• Cable Length [mm]: 1,025
• Fitting Position: Front Axle Left, Front Axle Right
• Fabrication Number: HCA-AU-007
• Manufacturer: NTY

• Fitting Position: Front Axle Left, Front Axle Right
• Sensor Type: Passive sensor
• Length [mm]: 1,100
• Manufacturer: JP GROUP
• Lisainfo: ABS sensor, front, left/right
• Additional information: ABS sensor, front, left/right

• Fitting Position: Rear Axle Left, Rear Axle Right
• Sensor Type: Inductive Sensor
• Manufacturer: JP GROUP A/S
• Lisainfo: ABS sensor, rear, left/right
• Additional information: ABS sensor, rear, left/right

• Välisläbimõõt [mm]: 18,8
• Manufacturer: FAST

Üldine informatsioon: 5-year warranty FAST offers up to 5 years warranty on this product, throughout the entire EU. The guarantee covers manufacturing and material defects. In the event of problems, we will refund you for the part or replace it with a new one. Details and warranty restrictions can be found at fastoriginal.eu

• Length [mm]: 32
• Outer Diameter [mm]: 18.8
• Weight [kg]: 0.005
• Manufacturer: FEBI BILSTEIN
• Additional information: F15340
• Lisainfo: F15340

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Manufacturer: METZGER

Installatsiooni pool: esisild vasakul, esisild paremal, Tagasild vasakul, Tagasild paremal

• Installatsiooni pool: Esisild
• Hammastehulk: 45
• Siseläbimõõt [mm]: 77
• Jämedus/Tugevus (mm): 11
• Manufacturer: AIC

Üldine informatsioon: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Fitting Position: Front Axle both sides
• Number of Teeth: 45
• Width [mm]: 11
• Inner Diameter [mm]: 77
• Outer Diameter [mm]: 81
• Fabrication Number: NZA-AU-001
• Manufacturer: NTY
• Name: NTY NZA-AU-001
• Lisainfo: 45 T 81 MM / 77 MM / 11 MM
• Additional information: 45 T 81 MM / 77 MM / 11 MM

• Fitting Position: Front Axle both sides
• Width [mm]: 11
• Number of Teeth, ABS ring: 45
• Inner Diameter [mm]: 77
• Outer Diameter [mm]: 80.7
• Weight [kg]: 0.028
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Fitting Position: Rear Axle both sides
• Manufacturer: DELLO AUTOMEGA
• Additional information: 110100510 DELLO
• Lisainfo: 110100510 DELLO

• Fitting Position: Front Axle
• Inner Diameter [mm]: 76.8
• Width [mm]: 11
• Outer Diameter [mm]: 80.7
• Number of Teeth, ABS ring: 45
• Manufacturer: TRISCAN
• Lisainfo: VAG
• Additional information: VAG

• Fitting Position: Rear Axle
• Inner Diameter [mm]: 67
• Width [mm]: 11
• Outer Diameter [mm]: 106.8
• Number of Teeth, ABS ring: 45
• Manufacturer: TRISCAN
• Lisainfo: AUDI
• Additional information: AUDI

• Fitting Position: Rear Axle Left, Rear Axle Right
• Fabrication Number: HCA-AU-005
• Manufacturer: NTY

• Fitting Position: Rear Axle both sides
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Cable Length [mm]: 1,100
• Fitting Position: Front Axle Left, Front Axle Right
• Fabrication Number: HCA-AU-006
• Manufacturer: NTY

• Construction Year to: 07.1998
• for OE number: 8D0 927 803
• Sensor Type: Passive sensor
• Overall Length [mm]: 1,100
• Fitting Position: Front Axle
• Manufacturer: KAMOKA UK£ADY HAMULCOWE

• Construction Year from: 01.1999
• Fitting Position: Front Axle
• Sensor Type: Inductive Sensor
• Number of pins: 2
• Cable Length [mm]: 1,025
• Manufacturer: ABAKUS LORO

