• Fitting Position: Rear Axle
• Brake System: Teves
• Height [mm]: 58.3
• Width [mm]: 62
• Thickness [mm]: 15
• Wear Warning Contact: prepared for wear warning indicator
• Manufacturer: JP GROUP
• Lisainfo: Brake pad set, rear, 15.0 mm
• Additional information: Brake pad set, rear, 15.0 mm

• Fitting Position: Rear Axle
• Inner brake drum diameter [mm]: 164
• Width [mm]: 20
• Supplementary Article/Supplementary Info: without lever
• Lisainfo: Brake shoe set, 164x20 mm
• Additional information: Brake shoe set, 164x20 mm

• Fitting Position: Rear Axle
• Width [mm]: 62
• Thickness [mm]: 15
• Height [mm]: 59
• Wear Warning Contact: excl. wear warning contact
• Supplementary Article/Supplementary Info: with accessories
• Brake System: ATE
• Manufacturer: KAMOKA UK£ADY HAMULCOWE

• Filter type: In-Line Filter
• Thread Size 1: M12X1.5
• Thread Size 2: M14X1.5
• Height [mm]: 170
• Outer Diameter 1 [mm]: 82
• Outer Diameter 2 [mm]: 91
• Manufacturer: DENCKERMANN FILTRY

• Fitting Position: Rear Axle
• Diameter [mm]: 164
• Width [mm]: 20
• Brake System: TEVES
• Manufacturer: DENCKERMANN HAMULCE

• Fitting Position: Rear Axle
• Width [mm]: 61.8
• Thickness [mm]: 15
• Height [mm]: 58.6
• Brake System: ATE
• Manufacturer: DENCKERMANN ZAWIESZENIE

Wear Warning Contact: prepared for wear warning indicator, excl. wear warning contact

• Height [mm]: 168
• Outer Diameter [mm]: 81
• Filter type: In-Line Filter
• Outer Diameter 1 [mm]: 89
• Thread Size Entry: M 12 X 1.5
• Thread Size Exit: M 14 X 1.5
• Manufacturer: DRIVE

• Diameter [mm]: 90
• Height [mm]: 185
• Filter type: Spin-on Filter
• Weight [kg]: 0.473
• Manufacturer: VAICO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Connecting thread: M14x1,5
• Diameter [mm]: 86
• Supplementary Article/Supplementary Info: with gaskets/seals
• Filter type: Spin-on Filter
• Thread Size: M12X1,5
• Height [mm]: 172.3
• Housing material: Metal
• Name: KšTUSEFILTER
• Manufacturer: MEY

• Fitting Position: Rear Axle
• Braking/Drive Dynamics: for vehicles with ABS
• Width 1 [mm]: 61.7
• Height 1 [mm]: 58.4
• Thickness 1 [mm]: 15.2
• Brake System: ATE
• Wear Warning Contact: prepared for wear warning indicator
• Weight [kg]: 0.63
• Installation Information: Important: Observe Fitting Instructions
• Manufacturer: A.B.S.

• Fitting Position: Rear Axle
• Width [mm]: 20
• Brake System: Ate
• Inner brake drum diameter [mm]: 164
• Weight [kg]: 0.8
• Manufacturer: TOMEX BRAKES

• Article number of recommended accessories: 98021302, 98021310
• Height [mm]: 58.5
• Thickness [mm]: 15
• Wear Warning Contact: prepared for wear warning indicator
• Brake System: Teves
• Fitting Position: Rear Axle
• Width [mm]: 63
• Name: PIDURIKLOTSI KOMPLEKT,KETASPIDUR
• Manufacturer: MAX

• Filter type: In-Line Filter
• Outer Diameter 1 [mm]: 75
• Thread Size 1: M14 x 1,5
• Thread Size: M12 x 1,5
• Height [mm]: 147
• Manufacturer: KOLBENSCHMIDT

• Fitting Position: Rear Axle
• Quantity per packing unit: 4
• Width [mm]: 61.7
• Article number of recommended accessories: KS0136, KS0137
• Height [mm]: 58.5
• Thickness [mm]: 15.2
• Brake System: ATE
• Manufacturer: LPR

• Quantity per packing unit: 4
• Fitting Position: Rear Axle
• Thickness [mm]: 15.2
• Width [mm]: 61.7
• Height [mm]: 58.5
• Wear Warning Contact: prepared for wear warning indicator
• Brake System: ATE
• Weight [kg]: 0.57
• Manufacturer: TOMEX BRAKES

