• Inner Diameter [mm]: 14
• Outer Diameter [mm]: 20
• Thickness [mm]: 2
• Material: Copper
• Shape: C Shape
• DIN/ISO: 7603
• Alternative Repair Kit: 017.736, 036.400, 505.550, 505.540
• Manufacturer: ELRING
• Lisainfo: 813.036 ELR
• Additional information: 813.036 ELR

• Thickness [mm]: 2
• Inner Diameter [mm]: 14
• Outer Diameter [mm]: 21
• Material: Copper
• Weight [kg]: 0.05
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Thickness [mm]: 2
• Inner Diameter [mm]: 14
• Outer Diameter [mm]: 21
• Material: Copper
• Weight [kg]: 0.05
• Manufacturer: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Thickness [mm]: 2
• Inner Diameter [mm]: 14
• Outer Diameter [mm]: 21
• Weight [kg]: 0.001
• Fitting Position: Oil Sump
• Manufacturer: VAICO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Inner Diameter [mm]: 10
• Outer Diameter [mm]: 21
• Thickness [mm]: 2.1
• Material: Copper
• Shape: A Shape
• Alternative Repair Kit: 505.540
• Manufacturer: ELRING
• Lisainfo: 108.502 ELR
• Additional information: 108.502 ELR

• Thickness [mm]: 2
• Inner Diameter [mm]: 10
• Outer Diameter [mm]: 20
• Material: Copper
• Weight [kg]: 0.05
• Name: RONGASTIHEND, OLI ŽRAVOOLUKRUVI
• Manufacturer: FEB

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Thickness [mm]: 2
• Inner Diameter [mm]: 10.2
• Outer Diameter [mm]: 20
• Material: Copper
• Weight [kg]: 0.001
• Fitting Position: Oil Sump
• Manufacturer: VAICO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Material: Steel
• Length [mm]: 17
• Thread Length [mm]: 13
• Quality/ Grade: 8.8
• Spanner Size: 21
• Bolt Head-/Nut Design: Male Hex
• Surface: Zinc-coated
• for OE number: 1146063
• Manufacturer: DELLO AUTOMEGA

• Engine Code: RHY (DW10TD)
• Thickness [mm]: 2
• Inner Diameter [mm]: 14.5
• Outer Diameter [mm]: 19
• Name: RONGASTIHEND, OLI ŽRAVOOLUKRUVI
• Manufacturer: AJU

• Length [mm]: 17
• External Thread Size: M10 x 1,25
• Thread Length [mm]: 13
• Quality/ Grade: 8.8
• Spanner Size: 21
• Bolt Head-/Nut Design: Male Hex
• Material: Steel
• Surface: Zinc-coated
• Screw length below head [mm]: 13
• Weight [kg]: 0.15
• Supplementary Article/Info 2: without seal ring
• Name: SULGURKRUVI, OLIVANN
• Manufacturer: FEB

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Length [mm]: 13
• External Thread Size: M10 x 1,25
• Thread Length [mm]: 13
• Quality/ Grade: 8.8
• Spanner Size: 21
• Bolt Head-/Nut Design: Male Hex
• Material: Steel
• Surface: Zinc-coated
• Screw length below head [mm]: 13
• Weight [kg]: 0.15
• Supplementary Article/Info 2: without seal ring
• Manufacturer: FEBI

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Length [mm]: 17
• External Thread Size: M10 x 1,25
• Thread Length [mm]: 13
• Quality/ Grade: 8.8
• Spanner Size: 21
• Bolt Head-/Nut Design: Male Hex
• Material: Steel
• Surface: Zinc-coated
• Screw length below head [mm]: 13
• Weight [kg]: 0.15
• Supplementary Article/Info 2: without seal ring
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Inner Diameter [mm]: 14.7
• Outer Diameter [mm]: 22
• Material: Rubber/Metal
• Shape: round
• Thickness [mm]: 1.5
• Packing Type: Blister Pack
• Manufacturer: CORTECO

• Thread Size: M14x1,25
• Length [mm]: 13
• Additionally required articles (article numbers): 253.550.100
• Name: SULGURKRUVI, OLIVANN
• Manufacturer: FIS

• Thread Size: M14x1.25
• Length [mm]: 13
• Supplementary Article/Info 2: with seal ring
• Name: SULGURKRUVI, OLIVANN
• Manufacturer: FIS

