• Oxygen Sensor: Diagnostic Probe, Heated
• Fitting Position: Left, Right, after catalytic converter
• Block Separation:
• Number of circuits: 4
• Connector/Clamp: Connector may need adjustment
• Name: LAMBDA ANDUR
• Manufacturer: MAX
• Lisainfo: MGS-615
• Additional information: MGS-615

• Fitting Position: Right, after catalytic converter
• Cable Length [mm]: 909
• Oxygen Sensor: Planar Sensor, Heated
• Manufacturer: DELPHI
• Name: DE ES20178-12B1

• Oxygen Sensor: Diagnostic Probe
• Fitting Position: Left Front, Right Front
• Quantity: 2
• Length [mm]: 1,020
• Number of connectors: 4
• Manufacturer: VERNET

• Construction Year from: 11.2002
• Transmission Type: Automatic Transmission
• Fitting Position: Right, after catalytic converter
• Line insulation design: with silicone-coated woven-fibre insulation
• Number of pins: 4
• Socket colour: black
• Number of circuits: 4
• Connector Shape: D Shape
• Cable Length [mm]: 625
• Thread Size: M18 x 1,5
• for OE number: 021 906 262 C
• Length [mm]: 800
• Oxygen Sensor: Diagnostic Probe, Thread pre-greased
• Version: ZR-PLANAR
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Oxygen Sensor: Diagnostic Probe, Unheated
• Fitting Position: Right
• Number of pins: 4
• Cable Length [mm]: 1,050
• Quality: OE EQUIVALENT
• for OE number: 058906265B
• Manufacturer: MEAT&DORIA

• Conductor Number: 4
• Resistor [Ohm]: 9
• Number of circuits: 4
• Length [mm]: 1,731
• Cable Length [mm]: 1,731
• Oxygen Sensor: Heated
• Name: LAMBDA ANDUR
• Manufacturer: MAG

• Oxygen Sensor: Diagnostic Probe
• Fitting Position: after catalytic converter, Left, Right
• Block Separation:
• Number of circuits: 4
• Recommended change interval [km]: 160,000
• Connector/Clamp: Connector may need adjustment
• Name: LAMBDA ANDUR
• Manufacturer: BOS

• Construction Year from: 03.2003
• Fitting Position: Right, after catalytic converter
• Corresponds to the original part in colour: black
• Line insulation design: with silicone-coated woven-fibre insulation
• Oxygen Sensor: Planar Sensor, Heated, Thread pre-greased
• Supplementary Article/Info 2: without plug
• Cable Length [mm]: 210
• Number of circuits: 4
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Fitting Position: Left
• Thread Size: M18x1.5
• Cable Length [mm]: 750
• Number of pins: 4
• Manufacturer Restriction: DENSO
• Quality: OE
• Weight [g]: 93
• Gross Weight [g]: 140
• Manufacturer: DENSO
• Name: Lambda sensor
• Quality class: Q

Oxygen Sensor: Diagnostic Probe, Heated, Planar Sensor, Thread pre-greased, Switching-type Oxygen Sensor Additional information: "Tootja: DENSO
(kvaliteediklass: Q)" Lisainfo: "Tootja: DENSO
(kvaliteediklass: Q)"

• Engine Code: BFL
• Construction Year from: 11.2002
• Oxygen Sensor: Regulating Sensor, Heated
• Fitting Position: before catalytic converter
• Number of circuits: 5
• Length [mm]: 1,500
• Name: LAMBDA ANDUR
• Manufacturer: MAX

• Oxygen Sensor: Diagnostic Probe, Thread pre-greased
• Fitting Position: Left, after catalytic converter
• Line insulation design: with silicone-coated woven-fibre insulation
• Overall Length [mm]: 1,800
• Number of pins: 4
• Recommended change interval [km]: 160,000
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Construction Year from: 11.2002
• Number of pins: 5
• Overall Length [mm]: 1,510
• Oxygen Sensor: Regulating Sensor
• Lisainfo: Lambda Sensor
• Additional information: Lambda Sensor