• Fitting Position: Rear Axle
• Quantity per packing unit: 4
• Number of pads: 4
• Thickness [mm]: 15
• Length [mm]: 61.5
• Height [mm]: 58.3
• Wear Warning Contact: prepared for wear warning indicator
• Brake Pad: Without Bevelled Edges
• Brake System: Teves
• WVA Number: 21197
• Name: SK VKBP90373
• Manufacturer: SKF

• Length [mm]: 61.7
• Width [mm]: 58.5
• Test Mark: ECE R90 Approved
• Fitting Position: Rear Axle
• Thickness 1 [mm]: 15.2
• Wear Warning Contact: prepared for wear warning indicator
• Weight [kg]: 0.64
• Observe service information:
• Manufacturer: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Fitting Position: Rear Axle
• Brake System: Ate
• Quantity per packing unit: 4
• Test Mark: ECE-R90
• Height 1 [mm]: 58.5
• Wear Warning Contact: prepared for wear warning indicator
• Vibration: with vibration damper
• Width 1 [mm]: 61.7
• Thickness 1 [mm]: 15
• Manufacturer: METELLI UKL.HAMULCOWY

• Fitting Position: Rear Axle
• Quantity per packing unit: 4
• FMSI Code: D495-7374
• Test Mark: E4 90R-01601/1650
• Brake System: Continental
• Supplementary Article/Info 2: with anti-squeak plate
• Supplementary Article/Supplementary Info: without accessories
• WVA Number: 21197
• Friction Lining Material: Semi-Metallic
• Wear Warning Contact: prepared for wear warning indicator
• Width 1 [mm]: 61.8
• Width 2 [mm]: 61.6
• Height 1 [mm]: 58.3
• Height 2 [mm]: 58.3
• Thickness 1 [mm]: 15
• Thickness 2 [mm]: 15
• Manufacturer: DELPHI
• Name: DE LP946
• Additional information: LP946 DELPHI
• Lisainfo: LP946 DELPHI

• Fitting Position: Rear Axle
• Brake System: TEVES
• Width [mm]: 62
• Height [mm]: 58.3
• Thickness [mm]: 15.2
• WVA Number: 21197
• Wear Warning Contact: excl. wear warning contact
• Supplementary Article/Info 2: without anti-squeak plate
• Test Mark: ECE-R90
• Manufacturer: VALEO

• Fitting Position: Rear Axle
• Width [mm]: 61.7
• Height [mm]: 58.2
• Thickness [mm]: 15
• Wear Warning Contact: prepared for wear warning indicator
• Brake System: ATE
• Supplementary Article/Info 2: with anti-squeak plate
• Brake Caliper Type: Brake Caliper with 2 holding pins
• Name: PIDURIKLOTSI KOMPLEKT,KETASPIDUR
• Manufacturer: MEY

• Filter type: In-Line Filter
• Outer Diameter 1 [mm]: 82
• Thread Size 1: M14 x 1,5
• Thread Size: M12 x 1,5
• Height [mm]: 167
• Manufacturer: KOLBENSCHMIDT

• Length [mm]: 61.7
• Width [mm]: 58.5
• Test Mark: ECE R90 Approved
• Fitting Position: Rear Axle
• Thickness 1 [mm]: 15.2
• Wear Warning Contact: prepared for wear warning indicator
• Weight [kg]: 0.64
• Name: SW 10 91 6153
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Length [mm]: 62.2
• Width [mm]: 72.9
• Test Mark: ECE R90 Approved
• Fitting Position: Rear Axle
• Thickness 1 [mm]: 15.3
• Weight [kg]: 0.737
• Observe service information:
• Manufacturer: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• for OE number: 001 420 9520
• Fitting Position: Rear Axle
• Manufacturer: TRUCKTEC

• Vehicle Identification Number (VIN) from: F 242722
• WVA Number: 21153
• Fitting Position: Front Axle
• Manufacturer: JAPKO

• Thickness [mm]: 15.5
• Length [mm]: 62
• Weight [kg]: 0.65
• Height 1 [mm]: 59
• WVA Number: 21197
• Fitting Position: Rear Axle
• Manufacturer: JAPKO

• Thickness [mm]: 15.5
• Length [mm]: 62
• Weight [kg]: 0.65
• Height 1 [mm]: 59
• WVA Number: 21197
• Fitting Position: Rear Axle
• Manufacturer: ASHIKA-KLOCKI

• Filter type: Spin-on Filter
• Height [mm]: 167
• Outer Diameter [mm]: 82
• Thread Size Entry: M14x1.5
• Thread Size Exit: M12x1.5
• SVHC: No SVHC present!
• Manufacturer: FILTRON