General Information: The following information is for general and informational purposes only and does not constitute warranty terms. Warranty terms and conditions are available from our dealers and in our general terms and conditions of sale. Abakus spare/repair parts are intended only for vehicle repairs in order to restore their original functionality. Abakus spare/repair parts are used or sold to users only for the purpose of repairing vehicles to restore their original look and functionality and are not original/genuine/OE/OEM/OES replacement parts. These items do not originate from the vehicle manufacturer and may be the subject of a design not owned by Abakus and the manufacturer of this spare part. They may only be used for repairs to restore the intended vehicle to its original appearance. Our products are delivered without instruction of installation. Installation of our product may only be carried out by trained specialist technicians in specific car repairs. Products supplied by us are exclusively intended for proper and appropriate use. The warranty may become invalid in the event of: improper installation or repair, unsuitable application or use, installation or repair made outside specialist car workshops. Warranty claims are lost if the vehicle is modified and used for motor sports, tuning or similar events (except our tuning parts which are described in TecDoc and on our price list). Warranty application should include complete documentation among others: chassis no., first registration, vehicle mileage, information about LPG installation, fault memory log, pictures, our QC (quality check) code, installation invoice, contact details of the car repair workshop performing the replacement or repair. Warranty application are available in our Client Panel system. Complaints may require supplementing data such as error memory logs. Incomplete documentation may result in rejection of the claim. Any damage caused during transport is not considered quality damage and will be considered on an individual basis. The product is intended for use within the performance limits specified by the manufacturer and should only be used by qualified personnel who have been trained to operate this product. Before each use, the product should be checked for damage or fixing of its parts and not used if any defects or loose parts are found. Failure to follow the manufacturer's guidelines could result in potential product damage or even injury. Wear appropriate protective clothing if necessary when working with the product.

• Fitting Position: Front Axle
• Sensor Type: Inductive Sensor
• Number of pins: 2
• Cable Length [mm]: 1,020
• Manufacturer: ABAKUS LORO

General Information: The following information is for general and informational purposes only and does not constitute warranty terms. Warranty terms and conditions are available from our dealers and in our general terms and conditions of sale. Abakus spare/repair parts are intended only for vehicle repairs in order to restore their original functionality. Abakus spare/repair parts are used or sold to users only for the purpose of repairing vehicles to restore their original look and functionality and are not original/genuine/OE/OEM/OES replacement parts. These items do not originate from the vehicle manufacturer and may be the subject of a design not owned by Abakus and the manufacturer of this spare part. They may only be used for repairs to restore the intended vehicle to its original appearance. Our products are delivered without instruction of installation. Installation of our product may only be carried out by trained specialist technicians in specific car repairs. Products supplied by us are exclusively intended for proper and appropriate use. The warranty may become invalid in the event of: improper installation or repair, unsuitable application or use, installation or repair made outside specialist car workshops. Warranty claims are lost if the vehicle is modified and used for motor sports, tuning or similar events (except our tuning parts which are described in TecDoc and on our price list). Warranty application should include complete documentation among others: chassis no., first registration, vehicle mileage, information about LPG installation, fault memory log, pictures, our QC (quality check) code, installation invoice, contact details of the car repair workshop performing the replacement or repair. Warranty application are available in our Client Panel system. Complaints may require supplementing data such as error memory logs. Incomplete documentation may result in rejection of the claim. Any damage caused during transport is not considered quality damage and will be considered on an individual basis. The product is intended for use within the performance limits specified by the manufacturer and should only be used by qualified personnel who have been trained to operate this product. Before each use, the product should be checked for damage or fixing of its parts and not used if any defects or loose parts are found. Failure to follow the manufacturer's guidelines could result in potential product damage or even injury. Wear appropriate protective clothing if necessary when working with the product.

• Fitting Position: Rear Axle
• Sensor Type: Inductive Sensor
• Number of pins: 2
• Cable Length [mm]: 963
• Manufacturer: ABAKUS LORO