• Oxygen Sensor: Diagnostic Probe, Heated
• External Thread Size: M18 x 1,5
• Spanner Size: 22
• Number of circuits: 4
• Cable Length [mm]: 1,760
• Weight [kg]: 0.155
• Manufacturer: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Oxygen Sensor: Regulating Sensor
• Fitting Position: Left, before catalytic converter
• Length [mm]: 1,500
• Number of pins: 6
• Manufacturer: FAE

• Fitting Position: Left
• for OE number: 077906265AD, 022906262AH
• Thread Size: M18x1.5
• Cable Length [mm]: 950
• Number of pins: 4
• Manufacturer Restriction: DENSO
• Quality: OE
• Weight [g]: 127
• Gross Weight [g]: 160
• Manufacturer: DENSO
• Name: Lambda sensor
• Quality class: Q

Oxygen Sensor: Diagnostic Probe, Heated, Planar Sensor, Thread pre-greased, Switching-type Oxygen Sensor Additional information: "Tootja: DENSO
PASSAT (3B3), 11.00-
(kvaliteediklass: Q)" Lisainfo: "Tootja: DENSO
PASSAT (3B3), 11.00-
(kvaliteediklass: Q)"

• Construction Year from: 11.2002
• Transmission Type: Automatic Transmission
• Fitting Position: Right, after catalytic converter
• Line insulation design: with silicone-coated woven-fibre insulation
• Length [mm]: 730
• Connector Shape: D Shape
• Conductor Number: 4
• Cable Length [mm]: 600
• Thread Size: M18 x 1,5
• Housing Colour: black
• Oxygen Sensor: Diagnostic Probe, Thread pre-greased
• Version: ZR-PLANAR
• Manufacturer: VEMO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Oxygen Sensor: Regulating Sensor
• Length [mm]: 1,700
• Number of pins: 4
• Supplementary Article/Info 2: with mounting manual
• Manufacturer: FAE

• Fitting Position: Right Front, before catalytic converter
• Rated Voltage [V]: 12
• Number of pins: 6
• Connector Shape: oval
• Cable Length [mm]: 1,510
• Overall Length [mm]: 1,538
• Spanner Size: 22
• Thread Size: M 18
• Thread Pitch [mm]: 1.5
• Supplementary Article/Supplementary Info: with cable tie
• Supplementary Article/Info 2: with plastic socket, with heat shield pipe
• Lubrication: with grease lubrication
• Full Set:
• Manufacturer: TOPRAN

Oxygen Sensor: Regulating Sensor, Broadband Oxygen Sensor, Heated, Planar Sensor General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Construction Year from: 11.2002
• Transmission Type: Automatic Transmission
• Fitting Position: Right, after catalytic converter
• Oxygen Sensor: Diagnostic Probe
• Pikkus (mm): 950
• Ülekandeliinide arv: 4
• Manufacturer: VDO

• Fitting Position: Left Front, after catalytic converter
• Oxygen Sensor: Diagnostic Probe, Regulating Sensor
• Cable Length [mm]: 1,750
• Number of pins: 4
• Assy./disassy. by qualified personnel required!:
• Manufacturer: HELLA
• Name: HE 6PA358066391

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Lambda andur: soojendatud
• Pistikkontaktide arv: 4
• Manufacturer: AIC

Üldine informatsioon: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Number of circuits: 5
• Length [mm]: 1,510
• Conductor Number: 5
• Cable Length [mm]: 1,510
• Oxygen Sensor: Heated
• Name: LAMBDA ANDUR
• Manufacturer: MAG

• Number of pins: 4
• Cable Length [mm]: 1,800
• Thread Size: M18x1,5
• Switch Pressure [bar]: 4
• Connector Shape: oval
• Manufacturer: VALEO