• Fitting Position: Rear Axle
• Article number of recommended accessories: 98021302, 98021310
• Width [mm]: 63
• Height [mm]: 58.5
• Thickness [mm]: 15
• Wear Warning Contact: prepared for wear warning indicator
• Brake System: Teves
• Name: PIDURIKLOTSI KOMPLEKT,KETASPIDUR
• Manufacturer: QUARO

• Thickness [mm]: 19.4
• Length [mm]: 108
• Height 1 [mm]: 60
• WVA Number: 20941
• Fitting Position: Front Axle
• Brake System: TRW
• Manufacturer: JAPKO

• Manufacturer Restriction: ATE
• Wear Warning Contact: prepared for wear warning indicator
• Height [mm]: 73.5
• Thickness [mm]: 17.5
• Fitting Position: Front Axle
• Width [mm]: 100
• Name: PIDURIKLOTSI KOMPLEKT,KETASPIDUR
• Manufacturer: MAX

• Length [mm]: 62
• Width [mm]: 73
• Test Mark: ECE R90 Approved
• Fitting Position: Rear Axle
• Thickness 1 [mm]: 15
• Weight [kg]: 0.737
• Observe service information:
• Manufacturer: BLUE PRINT

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Fitting Position: Rear Axle
• Quantity per packing unit: 4
• Manufacturer Restriction: ATE
• Wear Warning Contact: prepared for wear warning indicator
• Test Mark: E1 90R 01025/185
• Height [mm]: 58.5
• Width [mm]: 61.7
• Thickness [mm]: 15.2
• Brake Caliper Type: Brake Caliper with 2 holding pins
• Name: PIDURIKLOTSI KOMPLEKT,KETASPIDUR
• Manufacturer: TRW
• Additional information: GDB987
• Lisainfo: GDB987

SVHC: No information available, please contact the manufacturer!

• Length [mm]: 62.2
• Width [mm]: 72.9
• Test Mark: ECE R90 Approved
• Fitting Position: Rear Axle
• Thickness 1 [mm]: 15.3
• Weight [kg]: 0.737
• Name: SW 10 91 6147
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Fitting Position: Rear Axle
• Supplementary Article/Info 2: with anti-squeak plate, with mounting manual
• Observe technical data:
• Material: Low-Metallic
• Test Mark: ECE-R90
• WVA Number: 21197
• Thickness [mm]: 15.2
• Width [mm]: 61.8
• Height [mm]: 58.7
• Brake System: ATE
• Name: PIDURIKLOTSI KOMPLEKT,KETASPIDUR
• Manufacturer: BOS

Article number of recommended accessories: 1987474100, 1987474101, 1987474128, 1987474901, 1987474257, 1987474730, 1987474180

• Fitting Position: Front Axle
• Brake System: TRW
• Width [mm]: 110
• Height [mm]: 59.4
• Thickness [mm]: 18.4
• WVA Number: 21028
• Wear Warning Contact: excl. wear warning contact
• Supplementary Article/Info 2: without anti-squeak plate
• Test Mark: ECE-R90
• Weight [kg]: 1.7
• Manufacturer: VALEO

• Fitting Position: Rear Axle
• Brake System: TEVES
• Width [mm]: 62
• Height [mm]: 58.4
• Thickness [mm]: 15
• WVA Number: 21197
• Wear Warning Contact: excl. wear warning contact
• Supplementary Article/Info 2: with anti-squeak plate
• Test Mark: ECE-R90
• Manufacturer: VALEO KLOCKI

• Fitting Position: Rear Axle
• Quantity per packing unit: 4
• Width [mm]: 62
• Thickness [mm]: 15
• Height [mm]: 58
• Wear Warning Contact: prepared for wear warning indicator
• Supplementary Article/Supplementary Info: without accessories
• Brake System: Teves
• WVA Number: 21197
• Manufacturer: BREMBO
• Name: BR P 50 009

• Filter type: Spin-on Filter
• Height [mm]: 167
• Outer Diameter [mm]: 82
• Thread Size Entry: M12x1.25
• Thread Size Exit: M 14x1,5
• Name: VA 587205
• Manufacturer: VALEO

• Fitting Position: Front Axle
• Quantity per packing unit: 4
• FMSI Code: D423-7311
• Test Mark: E9 90R-02A0823/2904
• Brake System: TRW
• Supplementary Article/Info 2: with anti-squeak plate
• Supplementary Article/Supplementary Info: with accessories
• WVA Number: 21028
• Friction Lining Material: Semi-Metallic
• Width 1 [mm]: 110.1
• Width 2 [mm]: 109.9
• Height 1 [mm]: 59.6
• Height 2 [mm]: 59.6
• Thickness 1 [mm]: 18.5
• Thickness 2 [mm]: 18.5
• Manufacturer: DELPHI LOCKHEED HAMULCE
• Name: DE LP608

