FPM (fluoride rubber)
• Manufacturer: VAICO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Fitting Position: frontal sided
• Height [mm]: 10
• Inner Diameter [mm]: 35
• Outer Diameter [mm]: 48

• Engine Code: AMX, APR, AQD, ALG
• Vehicle Identification Number (VIN) to: 4B-Y-036000
• Fitting Position: frontal sided
• Height [mm]: 10
• Inner Diameter [mm]: 35
• Outer Diameter [mm]: 48
• Swirl Type: Right-hand Twist
• Radial Shaft Seal Design: ASW
• Manufacturer: DR MOTOR PRZEWODY PRZELEWOWE

• Fitting Position: frontal sided
• Inner Diameter [mm]: 35
• Outer Diameter [mm]: 48
• Height [mm]: 10
• Radial Shaft Seal Design: ASW
• Swirl Type: Right-hand Twist
• Material: FPM (fluoride rubber)/ACM (polyacrylate rubber)
• Dust Cover: with dust lip
• Manufacturer: ELRING

• Fitting Position: transmission sided
• Inner Diameter [mm]: 85
• Outer Diameter [mm]: 105
• Width [mm]: 11
• Name: Volli rongastihend, V„ntvoll
• Manufacturer: DRM

• Fitting Position: frontal sided
• Height [mm]: 10
• Inner Diameter [mm]: 32
• Outer Diameter [mm]: 47
• Swirl Type: Right-hand Twist
• Manufacturer: DR MOTOR PRZEWODY PRZELEWOWE

• Construction Year to: 05.2001
• Fitting Position: frontal sided
• Height [mm]: 10
• Outer Diameter 1 [mm]: 48
• Inner Diameter 1 [mm]: 35
• Manufacturer: BGA

• Fitting Position: transmission sided
• Inner Diameter [mm]: 85
• Outer Diameter [mm]: 105
• Height [mm]: 11
• Radial Shaft Seal Design: ASW
• Swirl Type: Left-hand Twist
• Material: FPM (fluoride rubber)
• Dust Cover: with dust lip
• Alternative Repair Kit: 829.056
• Manufacturer: ELRING
• Lisainfo: 342.093 ELR
• Additional information: 342.093 ELR

• Fitting Position: frontal sided
• Block Separation:
• Engine Code: ACK, ALG, AMX, AQD, APR, ATQ
• Construction Year to: 07.1998, 05.2001
• Engine Number to: 4BY036000
• Inner Diameter [mm]: 35
• Outer Diameter [mm]: 48
• Height [mm]: 10
• Swirl Type: Right-hand Twist
• Name: VOLLI RONGASTIHEND, VŽNTVOLL
• Manufacturer: AJU

• Thickness [mm]: 11
• Inner Diameter [mm]: 85
• Outer Diameter [mm]: 105
• Fitting Position: transmission sided
• Weight [kg]: 0.103
• Manufacturer: VAICO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Fitting Position: frontal sided
• Height [mm]: 10
• Inner Diameter [mm]: 35
• Outer Diameter [mm]: 48
• Swirl Type: Right-hand Twist
• Radial Shaft Seal Design: ASW
• Manufacturer: DR MOTOR PRZEWODY PRZELEWOWE

• Fitting Position: frontal sided
• Inner Diameter [mm]: 35
• Outer Diameter [mm]: 48
• Height [mm]: 10
• Radial Shaft Seal Design: ASW
• Swirl Type: Right-hand Twist
• Dust Cover: with dust lip
• Supplementary Article/Info 2: with mounting sleeve
• Observe mounting information:
• Manufacturer: ELRING
• Lisainfo: 155.560 ELR
• Additional information: 155.560 ELR

Material: PTFE (polytetrafluoroethylene)/ACM (polyacrylate rubber) Installation Information: Mounting dry and without any additional oil and grease

• Engine Code: AMX
• Fitting Position: frontal sided
• Inner Diameter 1 [mm]: 35
• Outer Diameter 1 [mm]: 48
• Height 1 [mm]: 10
• Material: PTFE (polytetrafluoroethylene)
• Swirl Type: Right-hand Twist
• Dust Cover: with dust lip
• Supplementary Article/Info 2: with mounting sleeves
• for OE number: 038103085
• Name: VOLLI RONGASTIHEND, VŽNTVOLL
• Manufacturer: COT
• Additional information: 20026412B COR
• Lisainfo: 20026412B COR