General Information: The following information is for general and informational purposes only and does not constitute warranty terms. Warranty terms and conditions are available from our dealers and in our general terms and conditions of sale. Abakus spare/repair parts are intended only for vehicle repairs in order to restore their original functionality. Abakus spare/repair parts are used or sold to users only for the purpose of repairing vehicles to restore their original look and functionality and are not original/genuine/OE/OEM/OES replacement parts. These items do not originate from the vehicle manufacturer and may be the subject of a design not owned by Abakus and the manufacturer of this spare part. They may only be used for repairs to restore the intended vehicle to its original appearance. Our products are delivered without instruction of installation. Installation of our product may only be carried out by trained specialist technicians in specific car repairs. Products supplied by us are exclusively intended for proper and appropriate use. The warranty may become invalid in the event of: improper installation or repair, unsuitable application or use, installation or repair made outside specialist car workshops. Warranty claims are lost if the vehicle is modified and used for motor sports, tuning or similar events (except our tuning parts which are described in TecDoc and on our price list). Warranty application should include complete documentation among others: chassis no., first registration, vehicle mileage, information about LPG installation, fault memory log, pictures, our QC (quality check) code, installation invoice, contact details of the car repair workshop performing the replacement or repair. Warranty application are available in our Client Panel system. Complaints may require supplementing data such as error memory logs. Incomplete documentation may result in rejection of the claim. Any damage caused during transport is not considered quality damage and will be considered on an individual basis. The product is intended for use within the performance limits specified by the manufacturer and should only be used by qualified personnel who have been trained to operate this product. Before each use, the product should be checked for damage or fixing of its parts and not used if any defects or loose parts are found. Failure to follow the manufacturer's guidelines could result in potential product damage or even injury. Wear appropriate protective clothing if necessary when working with the product.

• Inner Diameter [mm]: 66.8
• Outer Diameter [mm]: 106.8
• Fitting Position: Rear Axle
• Number of Teeth, ABS ring: 45
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Installatsiooni pool: Esisild, esisild paremal, esisild vasakul
• Manufacturer: AUTO-GH

• Construction Year from: 01.1999
• Fitting Position: Front Axle
• Sensor Type: Passive sensor
• Number of pins: 2
• Cable Length [mm]: 1,035
• Manufacturer: ABAKUS LORO

General Information: The following information is for general and informational purposes only and does not constitute warranty terms. Warranty terms and conditions are available from our dealers and in our general terms and conditions of sale. Abakus spare/repair parts are intended only for vehicle repairs in order to restore their original functionality. Abakus spare/repair parts are used or sold to users only for the purpose of repairing vehicles to restore their original look and functionality and are not original/genuine/OE/OEM/OES replacement parts. These items do not originate from the vehicle manufacturer and may be the subject of a design not owned by Abakus and the manufacturer of this spare part. They may only be used for repairs to restore the intended vehicle to its original appearance. Our products are delivered without instruction of installation. Installation of our product may only be carried out by trained specialist technicians in specific car repairs. Products supplied by us are exclusively intended for proper and appropriate use. The warranty may become invalid in the event of: improper installation or repair, unsuitable application or use, installation or repair made outside specialist car workshops. Warranty claims are lost if the vehicle is modified and used for motor sports, tuning or similar events (except our tuning parts which are described in TecDoc and on our price list). Warranty application should include complete documentation among others: chassis no., first registration, vehicle mileage, information about LPG installation, fault memory log, pictures, our QC (quality check) code, installation invoice, contact details of the car repair workshop performing the replacement or repair. Warranty application are available in our Client Panel system. Complaints may require supplementing data such as error memory logs. Incomplete documentation may result in rejection of the claim. Any damage caused during transport is not considered quality damage and will be considered on an individual basis. The product is intended for use within the performance limits specified by the manufacturer and should only be used by qualified personnel who have been trained to operate this product. Before each use, the product should be checked for damage or fixing of its parts and not used if any defects or loose parts are found. Failure to follow the manufacturer's guidelines could result in potential product damage or even injury. Wear appropriate protective clothing if necessary when working with the product.

• Construction Year from: 01.1999
• Fitting Position: Front Axle
• Sensor Type: Inductive Sensor
• Number of pins: 2
• Cable Length [mm]: 1,025
• Manufacturer: ABAKUS