• Thread Size: M10x1,25x13
• Spanner Size: 21 mm
• Bolt Head-/Nut Design: Male Hex
• Supplementary Article/Info 2: with seal ring
• Manufacturer: DR.MOTOR AUTOMOTIVE

• Length [mm]: 17
• External Thread Size: M10 x 1,25
• Thread Length [mm]: 10
• Quality/ Grade: 8.8
• Spanner Size: 21
• Bolt Head-/Nut Design: Male Hex
• Screw length below head [mm]: 11
• Seal Diameter [mm]: 20.4
• Weight [kg]: 0.2
• Supplementary Article/Info 2: with seal ring
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• for OE number: 0313.27, 11131742994
• Vehicle Equipment: for vehicles with air conditioning
• Inner Diameter [mm]: 14.3
• Outer Diameter [mm]: 20
• Material: Copper
• Thickness [mm]: 2
• Packing Type: Blister Pack
• Manufacturer: CORTECO

• Thread Size: M10x1,25
• Length [mm]: 13
• Supplementary Article/Info 2: with seal ring
• Name: SULGURKRUVI, OLIVANN
• Manufacturer: FIS

• Length [mm]: 17
• External Thread Size: M10 x 1,25
• Thread Length [mm]: 10
• Quality/ Grade: 8.8
• Spanner Size: 21
• Bolt Head-/Nut Design: Male Hex
• Screw length below head [mm]: 11
• Seal Diameter [mm]: 20
• Weight [kg]: 0.02
• Supplementary Article/Info 2: with seal ring
• Name: SULGURKRUVI, OLIVANN
• Manufacturer: BLP

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Length [mm]: 17
• External Thread Size: M10 x 1,25
• Thread Length [mm]: 10
• Quality/ Grade: 8.8
• Spanner Size: 21
• Bolt Head-/Nut Design: Male Hex
• Screw length below head [mm]: 11
• Seal Diameter [mm]: 20.4
• Weight [kg]: 0.2
• Supplementary Article/Info 2: with seal ring
• Name: SULGURKRUVI, OLIVANN
• Manufacturer: FEB

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Length [mm]: 17
• External Thread Size: M10 x 1,25
• Thread Length [mm]: 13
• Quality/ Grade: 8.8
• Spanner Size: 21
• Bolt Head-/Nut Design: Male Hex
• Material: Steel
• Surface: Zinc-coated
• Screw length below head [mm]: 13
• Weight [kg]: 0.15
• for OE number: 0311.29
• Manufacturer: ENERGY

• Thread Size: M10x1,25
• Length [mm]: 13
• Additionally required articles (article numbers): 746.520.100
• Manufacturer: FA1 FISCHER

• Thread Size: M10x1,25x13
• Bolt Head-/Nut Design: Male Hex
• Spanner Size: 21 mm
• Alternative Repair Kit: 877.930
• Supplementary Article/Info 2: without seal ring
• Manufacturer: ELRING

• Vehicle Equipment: for vehicles without air conditioning
• Thread Size: M10 x 1,25
• Screw length below head [mm]: 13
• Bolt Head-/Nut Design: Male Hex
• Spanner Size: 21
• Supplementary Article/Info 2: with seal ring
• Manufacturer: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Vehicle Equipment: for vehicles with air conditioning
• Length [mm]: 17
• Required quantity: 1
• External Thread [mm]: M14 x 1,25
• Thread Length [mm]: 11
• Thread Size: M14 x 1,25
• Thread Pitch [mm]: 1.25
• Fitting Position: engine sided
• Spanner Size: 21
• Bolt Head-/Nut Design: Hexagon Socket
• Surface: Zinc-coated
• Supplementary Article/Info 2: with seal ring
• Weight [kg]: 0.021
• Manufacturer: VAICO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Vehicle Equipment: for vehicles with air conditioning
• Length [mm]: 17.3
• External Thread Size: M14 x 1,25
• Thread Length [mm]: 11
• Quality/ Grade: 8.8
• Spanner Size: 21, 8
• Bolt Head-/Nut Design: Hexagon Socket, Male Hex
• Material: Steel
• Surface: Zink-nickel coated
• Screw length below head [mm]: 13
• Weight [kg]: 0.023
• Supplementary Article/Info 2: without seal ring
• Manufacturer: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Vehicle Equipment: for vehicles with air conditioning
• Thread Size: M14 x 1,25
• Bolt Head-/Nut Design: Male Hex, Hexagon Socket
• Spanner Size: 21, 8
• Length [mm]: 17
• Thread Length [mm]: 12.5
• Supplementary Article/Info 2: with seal ring
• Manufacturer: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Vehicle Equipment: for vehicles with air conditioning
• Length [mm]: 17.3
• External Thread Size: M14 x 1,25
• Thread Length [mm]: 11
• Quality/ Grade: 8.8
• Spanner Size: 21, 8
• Bolt Head-/Nut Design: Hexagon Socket, Male Hex
• Material: Steel
• Surface: Zink-nickel coated
• Screw length below head [mm]: 13
• Supplementary Article/Info 2: without seal ring
• Name: SW 62 94 7129
• Manufacturer: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Vehicle Equipment: for vehicles without air conditioning
• Length [mm]: 18
• Thread Size: M 10 x 1,25 x 12,5
• Spanner Size: 21
• Supplementary Article/Info 2: with seal ring
• Packing Type: Blister Pack
• Name: SULGURKRUVI, OLIVANN
• Manufacturer: COT

