• Transmission Type: Manual Transmission
• Fabrication Number: ECS-AU-000
• Manufacturer: NTY

Exhaust System: for vehicles with factory fitted soot -/particulate filter

• Number of pins: 3
• Material: Plastic
• Diameter 1 [mm]: 6
• Diameter 2 [mm]: 8
• Fabrication Number: ECS-AU-004
• Manufacturer: NTY

• Number of pins: 3
• Diameter 1 [mm]: 6
• Diameter 2 [mm]: 8
• Fabrication Number: ECS-PL-002
• Manufacturer: NTY

• Transmission Type: Automatic Transmission
• Fabrication Number: ECS-ME-000
• Manufacturer: NTY

• Socket colour: black
• Plug Type: Female
• Number of pins: 3
• Number of used contacts: 3
• Number of circuits: 3
• Cable Cross Section [mm²]: 0.75
• Cable Length [mm]: 700
• Supplementary Article/Supplementary Info: with shrink squeeze connector
• Material: CuSn (copper-tin)
• Cable insulation material: Silicone
• Manufacturer: METZGER

• Exhaust System: before soot particulate filter
• Connector Shape: D Shape
• Number of pins: 3
• Pressure [Pa] from: 0
• Pressure [Pa] to: 105,000
• Manufacturer: NRF

• Number of pins: 3
• Manufacturer: JPN

• Number of pins: 3
• Pressure [Pa] from: 2,000
• Pressure [Pa] to: 108,000
• Colour: black
• Material: Plastic
• Manufacturer: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Exhaust System: before soot particulate filter
• Voltage [V]: 12
• Supplementary Article/Supplementary Info: without cable pull
• Number of pins: 3
• Guarantee: 3 years guarantee
• Weight [kg]: 0.04
• Operating Mode: Electric
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 17SKV335

• Number of connectors: 3
• Fabrication Number: ECS-ME-005
• Manufacturer: NTY

• Exhaust System: for two-part exhaust system
• Emission Standard: Euro 5
• Connector Shape: oval
• Number of pins: 3
• Pressure [Pa] from: 50,000
• Pressure [Pa] to: 600,000
• Manufacturer: NRF

• for OE number: 642 905 01 00
• Guarantee: 3 years guarantee
• Voltage [V]: 12
• Weight [g]: 100
• Length [mm]: 69
• Width [mm]: 72
• Height [mm]: 39
• Housing material: Plastic
• Operating Mode: Electric
• Connector Shape: D Shape
• Number of pins: 3
• Manufacturer: AT AUTOTEILE GERMANY

General Information: Products and spare parts supplied by us are only intended for the designated use. Installation may only be carried out by trained specialist personnel. Our products are not always supplied with installation instructions. Improper installation or inappropriate use may lead to the exclusion of warranty.

• Engine Code: OM 651.912
• Exhaust System: before soot particulate filter
• Output Voltage, from [V]: 0.5
• Output Voltage, up to [V]: 4.5
• Supplementary Article/Info 2: without fastening clamp
• Manufacturer: FACET

• Manufacturer: BOSCH
• Name: BS 0281006278

• Number of pins: 3
• Guarantee: 3 years guarantee
• Weight [kg]: 0.05
• Always compare old and new part (in particular OE No.):
• Name: CE 17SKV661
• Manufacturer: ESEN SKV

• for OE number: 009 153 52 28
• Number of connectors: 3
• Fabrication Number: ECS-ME-003
• Manufacturer: NTY

• for OE number: A 008 153 22 28, A 000 905 64 04
• Number of pins: 2
• Fabrication Number: EGT-ME-001
• Cable Length [mm]: 300
• Manufacturer: NTY

• Fabrication Number: EGT-ME-011
• Cable Length [mm]: 150
• Manufacturer: NTY

• Engine Code: OM 651.912
• Exhaust System: before soot particulate filter
• Output Voltage, from [V]: 0.5
• Output Voltage, up to [V]: 4.5
• Supplementary Article/Info 2: without fastening clamp
• Name: EP 1.993.269
• Manufacturer: EPS

• Quality: OE EQUIVALENT
• for OE number: 6429050100
• Manufacturer: MEAT&DORIA

• Number of pins: 3
• Guarantee: 3 years guarantee
• Weight [kg]: 0.05
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 17SKV778

• Length [mm]: 46.4
• Thread Size: M12x1,5 mm
• Material: Plastic
• Number of pins: 3
• Guarantee: 3 years guarantee
• Height [mm]: 23.9
• Weight [kg]: 0.05
• Housing material: Aluminium
• Pressure from [kPA]: 0
• Pressure to [kPA]: 600
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY
• Name: CE 17SKV780

• Number of connectors: 3
• Material: Plastic
• Sensor Type: Differential Pressure Sensor
• Weight [kg]: 0.033
• Manufacturer: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Exhaust System: for two-part exhaust system
• Emission Standard: Euro 6
• Connector Shape: oval
• Number of pins: 3
• Pressure [Pa] from: 50,000
• Pressure [Pa] to: 700,000
• Manufacturer: NRF