General Information: The following information is for general and informational purposes only and does not constitute warranty terms. Warranty terms and conditions are available from our dealers and in our general terms and conditions of sale. Abakus spare/repair parts are intended only for vehicle repairs in order to restore their original functionality. Abakus spare/repair parts are used or sold to users only for the purpose of repairing vehicles to restore their original look and functionality and are not original/genuine/OE/OEM/OES replacement parts. These items do not originate from the vehicle manufacturer and may be the subject of a design not owned by Abakus and the manufacturer of this spare part. They may only be used for repairs to restore the intended vehicle to its original appearance. Our products are delivered without instruction of installation. Installation of our product may only be carried out by trained specialist technicians in specific car repairs. Products supplied by us are exclusively intended for proper and appropriate use. The warranty may become invalid in the event of: improper installation or repair, unsuitable application or use, installation or repair made outside specialist car workshops. Warranty claims are lost if the vehicle is modified and used for motor sports, tuning or similar events (except our tuning parts which are described in TecDoc and on our price list). Warranty application should include complete documentation among others: chassis no., first registration, vehicle mileage, information about LPG installation, fault memory log, pictures, our QC (quality check) code, installation invoice, contact details of the car repair workshop performing the replacement or repair. Warranty application are available in our Client Panel system. Complaints may require supplementing data such as error memory logs. Incomplete documentation may result in rejection of the claim. Any damage caused during transport is not considered quality damage and will be considered on an individual basis. The product is intended for use within the performance limits specified by the manufacturer and should only be used by qualified personnel who have been trained to operate this product. Before each use, the product should be checked for damage or fixing of its parts and not used if any defects or loose parts are found. Failure to follow the manufacturer's guidelines could result in potential product damage or even injury. Wear appropriate protective clothing if necessary when working with the product.

• Fitting Position: Rear Axle
• Manufacturer: DELLO AUTOMEGA

• Construction Year to: 07.1998
• Sensor Type: Passive sensor
• Overall Length [mm]: 975
• Fitting Position: Rear Axle
• Manufacturer: KAMOKA UK£ADY HAMULCOWE

• Vehicle Identification Number (VIN) to: 8D_X_199999
• Fitting Position: Front Axle
• Sensor Type: Inductive Sensor
• Length [mm]: 1,030
• Manufacturer: DELLO AUTOMEGA

• Vehicle Identification Number (VIN) to: 8D-1-200 000
• Installatsiooni pool: Tagasild vasakul, Tagasild paremal
• Siseläbimõõt [mm]: 67
• Välisläbimõõt [mm]: 107
• Jämedus/Tugevus (mm): 6
• Hammastehulk: 45
• Manufacturer: METZGER

• Installatsiooni pool: esisild mõlemapoolselt
• Ühenduste arv: 2
• Manufacturer: JPN

• Vehicle Identification Number (VIN) from: 8D_X_200001
• Fitting Position: Front Axle
• Manufacturer: DELLO AUTOMEGA

• Inner Diameter [mm]: 67
• Outer Diameter [mm]: 107
• Number of Teeth, ABS ring: 45
• Fitting Position: Rear Axle Left, Rear Axle Right
• Weight [kg]: 0.17
• Manufacturer: FEBI BILSTEIN
• Additional information: F27176
• Lisainfo: F27176

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Installatsiooni pool: Esisild, esisild paremal, esisild vasakul
• Manufacturer: AUTO-GH

• Required quantity: 2
• Fitting Position: Front Axle
• Construction Year to: 04.2001
• Pikkus (mm): 985
• Manufacturer: DENCKERMANN ZAWIESZENIE

• Installatsiooni pool: Tagasild mõlemapoolselt
• Ühenduste arv: 2
• Manufacturer: JPN

• Installatsiooni pool: Tagasild
• Pikkus (mm): 890
• Pistikkontaktide arv: 2
• Pistikute teostus: Male
• Pistikukatte kuju: ristkülik
• Pinge [V]: 12
• Kaal (kg): 0,15
• Värv: must
• Rakendustüüp: elektriline
• Oluline on võrrelda vana uue osaga (eriti OE-numbrit):
• Manufacturer: ENERGY

• Installatsiooni pool: esisild vasakul, esisild paremal
• Hammastehulk ABS-rõngas: 45
• Siseläbimõõt [mm]: 77
• Laius (mm): 11
• Manufacturer: METZGER

• Model Year from: 1999
• Vehicle Identification Number (VIN) from: 8D-X-200 001
• Fitting Position: Front Axle Left, Front Axle Right
• Sensor Type: Passive sensor
• Manufacturer: JP GROUP
• Lisainfo: ABS sensor, front, left/right
• Additional information: ABS sensor, front, left/right