Oxygen Sensor: Diagnostic Probe, Planar Sensor, Thread pre-greased, Heated Fitting Position: before catalytic converter, after catalytic converter

• Lambda andur: soojendatud
• Soovituslik vahetusintervall (km): 160 000
• Ühendus/klemm: vajadusel kohandada pistikühendus
• Pistikkontaktide arv: 4
• pikkus üle kõige (mm): 750
• Üldine informatsioon: lambda probe
• Manufacturer: BORSEHUNG

• Lambda andur: Bistabiilne andur
• Pinge [V]: 12
• Värv: punane
• Garantii: 3 aastat garantii
• Ülekandeliinide arv: 5
• Kaal (kg): 0,15
• Rakendustüüp: elektriline
• Oluline on võrrelda vana uue osaga (eriti OE-numbrit):
• Manufacturer: SKV GERMANY
• Name: CE 09SKV905

• Required quantity: 2
• Number of pins: 5
• Connector Shape: D Shape
• Cable Length [mm]: 1,360
• Fitting Position: Exhaust Manifold
• Oxygen Sensor: Broadband Oxygen Sensor
• Quality: OE EQUIVALENT
• for OE number: 022906262H
• Manufacturer: MEAT&DORIA

• Fitting Position: before catalytic converter
• Cable Length [mm]: 950
• Name: LAMBDA ANDUR
• Manufacturer: DLP

Oxygen Sensor: Regulating Sensor, Switching-type Oxygen Sensor, Heated

• Engine Code: BFL
• Vehicle Identification Number (VIN) from: 4E-3-000 001
• Fitting Position: Left, Right
• Oxygen Sensor: Diagnostic Probe, Heated
• Voltage [V]: 12
• Conductor Number: 4
• Cable Length [mm]: 950
• Manufacturer: PIERBURG

• Oxygen Sensor: Regulating Sensor
• Fitting Position: before catalytic converter, Left
• Number of circuits: 5
• Overall Length [mm]: 1,510
• Recommended change interval [km]: 250,000
• Name: LAMBDA ANDUR
• Manufacturer: BOS

• Lambda andur: Bistabiilne andur
• Garantii: 3 aastat garantii
• Kaal (kg): 0,15
• Oluline on võrrelda vana uue osaga (eriti OE-numbrit):
• Tehniline informatsioon: Universal
• Name: CE 09SKV915
• Manufacturer: ESEN SKV

• Oxygen Sensor: Regulating Sensor
• Exhaust System: before catalytic converter
• Lambda andur: Bistabiilne andur
• Pinge [V]: 12
• Garantii: 3 aastat garantii
• Kaal (kg): 0,16
• Rakendustüüp: elektriline
• Oluline on võrrelda vana uue osaga (eriti OE-numbrit):
• Manufacturer: SKV GERMANY
• Name: CE 09SKV907

• Fitting Position: before catalytic converter
• Oxygen Sensor: Regulating Sensor
• Cable Length [mm]: 1,500
• Number of pins: 6
• Exhaust System: before catalytic converter
• Assy./disassy. by qualified personnel required!:
• SVHC: 7439-92-1; Lead
• Manufacturer: HEL

Brief Information: *** HELLA Electronics OE competence for over 60 years. Name: SONDA LAMBDA VV GOLF IV, TRANSPORTER, PHAETON 1,4-6,0 97-

• Lambda andur: soojendatud
• Ühendushulk: 5
• Üldine informatsioon: lambda probe; 5 wire
• Manufacturer: VIKA

• Fitting Position: Front
• Line insulation design: with silicone-coated woven-fibre insulation
• Conductor Number: 5
• Thread Size: M18 x 1,5
• Connector Shape: D Shape
• Cable Length [mm]: 1,510
• Supplementary Article/Supplementary Info: with cable tie
• Oxygen Sensor: Broadband Oxygen Sensor, Thread pre-greased
• Number of circuits: 5
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.