• Fitting Position: frontal sided
• Outer Diameter [mm]: 47
• Inner Diameter [mm]: 32
• Width [mm]: 10
• Manufacturer: JP GROUP A/S
• Lisainfo: PAKENDIS 10 tk
• Additional information: PAKENDIS 10 tk

• Fitting Position: transmission sided
• Inner Diameter [mm]: 85
• Outer Diameter [mm]: 105
• Thickness [mm]: 11
• Material: FPM (fluoride rubber)/ACM (polyacrylate rubber)
• Lisainfo: Oil seal for crankshaft, 85x105x11 mm
• Additional information: Oil seal for crankshaft, 85x105x11 mm

• Engine Code: ADR
• Fitting Position: transmission sided
• Inner Diameter [mm]: 85
• Outer Diameter [mm]: 105
• Width 1 [mm]: 9
• Width 2 [mm]: 11
• Housing Type: with housing
• Lisainfo: Seal flange for crankshaft
• Additional information: Seal flange for crankshaft

• Engine Code: ADR, APT, ARG
• Vehicle Identification Number (VIN) to: -> 8DX199999
• Fitting Position: Front
• Height 1 [mm]: 10
• Outer Diameter 1 [mm]: 47
• Inner Diameter 1 [mm]: 32
• Material: FPM (fluoride rubber)
• for OE number: 026103085D
• Swirl Type: Alternating Twist
• Dust Cover: with dust lip
• Name: CO 12012709
• Manufacturer: CORTECO
• Additional information: 12012709
• Lisainfo: 12012709

• Fitting Position: frontal sided
• Observe service information:
• Swirl Type: Right-hand Twist
• Material: PTFE (polytetrafluoroethylene)
• Dust Cover: with dust lip
• Fabrication Number: NUP-VW-011
• Manufacturer: NTY

• Required quantity: 1
• Fitting Position: frontal sided
• Engine Code: ADR
• Inner Diameter [mm]: 32
• Outer Diameter [mm]: 47
• Width [mm]: 10
• SVHC: No SVHC present!
• Manufacturer: INA

• Fitting Position: frontal sided
• Engine Code: ADR
• Material: FPM (fluoride rubber)
• Inner Diameter [mm]: 32
• Outer Diameter [mm]: 47
• Height [mm]: 10
• Radial Shaft Seal Design: A SL
• Swirl Type: Alternating Twist
• Manufacturer: REINZ
• Lisainfo: 81-19299-10
• Additional information: 81-19299-10

• Fitting Position: frontal sided
• Inner Diameter [mm]: 32
• Outer Diameter [mm]: 47
• Height [mm]: 10
• Radial Shaft Seal Design: ASW
• Swirl Type: Alternating Twist
• Material: FPM (fluoride rubber)/ACM (polyacrylate rubber)
• Dust Cover: with dust lip
• Alternative Repair Kit: 325.156
• Manufacturer: ELRING
• Lisainfo: 325.155 ELR
• Additional information: 325.155 ELR

• Inner Diameter [mm]: 32
• Outer Diameter [mm]: 47
• Height [mm]: 10
• Dust Cover: with dust lip
• Swirl Type: Alternating Twist
• Fitting Position: frontal sided
• Material: FPM (fluoride rubber)
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Engine Code: ADR
• Fitting Position: frontal sided, transmission sided
• Height [mm]: 11
• Material: FPM (fluoride rubber)
• Inner Diameter [mm]: 85
• Outer Diameter [mm]: 105
• Swirl Type: Left-hand Twist
• Dust Cover: with dust lip
• Manufacturer: DELLO AUTOMEGA

• Required quantity: 2
• Thickness [mm]: 10
• for OE number: 068 103 085 E
• Fitting Position: frontal sided
• Inner Diameter [mm]: 32
• Outer Diameter [mm]: 47
• Weight [kg]: 0.023
• Manufacturer: VAICO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Engine Code: ADR
• Fitting Position: frontal sided
• Inner Diameter [mm]: 32
• Outer Diameter [mm]: 47
• Height [mm]: 10
• Swirl Type: Alternating Twist
• Manufacturer: AJUSA

• Fitting Position: frontal sided
• Construction Year from: 02.1999
• Inner Diameter [mm]: 32
• Outer Diameter [mm]: 47
• Height [mm]: 10
• Swirl Type: Alternating Twist, Right-hand Twist
• Dust Cover: with dust lip
• Material: PTFE (polytetrafluoroethylene)
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Fitting Position: frontal sided
• Inner Diameter [mm]: 32
• Outer Diameter [mm]: 47
• Height [mm]: 10
• Radial Shaft Seal Design: ASW
• Swirl Type: Alternating Twist
• Material: FPM (fluoride rubber)
• Dust Cover: with dust lip
• Alternative Repair Kit: 325.155
• Manufacturer: ELRING