• Sensor Type: Passive sensor
• Number of pins: 2
• Cable Length [mm]: 1,068
• Fitting Position: Front Axle Right, Front Axle Left
• Manufacturer: AUTOFREN SEINSA
• Name: SE DS0016

• Construction Year to: 07.1998
• Installatsiooni pool: Esisild
• Pikkus (mm): 1 040
• Pistikkontaktide arv: 2
• Pistikute teostus: Male
• Pistikukatte kuju: ristkülik
• Pinge [V]: 12
• Kaal (kg): 0,14
• Värv: must
• Rakendustüüp: elektriline
• Oluline on võrrelda vana uue osaga (eriti OE-numbrit):
• Manufacturer: ENERGY

• Vehicle Identification Number (VIN) to: 8D-1-200 000
• Installatsiooni pool: Tagasild mõlemapoolselt
• Hammastehulk: 45
• Siseläbimõõt [mm]: 67
• Välisläbimõõt [mm]: 107
• Manufacturer: AIC

Üldine informatsioon: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Construction Year to: 07.1998
• Fitting Position: Rear Axle
• Resistor [Ohm]: 1,250
• Cable Length [mm]: 880
• for OE number: 8D0927807C
• Number of pins: 2
• Manufacturer: MAGNETI MARELLI

• Installatsiooni pool: Tagasild, Tagasild paremal, Tagasild vasakul
• Manufacturer: AUTO-GH

• Vehicle Equipment: for vehicles with brake pad wear indicator
• Construction Year from: 02.1999
• Fitting Position: Front Axle Left, Front Axle Right
• Supplementary Article/Info 2: with cable
• Length [mm]: 1,031
• Braking/Drive Dynamics: for vehicles with ABS
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Braking/Drive Dynamics: for vehicles without ESP
• Supplementary Article/Info 2: with lid, with sensor
• Material: Plastic
• Observe system fill quantity:
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Fitting Position: Rear Axle
• Length [mm]: 890
• Number of pins: 2
• Plug Type: Male
• Connector Shape: rectangular
• Guarantee: 3 years guarantee
• Voltage [V]: 12
• Weight [kg]: 0.15
• Colour: black
• Operating Mode: Electric
• Always compare old and new part (in particular OE No.):
• Name: CE 06SKV013
• Manufacturer: ESEN SKV

• Construction Year to: 07.1998
• Number of pins: 2
• Connector Shape: rectangular
• Cable Length [mm]: 880
• Overall Length [mm]: 945
• Sensor Type: Inductive Sensor
• Fitting Depth [mm]: 39.3
• Fitting Position: Rear Axle Right, Rear Axle Left
• for OE number: 8D0927807C
• Manufacturer: MEAT&DORIA

• Fabrication Number: CZW-VW-027
• Supplementary Article/Info 2: with lid, with sensor
• Number of connectors: 2
• Material: Plastic
• Observe system fill quantity:
• Manufacturer: NTY

• Model Year from: 1999
• Vehicle Identification Number (VIN) from: 8D-X-200 001
• Fitting Position: Front Axle
• Height [mm]: 1,050, 28
• Braking/Drive Dynamics: for vehicles with ABS
• Rated Voltage [V]: 12
• Length [mm]: 1,060
• Number of connectors: 2
• Multiple: 3
• Supplementary Article/Info 2: with cable
• Required quantity: 2
• Resistor [Ohm]: 1,630
• Cable Length [mm]: 975
• Mounting Type: Bolted
• Sensor Type: Inductive Sensor, Passive sensor
• Number of pins: 2
• Weight [kg]: 0.126
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Construction Year to: 07.1998
• Fitting Position: Front Axle
• Length [mm]: 1,040
• Number of pins: 2
• Plug Type: Male
• Connector Shape: rectangular
• Guarantee: 3 years guarantee
• Voltage [V]: 12
• Weight [kg]: 0.14
• Colour: black
• Operating Mode: Electric
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 06SKV075

• Fitting Position: Front Axle
• Construction Year from: 01.1999
• Vehicle Identification Number (VIN) from: 8D-X-200001
• Sensor Type: Passive sensor
• Number of occupied pins: 2
• Cable Length [mm]: 965
• Manufacturer: DELPHI LOCKHEED HAMULCE
• Name: DE SS20039