• Emission Standard: Euro 5
• Number of pins: 3
• Opening pressure [kPa]: 1.1
• Name: DE DPS00041-12B1
• Manufacturer: DELPHI

• Number of connectors: 3
• Material: Plastic
• Sensor Type: Differential Pressure Sensor
• Name: SW 10 94 3587
• Manufacturer: SWAG
• Lisainfo: 10 94 3587 SWA
• Additional information: 10 94 3587 SWA

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Number of connectors: 3
• Manufacturer: FAST

• Number of pins: 3
• Pressure [Pa] from: 50,000
• Pressure [Pa] to: 700,000
• Manufacturer: FAE ELEKTRYKA

• Number of pins: 3
• Guarantee: 5 years guarantee
• General Information: Sold in Hueco brand: printing and packaging
• Name: HU 137403
• Manufacturer: HUECO / HITACHI

Exhaust System: for vehicles with factory fitted soot -/particulate filter

• Number of pins: 3
• Pressure [Pa] from: 2,000
• Pressure [Pa] to: 108,000
• Manufacturer: FAE

• Exhaust System: before soot particulate filter
• Mounting Type: Bolted
• Number of pins: 3
• Assy./disassy. by qualified personnel required!:
• SVHC: 7439-92-1; Lead
• Name: HE 6PP009409171
• Manufacturer: HELLA

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Construction Year from: 06.2013
• Left-/right-hand drive vehicles: for right-hand drive vehicles
• Supplementary Article/Info 2: with cable
• Cable Length [mm]: 370
• Overall Length [mm]: 470
• Number of pins: 2
• Connector Shape: oval
• Socket colour: black
• Thread Size: M14 x 1,5
• Spanner Size: 17
• Sensor Type: PTC
• Manufacturer: VALEO

• Number of pins: 3
• Manufacturer: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Construction Year from: 06.2013
• Supplementary Article/Info 2: with cable
• Cable Length [mm]: 300
• Overall Length [mm]: 455
• Number of pins: 2
• Connector Shape: oval
• Socket colour: black
• Thread Size: M14 x 1,5
• Spanner Size: 17
• Sensor Type: PTC
• Manufacturer: VALEO

• Colour: black
• Alternatively:
• Number of connectors: 3
• Alternative Repair Kit: 550627
• Manufacturer: ERA

• not for special equipment code: 929K, 930K, 940K, F205, F222
• for OE number: 009 153 51 28
• Weight [kg]: 0.04
• Number of pins: 3
• Connector Shape: oval
• Socket colour: black
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

Manufacturer: MAGNETI MARELLI

• Number of pins: 3
• Connector Shape: oval
• Socket colour: black
• Manufacturer: FAST

• Number of pins: 3
• Pressure [Pa] to: 600,000
• Socket colour: black
• Manufacturer: FAE ELEKTRYKA

• Number of pins: 3
• Opening pressure [kPa]: 98.8
• Manufacturer: DELPHI

• Number of pins: 3
• Connector Shape: oval
• Socket colour: black
• for OE number: 6519050200
• Manufacturer: MEAT&DORIA

• not for special equipment code: 929K, 930K, 940K, F205, F222
• Number of pins: 3
• Fitting Position: EGR Valve
• Version: IAM
• Manufacturer: METZGER

• Required quantity: 1
• Fitting Position: before soot particulate filter
• Connector Shape: oval
• Number of pins: 2
• Voltage [V]: 12
• Fitting Depth [mm]: 50
• Cable Length [mm]: 400
• Thread Size: M14x1.5
• Supplementary Article/Supplementary Info: with synthetic grease
• Manufacturer: NRF

• Required quantity: 1
• Fitting Position: before soot particulate filter
• Connector Shape: oval
• Number of pins: 2
• Voltage [V]: 12
• Fitting Depth [mm]: 50
• Cable Length [mm]: 215
• Thread Size: M14x1.5
• Supplementary Article/Supplementary Info: with synthetic grease
• Manufacturer: NRF

• Engine Code: OM 651.912
• Emission Standard: Euro 6
• Fitting Position: after EGR cooler
• Thread Size: M12x1,5
• Spanner Size: 24
• Manufacturer: FACET

• External Thread Size: M14 x 1,5
• Number of connectors: 2
• Fitting Position: before exhaust turbocharger
• Cable Length [mm]: 230
• Weight [kg]: 0.035
• Manufacturer: FEBI

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Required quantity: 1
• Fitting Position: before exhaust turbocharger
• Connector Shape: oval
• Number of pins: 2
• Voltage [V]: 12
• Fitting Depth [mm]: 41
• Cable Length [mm]: 294
• Thread Size: M14x1.5
• Supplementary Article/Supplementary Info: with synthetic grease
• Manufacturer: NRF

• Exhaust System: before turbocharger
• Length [mm]: 300
• Thread Size: M14 x 1,5
• Number of pins: 2
• Manufacturer: JPN

