Manufacturer: MAGNETI MARELLI

• Thread Size: M 12x1,5
• Number of pins: 2
• Colour: grey
• Supplementary Article/Supplementary Info: with seal
• Power [W]: 0.06
• Manufacturer: METZGER

• Sensor Type: Passive sensor
• Manufacturer: KAMOKA

• Construction Year to: 09.2000
• Height [mm]: 34
• Weight [kg]: 0.04
• Number of connectors: 2
• Required quantity: 1
• Supplementary Article/Info 2: for camshaft, without cable
• Resistor [Ohm]: 450
• Colour: black
• Operating Mode: Electric
• Sensor Type: Inductive Sensor
• Number of pins: 2
• Rated Voltage [V]: 12
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Number of pins: 2
• Housing Colour: grey
• Thread Size: M 12x1,5
• Manufacturer: FAE

• Required quantity: 1
• Sensor Type: Inductive Sensor
• Number of pins: 2
• Supplementary Article/Info 2: without cable
• Manufacturer: FAST

• Construction Year from: 09.2000
• Number of pins: 2
• Supplementary Article/Info 2: without cable
• Sensor Type: Inductive Sensor
• for OE number: 5L2E 6B288 AA
• Manufacturer: MEAT&DORIA

• Number of pins: 2
• Manufacturer: FAE

• Lambda Sensor: Lambda Sensor, Thread pre-greased
• Fabrication Number: ESL-UV-001
• Manufacturer: NTY
• Name: NTY ESL-UV-001

• Number of circuits: 4
• Lambda Sensor: Regulating Probe
• Manufacturer: KAMOKA

• Length [mm]: 373
• Number of pins: 4
• Lambda Sensor: Thread pre-greased
• Fabrication Number: ESL-FR-008

Lisainfo: ENG. 1,4,1.6,1.8,2.0 FORD FOCUS 04-, C-MAX 07-, MONDEO IV 07-15, GALAXY II 06-15, S-MAX 06-14, VOLVO C30 06-12, S40 II 04-12, S60 II 10-14, S80 II 08-16, XC60 09-17 /REGULACYJNA, Dœ.CAœK. 373MM Additional information: ENG. 1,4,1.6,1.8,2.0 FORD FOCUS 04-, C-MAX 07-, MONDEO IV 07-15, GALAXY II 06-15, S-MAX 06-14, VOLVO C30 06-12, S40 II 04-12, S60 II 10-14, S80 II 08-16, XC60 09-17 /REGULACYJNA, Dœ.CAœK. 373MM

• Construction Year from: 09.2000
• Voltage [V]: 12
• Supplementary Article/Supplementary Info: without cable pull
• Number of pins: 2
• Weight [kg]: 0.05
• Operating Mode: Electric
• Warranty: 3 years warranty
• Always compare old and new part (in particular OE No.):
• Manufacturer: ESEN SKV

• Lambda Sensor: Lambda Sensor
• Length [mm]: 373
• Number of pins: 4
• Warranty: 3 years warranty
• Always compare old and new part (in particular OE No.):
• Manufacturer: SKV GERMANY

• Lambda Sensor: Lambda Sensor
• Weight [kg]: 0.12
• Warranty: 3 years warranty
• Always compare old and new part (in particular OE No.):
• Name: CE 09SKV121
• Manufacturer: ESEN SKV

• Construction Year from: 09.1999
• Construction Year to: 08.2001
• Lambda Sensor: Regulating Probe
• Fitting Position: before catalytic converter
• Required quantity: 2
• Number of circuits: 4
• Overall Length [mm]: 422
• Available as universal article as well, see article no.: 0258986602
• Recommended change interval [km]: 250,000
• Manufacturer: BOSCH
• Name: BS 0258986603

• Construction Year from: 09.1997
• Construction Year to: 09.1998, 09.2000
• Lambda Sensor: Regulating Probe, Diagnostic Probe
• Block Separation:
• Alternatively:
• Number of circuits: 4
• Overall Length [mm]: 422
• Available as universal article as well, see article no.: 0258005729
• Recommended change interval [km]: 160,000
• Manufacturer: BOSCH

Fitting Position: before catalytic converter, Right, after catalytic converter

• Construction Year to: 08.1998
• Lambda Sensor: Regulating Probe, Heated
• Required quantity: 2
• Number of pins: 4
• Cable Length [mm]: 670
• for article number: 81029E
• Quality: OE EQUIVALENT
• Manufacturer: MEAT&DORIA

