• Colour Coding: grey
• Number of pins: 2
• Lisainfo: Sender for water temperature gauge, 2 pins
• Additional information: Sender for water temperature gauge, 2 pins

• Fitting Position: Front
• Vehicle Equipment: for vehicles with air conditioning
• Colour: black
• Number of pins: 2
• Manufacturer: JP GROUP A/S
• Lisainfo: Sensor, exterior temperature
• Additional information: Sensor, exterior temperature

• Number of connectors: 2
• Material: Plastic
• Lisainfo: Water level switch, washer
• Additional information: Water level switch, washer

• for PR number: 9Q2, 9Q4
• Weight [kg]: 0.013
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• for OE number: 95510612500
• Manufacturer: KAMOKA

• Fitting Position: Front
• Colour: black
• Vehicle Equipment: for vehicles with air conditioning
• Number of pins: 2
• Supplementary Article/Info 2: without cable
• Connector Shape: D Shape
• Fabrication Number: ECT-AU-001
• Manufacturer: NTY
• Name: NTY ECT-AU-001

• for PR number: 9Q2, 9Q4
• Number of pins: 2
• Connector Shape: D Shape
• Consult accessories list for recommended additional repairs:
• Name: NIVOOLšLITI, PESUVEEKOGUS
• Manufacturer: HAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Supplementary Article/Info 2: with plug
• Conductor Number: 2
• Name: Kaabli paranduskomplekt, v„listemperatuuri andur
• Manufacturer: ABA

General Information: The following information is for general and informational purposes only and does not constitute warranty terms. Warranty terms and conditions are available from our dealers and in our general terms and conditions of sale. Abakus spare/repair parts are intended only for vehicle repairs in order to restore their original functionality. Abakus spare/repair parts are used or sold to users only for the purpose of repairing vehicles to restore their original look and functionality and are not original/genuine/OE/OEM/OES replacement parts. These items do not originate from the vehicle manufacturer and may be the subject of a design not owned by Abakus and the manufacturer of this spare part. They may only be used for repairs to restore the intended vehicle to its original appearance. Our products are delivered without instruction of installation. Installation of our product may only be carried out by trained specialist technicians in specific car repairs. Products supplied by us are exclusively intended for proper and appropriate use. The warranty may become invalid in the event of: improper installation or repair, unsuitable application or use, installation or repair made outside specialist car workshops. Warranty claims are lost if the vehicle is modified and used for motor sports, tuning or similar events (except our tuning parts which are described in TecDoc and on our price list). Warranty application should include complete documentation among others: chassis no., first registration, vehicle mileage, information about LPG installation, fault memory log, pictures, our QC (quality check) code, installation invoice, contact details of the car repair workshop performing the replacement or repair. Warranty application are available in our Client Panel system. Complaints may require supplementing data such as error memory logs. Incomplete documentation may result in rejection of the claim. Any damage caused during transport is not considered quality damage and will be considered on an individual basis. The product is intended for use within the performance limits specified by the manufacturer and should only be used by qualified personnel who have been trained to operate this product. Before each use, the product should be checked for damage or fixing of its parts and not used if any defects or loose parts are found. Failure to follow the manufacturer's guidelines could result in potential product damage or even injury. Wear appropriate protective clothing if necessary when working with the product.

• Construction Year to: 03.2008
• Colour: black
• Number of pins: 2
• Name: ANDUR,VŽLISTEMPERATUUR
• Manufacturer: MAX
• Lisainfo: 21-0339
• Additional information: 21-0339

• Vehicle Equipment: for vehicles with on-board computer
• for PR number: 9Q2, 9Q4
• Block Separation:
• Number of connectors: 2
• Material: Plastic
• Weight [kg]: 0.01
• Name: ANDUR,PESUVEETASE
• Manufacturer: FEB

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Vehicle Equipment: for vehicles with air conditioning
• Number of pins: 2
• Manufacturer: ABAKUS LORO