• Engine Code: ADR
• Fitting Position: transmission sided
• Inner Diameter [mm]: 85
• Outer Diameter [mm]: 105
• Width [mm]: 11
• Name: DRM 0716
• Manufacturer: DR.MOTOR AUTOMOTIVE

• Engine Code: APT
• Construction Year from: 02.1999
• Fitting Position: frontal sided
• for OE number: MN980030
• Height [mm]: 10
• Material: PTFE (polytetrafluoroethylene)
• Inner Diameter [mm]: 32
• Outer Diameter [mm]: 47
• Rotation Direction: Clockwise rotation
• Manufacturer: FAI

• Fitting Position: frontal sided
• Engine Code: APT, ARG
• Block Separation:
• Material: PTFE (polytetrafluoroethylene), ACM (Polyacrylate)
• Supplementary Article/Info 2: with mounting sleeve
• Inner Diameter [mm]: 32
• Outer Diameter [mm]: 47
• Height [mm]: 10
• Radial Shaft Seal Design: A SL
• Swirl Type: Right-hand Twist
• Manufacturer: REINZ
• Additional information: 81-34367-00 REIN
• Lisainfo: 81-34367-00 REIN

• Fitting Position: frontal sided
• Inner Diameter [mm]: 32
• Outer Diameter [mm]: 47
• Height [mm]: 10
• Radial Shaft Seal Design: ASW
• Swirl Type: Right-hand Twist
• Dust Cover: with dust lip
• Observe mounting information:
• Manufacturer: ELRING
• Lisainfo: 129.780 ELR
• Additional information: 129.780 ELR

Material: PTFE (polytetrafluoroethylene)/ACM (polyacrylate rubber) Installation Information: Mounting dry and without any additional oil and grease

• Engine Code: ADR, APT, ARG
• Vehicle Identification Number (VIN) from: 8DX200001 ->
• Fitting Position: frontal sided
• Height 1 [mm]: 10
• Outer Diameter 1 [mm]: 47
• Inner Diameter 1 [mm]: 32
• Material: PTFE (polytetrafluoroethylene)
• for OE number: 038103085A
• Swirl Type: Right-hand Twist
• Dust Cover: with dust lip
• Manufacturer: CORTECO
• Name: CO 20026413
• Additional information: 20026413
• Lisainfo: 20026413

• Thickness [mm]: 11
• Inner Diameter [mm]: 85
• Outer Diameter [mm]: 105
• Material: FPM (fluoride rubber)
• Fitting Position: transmission sided
• Weight [kg]: 0.058
• Manufacturer: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Fitting Position: transmission sided
• Engine Code: ADR
• Inner Diameter [mm]: 85
• Outer Diameter [mm]: 105
• Height [mm]: 11
• Radial Shaft Seal Design: ASW
• Swirl Type: Left-hand Twist
• Material: FPM (fluoride rubber)
• Dust Cover: with dust lip
• Alternative Repair Kit: 829.056
• Manufacturer: ELRING
• Lisainfo: 342.093 ELR
• Additional information: 342.093 ELR

• Fitting Position: transmission sided
• Engine Code: ADR
• Material: FPM (fluoride rubber)
• Inner Diameter [mm]: 85
• Outer Diameter [mm]: 105
• Height [mm]: 11
• Radial Shaft Seal Design: A SL
• Swirl Type: Left-hand Twist
• Height 1 [mm]: 9
• Manufacturer: REINZ
• Name: RN 81-23708-40
• Lisainfo: 81-23708-40
• Additional information: 81-23708-40

• Thickness [mm]: 10
• Inner Diameter [mm]: 32
• Outer Diameter [mm]: 47
• Rotation Direction: Clockwise rotation
• Material: ACM (Polyacrylate), PTFE (polytetrafluoroethylene)
• Supplementary Article/Info 2: with mounting sleeve
• Fitting Position: frontal sided
• Weight [kg]: 0.01
• Observe service information:
• Manufacturer: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Engine Code: ADR
• Quantity per packing unit: 5
• Thickness [mm]: 11
• Inner Diameter [mm]: 85
• Outer Diameter [mm]: 105
• Fitting Position: transmission sided
• Weight [kg]: 0.103
• Manufacturer: VAICO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Engine Code: ADR
• Fitting Position: transmission sided
• Supplementary Article/Info 2: with flange
• Outer Diameter [mm]: 111
• Inner Diameter [mm]: 85
• Height [mm]: 16
• Manufacturer: DELLO AUTOMEGA