Wear Warning Contact: prepared for wear warning indicator, incl. wear warning contact

• Fitting Position: Front Axle
• Width [mm]: 99.8
• Height [mm]: 73.5
• Thickness [mm]: 17.5
• Wear Warning Contact: prepared for wear warning indicator
• Brake System: ATE
• Supplementary Article/Info 2: with anti-squeak plate
• Name: PIDURIKLOTSI KOMPLEKT,KETASPIDUR
• Manufacturer: MEY

• Fitting Position: Rear Axle
• Width [mm]: 61.8
• Height [mm]: 58.6
• Thickness [mm]: 15
• Brake System: ATE
• Test Mark: E9 90R-02A1382/1617
• MAPP code available:
• Article number of recommended accessories: 13.0460-0186.2, 13.0460-0215.2, 24.8190-0401.2
• Observe dimensions:
• Name: PIDURIKLOTSI KOMPLEKT,KETASPIDUR
• Manufacturer: ATE
• Quality class: Q

Wear Warning Contact: prepared for wear warning indicator, excl. wear warning contact

• Fitting Position: Rear Axle
• Article number of recommended accessories: 98021302, 98021310, 82019500
• Width [mm]: 61.8
• Height [mm]: 58.5
• Thickness [mm]: 15
• Wear Warning Contact: prepared for wear warning indicator
• WVA Number: 21197
• Brake System: Teves
• Packaging length [cm]: 9.5
• Packaging width [cm]: 8.2
• Packaging height [cm]: 7.3
• Weight [kg]: 0.6
• Name: PIDURIKLOTSI KOMPLEKT,KETASPIDUR
• Manufacturer: TEX

• Filter type: In-Line Filter
• Height [mm]: 167
• Outer Diameter [mm]: 90
• Thread Size 1: M14x1,5
• Thread Size 2: M12x1,5
• Manufacturer: PURFLUX

• Filter type: In-Line Filter
• Outer Diameter [mm]: 90.5
• Height [mm]: 167
• Manufacturer: HENGST FILTER

• Fitting Position: Front Axle
• Brake System: TEVES
• Width [mm]: 100
• Height [mm]: 73.4
• Thickness [mm]: 17.5
• WVA Number: 21153
• Wear Warning Contact: excl. wear warning contact
• Supplementary Article/Info 2: with anti-squeak plate
• Test Mark: ECE-R90
• Weight [kg]: 1.69
• Manufacturer: VALEO

• Filter type: In-Line Filter
• Height [mm]: 168
• Outer Diameter [mm]: 81
• Outer Diameter 1 [mm]: 89
• Thread Size Entry: M12x1.5
• Thread Size Exit: M14x1.5
• SVHC: 7439-92-1; Lead
• Name: KšTUSEFILTER
• Manufacturer: MAN

• Fitting Position: Rear Axle
• Quantity per packing unit: 4
• Brake System: ATE
• Width [mm]: 62
• Height [mm]: 58
• Thickness [mm]: 15
• Wear Warning Contact: prepared for wear warning indicator
• Supplementary Article/Supplementary Info: Photo corresponds to scope of supply
• Test Mark: ECE R90 APPROVED
• Manufacturer: ZIMMERMANN

• Fitting Position: Rear Axle
• Width [mm]: 61.8
• Height [mm]: 58.6
• Thickness [mm]: 15
• Brake System: ATE
• Test Mark: E9 90R-02A1242/1617
• MAPP code available:
• Article number of recommended accessories: 13.0460-0186.2, 13.0460-0215.2, 24.8190-0401.2
• Observe dimensions:
• Permissible up to vehicle capacity [kW]: 225
• Name: Piduriklotsi komplekt,ketaspidur
• Manufacturer: ATE

Wear Warning Contact: prepared for wear warning indicator, excl. wear warning contact Technical Information: Technically it is possible to combine ATE Ceramic brake pads with the PowerDisc or with perforated brake discs. The brak ing power with such a pairing is the same as with an origina l ATE brake pad or OE brake pad. However, when the two compo nents interact they can generate more noise in braking. ATE Ceramic brake pads were developed for comfort-oriented drive rs. We therefore recommend using them with normal brake disc s, i.e. smooth ones.