General Information: The following information is for general and informational purposes only and does not constitute warranty terms. Warranty terms and conditions are available from our dealers and in our general terms and conditions of sale. Abakus spare/repair parts are intended only for vehicle repairs in order to restore their original functionality. Abakus spare/repair parts are used or sold to users only for the purpose of repairing vehicles to restore their original look and functionality and are not original/genuine/OE/OEM/OES replacement parts. These items do not originate from the vehicle manufacturer and may be the subject of a design not owned by Abakus and the manufacturer of this spare part. They may only be used for repairs to restore the intended vehicle to its original appearance. Our products are delivered without instruction of installation. Installation of our product may only be carried out by trained specialist technicians in specific car repairs. Products supplied by us are exclusively intended for proper and appropriate use. The warranty may become invalid in the event of: improper installation or repair, unsuitable application or use, installation or repair made outside specialist car workshops. Warranty claims are lost if the vehicle is modified and used for motor sports, tuning or similar events (except our tuning parts which are described in TecDoc and on our price list). Warranty application should include complete documentation among others: chassis no., first registration, vehicle mileage, information about LPG installation, fault memory log, pictures, our QC (quality check) code, installation invoice, contact details of the car repair workshop performing the replacement or repair. Warranty application are available in our Client Panel system. Complaints may require supplementing data such as error memory logs. Incomplete documentation may result in rejection of the claim. Any damage caused during transport is not considered quality damage and will be considered on an individual basis. The product is intended for use within the performance limits specified by the manufacturer and should only be used by qualified personnel who have been trained to operate this product. Before each use, the product should be checked for damage or fixing of its parts and not used if any defects or loose parts are found. Failure to follow the manufacturer's guidelines could result in potential product damage or even injury. Wear appropriate protective clothing if necessary when working with the product.

• Colour Coding: grey
• Fabrication Number: ECT-VW-000
• Manufacturer: NTY
• Name: NTY ECT-VW-000

• General Information: temperature sensor
• Manufacturer: VIKA

• Quantity: 1
• Weight [kg]: 0.015
• Number of connectors: 2
• Screw length below head [mm]: 20
• Colour: grey
• Colour Coding: grey
• General Information: temperature sensor; grey; 2 pins
• Manufacturer: VIKA

• Quantity: 1
• Weight [kg]: 0.015
• Number of connectors: 2
• Screw length below head [mm]: 20
• Colour: black
• Colour Coding: grey
• General Information: temperature sensor; black
• Manufacturer: VIKA

• Connector Shape: oval, D Shape
• Colour Coding: grey
• Sensor Type: NTC Sensor
• Number of pins: 2
• Consult accessories list for recommended additional repairs:
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Fabrication Number: ECT-AU-004
• Number of pins: 4
• Colour Coding: green
• Connector Shape: oval
• Manufacturer: NTY

• Engine Code: BKN
• Number of connectors: 4
• Manufacturer: 3RG

• Fabrication Number: ECT-AU-005
• Number of pins: 2
• Supplementary Article/Info 2: with seal ring
• Sensor Type: NTC Sensor
• Socket colour: black
• Manufacturer: NTY

• General Information: distance sensor
• Manufacturer: VIKA

• Number of connectors: 2
• Manufacturer: 3RG

• for OE number: 1120193
• Cable Length [mm]: 310
• Sensor Type: Passive sensor
• Manufacturer: KAMOKA

• Colour Coding: grey
• Number of pins: 2
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: MAX

• Connector Shape: D Shape
• Material: Plastic
• Number of pins: 4
• Plug Type: Female
• Sensor Type: NTC Sensor
• Name: NI 207009
• Manufacturer: NISSENS

Technical Information: FIRST FIT - a time-saving installation! Find all additional parts such as O-rings, clip, washer in the box.

• Housing Colour: black
• Number of pins: 4
• Spanner Size: 0
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: DLP

• Fitted Diameter [mm]: 20
• Number of pins: 4
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: MAX

• Sensor Type: NTC Sensor
• Mounting Type: Clamped
• Connector Shape: D Shape
• Number of pins: 2
• for OE number: 06A919501
• Supplementary Article/Info 2: with mounting parts
• Name: Andur,Jahutusvedeliku temp.
• Manufacturer: NRF

• Number of pins: 2
• Guarantee: 3 years guarantee
• Weight [kg]: 0.01
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 17SKV703

• Sensor Type: NTC Sensor
• Mounting Type: Clamped
• Connector Shape: D Shape
• Number of pins: 4
• for OE number: 059919501A
• Supplementary Article/Info 2: with mounting parts
• Name: Andur,Jahutusvedeliku temp.
• Manufacturer: NRF