• Fitting Position: Front Axle
• Construction Year to: 12.1998
• Vehicle Identification Number (VIN) to: 8D-X-199999
• Sensor Type: Passive sensor
• Number of occupied pins: 2
• Cable Length [mm]: 1,035
• Manufacturer: DELPHI LOCKHEED HAMULCE
• Name: DE SS20004
• Quality class: PJ

• Supplementary Article/Info 2: with lid
• Left-/right-hand drive vehicles: for left-hand drive vehicles
• Manufacturer: JP GROUP
• Lisainfo: Brake fluid tank
• Additional information: Brake fluid tank

• Fitting Position: Front Axle Left, Front Axle Right
• Length [mm]: 1,100
• Sensor Type: Passive sensor
• Weight [kg]: 0.118
• Manufacturer: TOMEX BRAKES

• Fitting Position: Rear Axle
• Sensor Type: Passive sensor
• Number of occupied pins: 2
• Cable Length [mm]: 980
• Name: DE SS20038
• Manufacturer: DELPHI
• Quality class: PJ

• Weight [kg]: 9.5
• New Part:
• Packaging length [cm]: 72.5
• Packaging width [cm]: 59
• Packaging height [cm]: 34

• Construction Year to: 07.1998
• Number of pins: 2
• Connector Shape: rectangular
• Length [mm]: 1,090
• Sensor Type: Inductive Sensor
• Fitting Position: Front Axle Right, Front Axle Left
• for OE number: 8D0927803
• Manufacturer: MEAT & DORIA

• Fitting Position: Rear Axle Right, Rear Axle Left
• Cable Length [mm]: 920
• Number of pins: 2
• Sensor Type: Passive sensor
• Manufacturer: AUTOFREN SEINSA

• Cable Length [mm]: 935
• Sensor Type: Inductive Sensor
• Number of pins: 2
• Fitting Position: Rear Axle
• Manufacturer: FAE

• Fitting Position: Rear Axle
• Overall Length [mm]: 985
• Length [mm]: 40
• Sensor Type: Passive sensor
• Socket colour: black
• Cable Length [mm]: 920
• paired article number: 30005
• Weight [kg]: 0.11
• Manufacturer: A.B.S.

• Required quantity: 2
• Fitting Position: Rear Axle
• Supplementary Article/Info 2: with cable
• Mounting Type: Plug-in connection
• Manufacturer: BREMI

• OE-numbri jaoks: 8E0 611 301
• Laius (mm): 116,6
• Kõrgus (mm): 61
• Pikkus (mm): 165
• Kaal (g): 109
• Garantii: 3 aastat garantii
• Manufacturer: AT AUTOTEILE GERMANY

Üldine informatsioon: Products and spare parts supplied by us are only intended for the designated use. Installation may only be carried out by trained specialist personnel. Our products are not always supplied with installation instructions. Improper installation or inappropriate use may lead to the exclusion of warranty.

• Required quantity: 2
• Fitting Position: Front Axle
• Supplementary Article/Info 2: with cable
• Mounting Type: Plug-in connection
• Manufacturer: BREMI

• Number of connectors: 2
• Fitting Position: Front Axle Left, Front Axle Right
• Weight [kg]: 0.115
• for OE number: 8D0 927 803
• Manufacturer: FEBI HAMULCE

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Supplementary Article/Info 2: with cap
• Manufacturer: ABAKUS