• Alternatively:
• Fitting Position: Front Axle
• Brake System: TEVES
• Width [mm]: 100
• Height [mm]: 73.6
• Thickness [mm]: 16
• WVA Number: 21153
• Wear Warning Contact: excl. wear warning contact
• Supplementary Article/Info 2: without anti-squeak plate
• Test Mark: ECE-R90
• Weight [kg]: 1.61
• Manufacturer: VALEO KLOCKI

• Fitting Position: Front Axle
• Quantity per packing unit: 4
• Manufacturer Restriction: ATE
• Wear Warning Contact: prepared for wear warning indicator
• Test Mark: E9 90R 01705/026
• Height [mm]: 73.5
• Width [mm]: 99.8
• Thickness [mm]: 17.5
• Name: PIDURIKLOTSI KOMPLEKT,KETASPIDUR
• Manufacturer: TRW

SVHC: No information available, please contact the manufacturer!

• Fitting Position: Front Axle
• Supplementary Article/Info 2: with anti-squeak plate
• Observe technical data:
• Material: Low-Metallic
• Test Mark: ECE-R90
• WVA Number: 21153
• Thickness [mm]: 17.5
• Width [mm]: 99.9
• Height [mm]: 73.8
• Brake System: ATE
• Name: PIDURIKLOTSI KOMPLEKT,KETASPIDUR
• Manufacturer: BOS

Article number of recommended accessories: 1987474577, 1987474901, 1987473008, 1987474660, 1987474338, 1987474373, 1987474241

• Filter type: In-Line Filter
• Diameter [mm]: 82
• Height [mm]: 168.5
• Thread Size Entry: M12x1,5
• Thread Size Exit: M14x1,5
• Packaging height [cm]: 17.5
• Net Weight [g]: 336
• Packaging length [cm]: 8.5
• Packaging width [cm]: 8.5
• Name: KN KL38
• Manufacturer: KNECHT

• Filter type: In-Line Filter
• Diameter [mm]: 82
• Height [mm]: 168.5
• Thread Size Entry: M12x1,5
• Thread Size Exit: M14x1,5
• Packaging height [cm]: 17.5
• Net Weight [g]: 336
• Packaging length [cm]: 8.5
• Packaging width [cm]: 8.5
• Manufacturer: MAHLE KNECHT

• Fitting Position: Front Axle
• Quantity per packing unit: 4
• Width [mm]: 100
• Thickness [mm]: 18
• Height [mm]: 73
• Wear Warning Contact: prepared for wear warning indicator
• Supplementary Article/Supplementary Info: without accessories
• Brake System: Teves
• WVA Number: 21153
• Manufacturer: BREMBO
• Name: BR P 50 010

• Fitting Position: Front Axle
• Quantity per packing unit: 4
• Brake System: ATE
• Width [mm]: 99
• Height [mm]: 73
• Thickness [mm]: 18
• Wear Warning Contact: prepared for wear warning indicator
• Supplementary Article/Supplementary Info: Photo corresponds to scope of supply
• Test Mark: ECE R90 APPROVED
• Manufacturer: ZIMMERMANN

• Fitting Position: Front Axle
• Article number of recommended accessories: 98021302, 82032000
• Width [mm]: 99.4
• Height [mm]: 73.3
• Thickness [mm]: 17.5
• Wear Warning Contact: prepared for wear warning indicator
• WVA Number: 21153
• Brake System: Teves
• Packaging length [cm]: 12.5
• Packaging width [cm]: 8.1
• Packaging height [cm]: 8
• Weight [kg]: 1.6
• Name: PIDURIKLOTSI KOMPLEKT,KETASPIDUR
• Manufacturer: TEX

• Fitting Position: Front Axle
• Article number of recommended accessories: 8DK 355 251-991, 8DZ 355 201-211
• Quantity per packing unit: 4
• Width [mm]: 99.4
• Height [mm]: 73.3
• Thickness [mm]: 17.5
• Wear Warning Contact: prepared for wear warning indicator
• WVA Number: 21153
• Brake System: Teves
• Weight [kg]: 1.6
• Assy./disassy. by qualified personnel required!:
• Name: HE 8DB355007471
• Manufacturer: HELLA PAGID

• Fitting Position: Front Axle
• Width [mm]: 99.8
• Height [mm]: 73.6
• Thickness [mm]: 17.5
• Brake System: ATE
• Test Mark: E9 90R-02A1162/0452
• MAPP code available:
• Article number of recommended accessories: 13.0460-0219.2, 13.0460-0268.2, 24.8190-0401.2
• Observe dimensions:
• Name: PIDURIKLOTSI KOMPLEKT,KETASPIDUR
• Manufacturer: ATE
• Quality class: Q

Wear Warning Contact: prepared for wear warning indicator, excl. wear warning contact