• Supplementary Article/Info 2: with flange
• Fitting Position: transmission sided
• Fabrication Number: NUP-VW-006
• Manufacturer: NTY

• Required quantity: 1
• Quantity per packing unit: 5
• Fitting Position: transmission sided
• Manufacturer: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Fitting Position: transmission sided
• Inner Diameter [mm]: 85
• Outer Diameter [mm]: 105
• Height [mm]: 11
• Manufacturer: DELLO AUTOMEGA

• Engine Code: APT
• Construction Year from: 02.1999
• Fitting Position: transmission sided
• for OE number: 038103171
• Material: PTFE (polytetrafluoroethylene)
• Manufacturer: FAI

• Fitting Position: transmission sided
• Housing Type: with housing
• Housing material: Cast Aluminium
• Alternative Repair Kit: 101 407
• Sealing lip material: PTFE (polytetrafluoroethylene)
• Manufacturer: TOPRAN HANS PRIES

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Fitting Position: transmission sided
• Engine Code: ADR
• Inner Diameter [mm]: 85
• Outer Diameter [mm]: 105
• Height [mm]: 11
• Radial Shaft Seal Design: ASW
• Swirl Type: Left-hand Twist
• Material: FPM (fluoride rubber)
• Dust Cover: with dust lip
• Supplementary Article/Info 2: with mounting sleeve
• Manufacturer: ELRING

• Fitting Position: transmission sided
• Weight [kg]: 0.17
• Inner Diameter [mm]: 85
• Required quantity: 1
• Supplementary Article/Info 2: with flange
• General Information: sealing flang; rear
• Manufacturer: VIKA

• Required quantity: 1
• Fitting Position: frontal sided
• Engine Code: APT, ARG
• Inner Diameter [mm]: 32
• Outer Diameter [mm]: 47
• Width [mm]: 10
• SVHC: No SVHC present!
• Manufacturer: INA

• Engine Code: ADR, APT, ARG
• Quantity per packing unit: 5
• Fitting Position: transmission sided
• Inner Diameter [mm]: 85
• Weight [kg]: 0.265
• Manufacturer: VAICO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Fitting Position: transmission sided
• Inner Diameter [mm]: 85
• Radial Shaft Seal Design: SP
• Housing Type: with housing
• Name: DRM 01416
• Manufacturer: DR.MOTOR AUTOMOTIVE

• Engine Code: ADR
• Fitting Position: transmission sided
• Supplementary Article/Info 2: with mounting sleeve
• Height 1 [mm]: 11
• Outer Diameter 1 [mm]: 105
• Inner Diameter 1 [mm]: 85
• Material: FPM (fluoride rubber)
• for OE number: 068103071F
• Swirl Type: Alternating Twist
• Manufacturer: CORTECO

• Outer Diameter [mm]: 47
• Thickness [mm]: 10
• Inner Diameter [mm]: 32
• Fitting Position: transmission sided
• Weight [kg]: 0.195
• Manufacturer: VAICO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Inner Diameter [mm]: 85
• Fitting Position: transmission sided
• Weight [kg]: 0.17
• Supplementary Article/Info 2: with flange
• Manufacturer: FEBI BILSTEIN
• Additional information: FE37745
• Lisainfo: FE37745

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Engine Code: ADR, APT, ARG
• Fitting Position: transmission sided
• Supplementary Article/Info 2: with mounting sleeve
• Height 1 [mm]: 15.7
• Outer Diameter 1 [mm]: 131
• Outer Diameter 2 [mm]: 152
• Inner Diameter 1 [mm]: 85
• Material: PTFE (polytetrafluoroethylene)
• for OE number: 028103171B
• Swirl Type: Alternating Twist
• Manufacturer: CORTECO
• Name: CO 20033462

• Fitting Position: transmission sided
• Weight [kg]: 0.17
• Inner Diameter [mm]: 85
• Required quantity: 1
• Supplementary Article/Info 2: with flange
• General Information: sealing flang; rear
• Manufacturer: VIKA

• Fitting Position: transmission sided
• Engine Code: ADR, APT, ARG
• Block Separation:
• Supplementary Article/Info 2: with flange
• Manufacturer: REINZ
• Name: RN 81-90000-00

• Fitting Position: transmission sided
• Inner Diameter [mm]: 85
• Radial Shaft Seal Design: SP
• Swirl Type: Left-hand Twist
• Housing Type: with housing
• Supplementary Article/Info 2: with mounting sleeve
• Manufacturer: ELRING
• Lisainfo: 804.850 ELR
• Additional information: 804.850 ELR

Material: PTFE (polytetrafluoroethylene)/ACM (polyacrylate rubber) Installation Information: Mounting dry and without any additional oil and grease