• Vehicle Equipment: for vehicles with air conditioning
• Length [mm]: 17.3
• External Thread Size: M14 x 1,25
• Thread Length [mm]: 11
• Quality/ Grade: 8.8
• Spanner Size: 21, 8
• Bolt Head-/Nut Design: Male Hex, Hexagon Socket
• Material: Steel
• Surface: Zink-nickel coated
• Screw length below head [mm]: 13
• Supplementary Article/Info 2: with seal ring
• Manufacturer: SWAG
• Name: SW 62 94 7130

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Thread Size: M10x1,25x13
• Bolt Head-/Nut Design: Male Hex
• Spanner Size: 21 mm
• Supplementary Article/Info 2: with seal ring
• Manufacturer: ELRING

• Thread Size: M14x1,25x13
• Bolt Head-/Nut Design: Hexagon Socket
• Supplementary Article/Info 2: with seal ring
• Manufacturer: ELRING

• Vehicle Equipment: for vehicles with air conditioning
• Length [mm]: 17.3
• External Thread Size: M14 x 1,25
• Thread Length [mm]: 11
• Quality/ Grade: 8.8
• Spanner Size: 21, 8
• Bolt Head-/Nut Design: Male Hex, Hexagon Socket
• Material: Steel
• Surface: Zink-nickel coated
• Screw length below head [mm]: 13
• Weight [kg]: 0.038
• Supplementary Article/Info 2: with seal ring
• Name: SULGURKRUVI, OLIVANN
• Manufacturer: FEB

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Length [mm]: 13
• Thread Size: M14x1.25
• Supplementary Article/Info 2: with seal ring
• Manufacturer: FAST

• Vehicle Equipment: for vehicles with air conditioning
• Length [mm]: 17
• Thread Size: M 14 x 1,25 x 12,5
• Spanner Size: 21
• Supplementary Article/Info 2: with seal ring
• Packing Type: Blister Pack
• Name: SULGURKRUVI, OLIVANN
• Manufacturer: COT

• Inner Diameter [mm]: 14
• Outer Diameter [mm]: 20
• Thickness [mm]: 2
• Shape: C Shape
• Material: Copper
• Alternatively:
• Name: Rongastihend
• Manufacturer: FIS

• Inner Diameter [mm]: 10
• Outer Diameter [mm]: 20
• Thickness [mm]: 2
• Shape: A Shape
• Material: Copper
• Alternatively:
• Name: Rongastihend
• Manufacturer: FIS

• Inner Diameter [mm]: 10
• Outer Diameter [mm]: 21
• Thickness [mm]: 2
• Shape: A Shape
• Material: Copper
• Alternatively:

• Material: ACM (Polyacrylate)
• Thickness [mm]: 64
• Manufacturer: FAST

• Inner Diameter [mm]: 14
• Outer Diameter [mm]: 20
• Thickness [mm]: 2
• Shape: C Shape
• Material: Copper
• Name: Rongastihend
• Manufacturer: FIS

• Inner Diameter [mm]: 10
• Outer Diameter [mm]: 20
• Thickness [mm]: 2
• Shape: A Shape
• Material: Copper
• Manufacturer: FA1 FISCHER

• Inner Diameter [mm]: 10
• Outer Diameter [mm]: 21
• Thickness [mm]: 2
• Shape: A Shape
• Material: Copper
• Manufacturer: FIS

Name: PODKADKA,USZCZELKA MIEDZIANA CU 10,00 X 21,00 X 2,00 (OPAKOWANIE 100 SZT.)