• Construction Year from: 09.1997
• Construction Year to: 09.1998
• Fitting Position: Right, before catalytic converter
• Lambda Sensor: Regulating Probe, Heated
• External Thread Size: M18 x 1,5
• Spanner Size: 22
• Number of circuits: 4
• Cable Length [mm]: 400
• Weight [kg]: 0.094
• for OE number: CA09-18-861
• Name: SW 33 10 3762
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Construction Year to: 08.1998
• Lambda Sensor: Regulating Probe, Finger probe, Thread pre-greased
• Required quantity: 2
• Line insulation design: with silicone-coated woven-fibre insulation
• Length [mm]: 430
• Number of pins: 4
• Weight [kg]: 0.129
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Construction Year from: 09.1999
• Construction Year to: 08.2001
• Fitting Position: before catalytic converter
• Required quantity: 2
• Lambda Sensor: Regulating Probe, Heated
• External Thread Size: M18 x 1,5
• Spanner Size: 22
• Number of circuits: 4
• Cable Length [mm]: 400
• Weight [kg]: 0.085
• for OE number: 1 300 544
• Name: SW 33 10 3139
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Resistor [Ohm]: 9
• Conductor Number: 4
• Number of circuits: 4
• Length [mm]: 400
• Cable Length [mm]: 400
• Lambda Sensor: Heated
• Name: MM OSM099
• Manufacturer: MAGNETI MARELLI

• Construction Year to: 08.1999, 08.1997, 08.2001
• Lambda Sensor: Diagnostic Probe, Regulating Probe
• Camshaft: SOHC/OHC
• Block Separation:
• Construction Year from: 09.1997
• Required quantity: 2
• Number of circuits: 4
• Recommended change interval [km]: 160,000
• Connector/Clamp: Connector may need adjustment
• Manufacturer: BOSCH
• Name: BS 0258986507

Fitting Position: after catalytic converter, before catalytic converter

• Construction Year to: 08.2001
• Lambda Sensor: Heated
• Number of pins: 4
• Cable Length [mm]: 290
• for article number: 81718E
• Quality: OE EQUIVALENT
• Manufacturer: MEAT&DORIA

• Construction Year from: 09.1997
• Construction Year to: 09.1998, 09.2000
• Lambda Sensor: Regulating Probe, Diagnostic Probe
• Block Separation:
• Alternatively:
• Number of circuits: 4
• Recommended change interval [km]: 160,000
• Connector/Clamp: Connector may need adjustment
• Manufacturer: BOSCH

Fitting Position: before catalytic converter, Left, Right, after catalytic converter

• Construction Year from: 09.1999
• Construction Year to: 08.2001
• Quantity: 2
• Fitting Position: before catalytic converter
• Line insulation design: with silicone-coated woven-fibre insulation
• Lambda Sensor: Planar probe, Heated, Thread pre-greased
• Cable Length [mm]: 210
• Number of circuits: 4
• Weight [kg]: 0.09
• Manufacturer: VEMO GERMANY

Supplementary Article/Supplementary Info: with squeeze connector, with shrink squeeze connector General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Construction Year from: 10.1998
• Construction Year to: 09.2000
• Lambda Sensor: Regulating Probe
• Fitting Position: before catalytic converter
• Number of circuits: 4
• Recommended change interval [km]: 160,000
• Connector/Clamp: Connector may need adjustment
• Manufacturer: BOSCH

• Construction Year to: 08.1998
• Lambda Sensor: Regulating Probe, Planar probe, Thread pre-greased
• Required quantity: 2
• Line insulation design: with silicone-coated woven-fibre insulation
• Length [mm]: 750
• Number of pins: 4
• Weight [kg]: 0.151
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Construction Year from: 09.1999
• Construction Year to: 08.2001
• Lambda Sensor: Regulating Probe
• Fitting Position: before catalytic converter
• Required quantity: 2
• Number of circuits: 4
• Recommended change interval [km]: 160,000
• Connector/Clamp: Connector may need adjustment
• Manufacturer: BOSCH

• Construction Year from: 09.1998
• Lambda Sensor: Regulating Probe, Thread pre-greased
• Required quantity: 2
• Line insulation design: with silicone-coated woven-fibre insulation
• Thread Size: M18 x 1,5
• Cable Length [mm]: 320
• Conductor Number: 4
• Connector Shape: round
• Length [mm]: 450
• Number of pins: 4
• Weight [kg]: 0.13
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Construction Year to: 08.2001
• Lambda Sensor: Heated
• Number of pins: 4
• Cable Length [mm]: 290
• for article number: 81718
• Manufacturer: MEAT&DORIA

• Construction Year from: 10.1998
• Construction Year to: 09.2000
• Lambda Sensor: Regulating Probe, Diagnostic Probe
• Block Separation:
• Length [mm]: 450
• Number of circuits: 4
• Manufacturer: VDO

Fitting Position: before catalytic converter, after catalytic converter