General Information: The following information is for general and informational purposes only and does not constitute warranty terms. Warranty terms and conditions are available from our dealers and in our general terms and conditions of sale. Abakus spare/repair parts are intended only for vehicle repairs in order to restore their original functionality. Abakus spare/repair parts are used or sold to users only for the purpose of repairing vehicles to restore their original look and functionality and are not original/genuine/OE/OEM/OES replacement parts. These items do not originate from the vehicle manufacturer and may be the subject of a design not owned by Abakus and the manufacturer of this spare part. They may only be used for repairs to restore the intended vehicle to its original appearance. Our products are delivered without instruction of installation. Installation of our product may only be carried out by trained specialist technicians in specific car repairs. Products supplied by us are exclusively intended for proper and appropriate use. The warranty may become invalid in the event of: improper installation or repair, unsuitable application or use, installation or repair made outside specialist car workshops. Warranty claims are lost if the vehicle is modified and used for motor sports, tuning or similar events (except our tuning parts which are described in TecDoc and on our price list). Warranty application should include complete documentation among others: chassis no., first registration, vehicle mileage, information about LPG installation, fault memory log, pictures, our QC (quality check) code, installation invoice, contact details of the car repair workshop performing the replacement or repair. Warranty application are available in our Client Panel system. Complaints may require supplementing data such as error memory logs. Incomplete documentation may result in rejection of the claim. Any damage caused during transport is not considered quality damage and will be considered on an individual basis. The product is intended for use within the performance limits specified by the manufacturer and should only be used by qualified personnel who have been trained to operate this product. Before each use, the product should be checked for damage or fixing of its parts and not used if any defects or loose parts are found. Failure to follow the manufacturer's guidelines could result in potential product damage or even injury. Wear appropriate protective clothing if necessary when working with the product.

• Fitting Position: Front Axle
• Overall Length [mm]: 1,065
• Length [mm]: 39
• Sensor Type: Passive sensor
• Socket colour: black
• Cable Length [mm]: 1,000
• paired article number: 30002
• Weight [kg]: 0.12
• Manufacturer: A.B.S.

• Vehicle Identification Number (VIN) to: 8D-X-199 999
• Vehicle Equipment: for vehicles without brake pad wear indicator
• Supplementary Article/Info 2: with ABS sensor ring
• Quantity Unit: Set
• Number of Teeth, ABS ring: 45
• Supplementary Article/Supplementary Info: with gasket/seal
• Fitting Position: Front Axle
• Rated Voltage [V]: 12
• Required quantity: 2
• Resistor [Ohm]: 1,200
• Cable Length [mm]: 1,070
• Sensor Type: Inductive Sensor, Passive sensor
• Number of pins: 2
• Number of connectors: 2
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Fitting Position: Front Axle
• Wear Warning Contact: incl. wear warning contact
• Guarantee: 5 years guarantee
• General Information: Sold in Hueco brand: printing and packaging
• Name: HU 131417
• Manufacturer: HUECO / HITACHI

• Vehicle Identification Number (VIN) to: 8D-X-199999
• Cable Length [mm]: 1,095
• Sensor Type: Inductive Sensor
• Number of pins: 2
• Fitting Position: Front Axle
• Manufacturer: FAE

• Supplementary Article/Info 2: with sensor, with lid
• Weight [kg]: 0.241
• Manufacturer: VAICO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Fitting Position: Rear Axle, Rear Axle Right
• Vehicle Identification Number (VIN) from: 8D-W-280 001
• Required quantity: 2, 1
• Model Year from: 1998, 1989
• Block Separation:
• Vehicle Equipment: for vehicles with headlight levelling (automatic)
• Cable Length [mm]: 925
• Sensor Type: Passive sensor
• Manufacturer: OPTIMAL ZAWIESZENIE

• Vehicle Identification Number (VIN) from: 8D-X-200 001
• Installatsiooni pool: esisild vasakul, esisild paremal
• Manufacturer: METZGER

• Construction Year to: 07.1998
• Fitting Position: Rear Axle
• Sensor Type: Passive sensor
• Supplementary Article/Info 2: with cable
• Overall Length [mm]: 975
• Temperature range from [°C]: -40
• Temperature range to [°C]: 150
• Manufacturer: BOSCH

• Left-/right-hand drive vehicles: for left-hand drive vehicles
• Number of connectors: 2
• Supplementary Article/Info 2: with lid, with sensor
• Weight [kg]: 0.145
• Manufacturer: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Piirangutega toode/piirangu info 2: koos kaanega, koos anduriga
• vasak/paremroolimine: vasakpoolse roolimise jaoks
• Manufacturer: METZGER

• Construction Year to: 07.1998
• Fitting Position: Front Axle
• Sensor Type: Passive sensor
• Supplementary Article/Info 2: with cable
• Overall Length [mm]: 1,100
• Temperature range from [°C]: -40
• Temperature range to [°C]: 150
• Manufacturer: BOSCH

• Fitting Position: Right, Left, Front Axle
• Cable Length [mm]: 1,095
• Manufacturer: SNR /NTN-SNR/