Manufacturer: AUTO-GH

• Fitting Position: after EGR cooler
• Emission Standard: Euro 5
• Mounting Type: Screw Connection
• Number of pins: 3
• Assy./disassy. by qualified personnel required!:
• Name: HE 6PP009409611
• Manufacturer: HELLA

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Voltage [V]: 12
• Cable Length [mm]: 300
• Number of pins: 2
• Guarantee: 3 years guarantee
• Weight [kg]: 0.09
• Operating Mode: Electric
• Always compare old and new part (in particular OE No.):
• Name: CE 30SKV128
• Manufacturer: ESEN SKV

• Number of pins: 3
• Connector Shape: oval
• for OE number: 0091535228
• Manufacturer: MEAT & DORIA

• for OE number: A0061539528
• Manufacturer: MEAT&DORIA

• Number of connectors: 3
• Weight [kg]: 0.06
• for OE number: 009 153 51 28
• Manufacturer: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Number of pins: 3
• Version: IAM
• Article number of recommended accessories: 2324232
• Manufacturer: METZGER

Exhaust System: for vehicles with factory fitted soot -/particulate filter

• Fitting Position: Exhaust Turbocharger
• Thread Size: M14x1,5
• Cable Length [mm]: 327
• Socket colour: black, white
• Manufacturer: FAE

• Required quantity: 1
• Fitting Position: before soot particulate filter
• Supplementary Article/Supplementary Info: with synthetic grease
• Manufacturer: NRF

• Cable Length [mm]: 170
• Manufacturer: FAST

• Required quantity: 1
• Fitting Position: before soot particulate filter
• for OE number: A0081532728
• Supplementary Article/Supplementary Info: with synthetic grease
• Manufacturer: NRF

• Emission Standard: Euro 6
• Alternatively:
• Number of pins: 3
• Opening pressure [kPa]: 49
• Name: DE DPS00034-12B1
• Manufacturer: DELPHI

• Required quantity: 1
• Fitting Position: before soot particulate filter
• Connector Shape: oval
• Number of pins: 2
• Voltage [V]: 12
• Fitting Depth [mm]: 50
• Cable Length [mm]: 374
• Thread Size: M14x1.5
• Supplementary Article/Supplementary Info: with synthetic grease
• Manufacturer: NRF

• Fitting Position: Catalytic Converter
• External Thread Size: M14 x 1,5
• Spanner Size: 17
• Number of connectors: 2
• Cable Length [mm]: 400
• Weight [kg]: 0.07
• for OE number: 000 905 43 05
• Manufacturer: FEBI

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Number of pins: 3
• Number of connectors: 3
• Connector Shape: oval
• Socket colour: black
• Manufacturer: ERA

• Fitting Position: Catalytic Converter
• External Thread Size: M14 x 1,5
• Spanner Size: 17
• Number of connectors: 2
• Cable Length [mm]: 401
• Weight [kg]: 0.07
• Manufacturer: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Number of connectors: 3
• Weight [kg]: 0.034
• for OE number: 009 153 52 28
• Name: SW 33 10 0824
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• for special equipment code: F091, F117, F156, F176, F246
• Number of pins: 3
• Fitting Position: EGR Valve
• Version: OE
• Manufacturer: METZGER

• Number of connectors: 2
• Fitting Position: before exhaust turbocharger
• Weight [kg]: 0.07
• for OE number: 000 905 64 04
• Manufacturer: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Exhaust System: before turbocharger
• Emission Standard: Euro 5
• Vehicle configuration line / variant: BLUETEC(-)
• Cable Length [mm]: 300
• Number of pins: 2
• Manufacturer: DELPHI
• Name: DE TS30098

• Fitting Position: before soot particulate filter
• Number of connectors: 3
• Manufacturer: ERA

• Number of connectors: 2
• Fitting Position: before exhaust turbocharger
• Weight [kg]: 0.07
• for OE number: 000 905 64 04
• Name: SW 10 94 8839
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Cable Length [mm]: 300
• Number of pins: 2
• Quality: OE EQUIVALENT
• for OE number: A0081532228
• Manufacturer: MEAT & DORIA

• Fitting Position: Catalytic Converter
• External Thread Size: M14 x 1,5
• Spanner Size: 17
• Number of connectors: 2
• Cable Length [mm]: 400.5
• Weight [kg]: 0.07
• Name: SW 10 10 0823
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Fitting Position: before soot particulate filter
• Required quantity: 1
• Assy./disassy. by qualified personnel required!:
• Mounting Type: Bolted
• Number of pins: 2
• Cable Length [mm]: 1,100
• Name: HE 6PT358181441
• Manufacturer: HELLA

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Fitting Position: before exhaust turbocharger
• Required quantity: 1
• Mounting Type: Bolted
• Number of pins: 2
• Cable Length [mm]: 295
• Assy./disassy. by qualified personnel required!:
• Manufacturer: HELLA
• Name: HE 6PT010376131

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Fitting Position: before catalytic converter
• Emission Standard: Euro 6
• Manufacturer: BOSCH