• Fitting Position: frontal sided
• Engine Code: ATQ
• Material: PTFE (polytetrafluoroethylene), ACM (Polyacrylate)
• Supplementary Article/Info 2: with mounting sleeve
• Inner Diameter [mm]: 35
• Outer Diameter [mm]: 48
• Height [mm]: 10
• Radial Shaft Seal Design: A SL
• Swirl Type: Right-hand Twist
• Name: VOLLI RONGASTIHEND, VŽNTVOLL
• Manufacturer: REI

• Engine Code: AMX, ATQ, AQD
• Block Separation:
• Vehicle Identification Number (VIN) from: 4B-Y-036 001
• Thickness [mm]: 10
• Inner Diameter [mm]: 35
• Outer Diameter [mm]: 48
• Fitting Position: frontal sided
• Weight [kg]: 0.01
• Observe service information:
• Manufacturer: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Fitting Position: frontal sided
• Block Separation:
• Engine Code: AMX, AQD, APR
• Construction Year to: 05.2001
• Inner Diameter [mm]: 35
• Outer Diameter [mm]: 48
• Height [mm]: 10
• Swirl Type: Right-hand Twist
• Name: VOLLI RONGASTIHEND, VŽNTVOLL
• Manufacturer: AJU

• Fitting Position: transmission sided
• Inner Diameter [mm]: 85
• Outer Diameter [mm]: 105
• Height [mm]: 11
• Radial Shaft Seal Design: ASW
• Swirl Type: Left-hand Twist
• Material: FPM (fluoride rubber)
• Dust Cover: with dust lip
• Supplementary Article/Info 2: with mounting sleeve
• Manufacturer: ELRING

• Fitting Position: transmission sided
• Inner Diameter [mm]: 85
• Outer Diameter [mm]: 105
• Height [mm]: 12
• Radial Shaft Seal Design: AW/BS
• Swirl Type: Left-hand Twist
• Dust Cover: with dust lip
• Observe mounting information:
• Supplementary Article/Info 2: with mounting sleeve
• Name: Rongastihend
• Manufacturer: ELR

Material: PTFE (polytetrafluoroethylene)/ACM (polyacrylate rubber) Installation Information: Mounting dry and without any additional oil and grease

• Axle Code: 656.317
• Fitting Position: transmission sided
• Inner Diameter 1 [mm]: 85
• Outer Diameter 1 [mm]: 105
• Height 1 [mm]: 12
• Dust Cover: with dust lip
• Swirl Type: Left-hand Twist
• Supplementary Article/Info 2: with mounting sleeves
• Name: VOLLI RONGASTIHEND, VŽNTVOLL
• Manufacturer: COT

Material: PTFE (polytetrafluoroethylene)/ACM (polyacrylate rubber)

• Engine Code: AMX, ATQ, AQD
• Block Separation:
• Vehicle Identification Number (VIN) from: 4B-Y-036 001
• for OE number: 03G 105 021 C
• Thickness [mm]: 10
• Inner Diameter [mm]: 35
• Fitting Position: frontal sided
• Outer Diameter [mm]: 48
• Weight [kg]: 0.031
• Manufacturer: VAICO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Outer Diameter [mm]: 47
• Thickness [mm]: 10
• Inner Diameter [mm]: 32
• Fitting Position: transmission sided
• Weight [kg]: 0.195
• Manufacturer: VAICO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Fitting Position: transmission sided
• Supplementary Article/Info 2: with flange
• Weight [kg]: 0.418
• Required quantity: 1
• Inner Diameter [mm]: 85
• General Information: seal ring
• Manufacturer: VIKA

• Inner Diameter [mm]: 85
• Material: PTFE (polytetrafluoroethylene)
• Fitting Position: transmission sided
• Weight [kg]: 0.418
• Supplementary Article/Info 2: with flange
• Observe service information:
• Name: VOLLI RONGASTIHEND, VŽNTVOLL
• Manufacturer: FEB

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Fitting Position: transmission sided
• Inner Diameter 1 [mm]: 85
• Outer Diameter 1 [mm]: 158.2
• Outer Diameter 2 [mm]: 235
• Height 1 [mm]: 14.3
• Supplementary Article/Info 2: with flange, with mounting sleeves
• for OE number: 078103171L
• Manufacturer: CORTECO
• Name: CO 19036697

Material: TFE (tetrafluorethylene)/ACM (polyacryl-rubber)/non-woven