• Weight [g]: 15
• Name: IM 5309
• Manufacturer: ORIGINAL IMPERIUM

• Number of pins: 2
• Colour: black
• Material: Plastic
• Manufacturer: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Number of connectors: 4
• Connector Shape: round
• Thread Size: 20 mm
• Number of pins: 4
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: VER

• Thread Size: 20 mm
• Number of pins: 2
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: VER
• Additional information: WS2607
• Lisainfo: WS2607

• Engine Code: BKN
• Housing Colour: green
• Corresponds to the original part in colour: black
• Manufacturer: FACET

• Engine Code: BKN
• Colour: grey
• for article number: 26.0015K, 7.3278K, 7.7946
• Manufacturer: FACET

• Engine Code: BKN
• Housing Colour: green
• Corresponds to the original part in colour: black
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: EPS

• Engine Code: BKN
• Colour: grey
• for article number: 1.660.015K, 1.830.278K, 1.879.946
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: EPS
• Additional information: 1-830-278
• Lisainfo: 1-830-278

• Number of connectors: 2
• Colour: black
• Weight [kg]: 0.003
• Manufacturer: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Thread Size: M20
• Number of pins: 2
• Housing Colour: grey
• Connector Shape: oval
• Manufacturer: ERA

• for OE number: 078 919 501 C
• Manufacturer: TRUCKTEC

• Quantity: 1
• General Information: ambient air temperature sensor
• Manufacturer: BORSEHUNG

• Sensor Type: NTC Sensor
• Supplementary Article/Info 2: with seal ring
• Colour: black
• Number of pins: 2
• Name: ANDUR,JAHUTUSVEDELIKU TEMP.
• Manufacturer: MEY

• Housing Colour: grey
• Number of pins: 2
• Spanner Size: 0
• Manufacturer: DELPHI
• Name: DE TS10278

• Housing Colour: black
• Number of pins: 2
• Name: ANDUR,VŽLISTEMPERATUUR
• Manufacturer: DLP
• Lisainfo: TS10266
• Additional information: TS10266

• Version: 2
• Connector Shape: D Shape
• Material: Plastic
• Number of pins: 2
• Plug Type: Female
• Sensor Type: NTC Sensor
• Manufacturer: NISSENS

Technical Information: FIRST FIT - a time-saving installation! Find all additional parts such as O-rings, clip, washer in the box.

• Guarantee: 3 years guarantee
• Weight [kg]: 0.01
• Number of pins: 2
• Always compare old and new part (in particular OE No.):
• Name: CE 17SKV698
• Manufacturer: ESEN SKV

• Mounting Type: Plugged
• Voltage [V]: 12
• Supplementary Article/Supplementary Info: with gasket/seal
• Colour: black
• Sensor Type: NTC Sensor
• Number of pins: 2
• Supplementary Article/Info 2: with retaining ring
• Corresponds to the original part in colour: black, grey
• Fitting Depth [mm]: 20
• Assy./disassy. by qualified personnel required!:
• SVHC: 7439-92-1; Lead
• Name: Andur,Jahutusvedeliku temp.
• Manufacturer: HEL

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Number of pins: 2
• Colour Coding: grey
• Supplementary Article/Info 2: with seal ring
• Manufacturer: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Number of pins: 2
• Weight [kg]: 0.3
• Packaging length [cm]: 12
• Packaging width [cm]: 8
• Packaging height [cm]: 6

• Vehicle Equipment: for vehicles with automatic climate control
• Number of pins: 2
• Fitting Position: Air duct, to interior blower
• Housing Colour: grey
• Name: TEMPERATUURILšLITUS,KLIIMAVENTILAATOR
• Manufacturer: HAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Number of connectors: 4
• Connector Shape: round
• Weight [kg]: 0.017, 0.027
• Supplementary Article/Supplementary Info: with gasket/seal
• for OE number: 059 919 501 A
• Colour Coding: green
• Spring Design: Retaining Spring
• Number of pins: 4
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Mounting Type: Plugged
• Voltage [V]: 12
• Supplementary Article/Supplementary Info: with gasket/seal
• Colour: green
• Sensor Type: NTC Sensor
• Number of pins: 4
• Supplementary Article/Info 2: with retaining ring
• Corresponds to the original part in colour: green, black
• Assy./disassy. by qualified personnel required!:
• Name: Andur,Jahutusvedeliku temp.
• Manufacturer: HEL

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Number of connectors: 2
• Colour Coding: grey
• Screw length below head [mm]: 20
• Weight [kg]: 0.03
• Supplementary Article/Supplementary Info: with gasket/seal, with retaining spring
• Name: SW 30 92 9318
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Connector Shape: D Shape
• Number of pins: 3
• Supplementary Article/Info 2: with cable
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Number of pins: 2
• Manufacturer: FAE

• Quantity: 1
• Screw length below head [mm]: 20
• Weight [kg]: 0.015
• Number of connectors: 2
• Colour Coding: grey
• General Information: coolant temperature sensor
• Manufacturer: BORSEHUNG

• for PR number: A8U
• Number of pins: 2
• Colour: black
• Manufacturer: METZGER

• Number of pins: 2
• Supplementary Article/Info 2: with seal ring
• Connector Shape: rectangular, angled
• Housing material: GRP (Glass fibre Reinforced Plastic)
• Component Number: G 191, G 192
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Connector Shape: D Shape
• Supplementary Article/Info 2: without cable
• Colour: black
• Number of pins: 2
• Fitting Position: Front
• Vehicle Equipment: for vehicles with air conditioning
• Power [W]: 0.06
• Manufacturer: METZGER

• Number of pins: 2
• Connector Shape: rectangular
• Supplementary Article/Info 2: without cable
• Vehicle Equipment: for vehicles with automatic climate control
• for OE number: 1K0907543G
• Manufacturer: MEAT&DORIA

• for OE number: 1K0 907 453A
• Vehicle Equipment: for vehicles with automatic climate control
• Fitting Position: to interior blower, Lower, Centre
• Version: IAM
• Manufacturer: METZGER

• Length [mm]: 36
• Width [mm]: 17
• Height [mm]: 13
• Weight [kg]: 0.035
• Vehicle Equipment: for vehicles with air conditioning
• Number of pins: 2
• Manufacturer: VEMO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Number of pins: 2
• Housing Colour: grey
• Manufacturer: FAE

• Construction Year to: 05.2006
• Sensor Type: Inductive Sensor
• Number of pins: 3
• Supplementary Article/Info 2: with cable
• Name: ANDUR, VŽNTVOLL
• Manufacturer: MAX

• Diameter [mm]: 26
• Number of pins: 2
• Supplementary Article/Info 2: with seal ring
• Spring Design: Retaining Spring
• Length [mm]: 20
• Housing Colour: blue
• Height [mm]: 57
• Weight [kg]: 0.02
• Colour: grey
• Number of connectors: 2
• Manufacturer: VEMO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Quantity: 1
• General Information: interior temperature sensor
• Manufacturer: BORSEHUNG

• Required quantity: 1
• Number of pins: 3
• Sensor Type: Inductive Sensor
• Supplementary Article/Info 2: with cable
• Housing Colour: black
• Socket colour: grey
• Manufacturer: BREMI

• Construction Year to: 05.2006
• Voltage [V]: 12
• Length [mm]: 350
• Number of pins: 3
• Guarantee: 3 years guarantee
• Weight [kg]: 0.11
• Operating Mode: Electric
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 17SKV227

• Cable Length [mm]: 321
• Number of pins: 3
• Manufacturer: DELPHI
• Name: DE SS10891

• Number of pins: 2
• Weight [kg]: 0.073
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Number of pins: 2
• Vehicle Equipment: for vehicles with automatic climate control
• Fitting Position: Left
• Manufacturer: METZGER

• for OE number: 06E 907 660, 948 606 150 00
• Height [mm]: 106
• Number of pins: 3
• Fitting Depth [mm]: 90
• Connector Shape: D Shape
• Number of mounting bores: 3
• Fabrication Number: EPO-AU-002
• Manufacturer: NTY
• Name: NTY EPO-AU-002

• Number of pins: 2
• Vehicle Equipment: for vehicles with air conditioning
• Manufacturer: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Number of pins: 2
• Manufacturer: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.