• Switch point from [bar]: 0.3
• Switch point to [bar]: 0.55
• Length [mm]: 51
• Inner Diameter [mm]: 3.1
• External Thread [mm]: M10 x 1
• Thread Length [mm]: 13
• Spanner Size: 24
• Number of connectors: 1
• Colour Coding: blue
• Tootja: JP GROUP
• Lisainfo: Oil pressure switch, 0.3-0.55 Bar

• Number of pins: 2
• Housing Colour: light blue
• Connector Shape: oval
• Tootja: JP GROUP
• Lisainfo: Sender Unit, coolant temperature

• Lambda andur: Diagnoosisond
• for OE number: 46750243
• Quality: OE
• Manufacturer Restriction: DENSO
• Thread Size: M18x1.5
• Cable Length [mm]: 630
• Number of pins: 4
• Weight [g]: 122
• Gross Weight [g]: 155
• Tootja: DENSO

Oxygen Sensor: Heated, Planar probe, Thread pre-greased, Oxygen Sensor Lisainfo: "Tootja: DENSO
MAREA WEEKEND (185),
(kvaliteediklass: Q)"

• Connector Shape: round
• Operating Mode: Hydraulic
• Thread Size: M 10
• Thread Pitch [mm]: 1
• Number of pins: 1
• Switch point from [bar]: 0.3
• Switch point to [bar]: 0.55
• Supplementary Article/Info 2: with seal ring
• Tootja: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Pressure to [bar]: 0.5
• Thread Size: M10 x 1
• Pressure from [bar]: 0.4
• for OE number: 55354325
• Tootja: MEAT & DORIA

• Mootorikood: 192 B3.000
• Pressure [bar]: 0.5
• Thread Size: M10x1
• Spanner Size: 24
• Tootja: FACET

• Mootorikood: 192 B3.000
• Pressure [bar]: 0.5
• Thread Size: M10x1
• Spanner Size: 24
• Nimetus: EP 1.800.141
• Tootja: EPS

Tootja: FAST

• Thread Size: M 12x1,5
• Colour: green
• Supplementary Article/Supplementary Info: with gasket/seal
• Number of pins: 2
• Tootja: DELLO AUTOMEGA

• Fabrication Number: ECT-CH-006
• Tootja: NTY

• Thread Size: M 10x1
• Housing Colour: black
• Tootja: FAE
• Lisainfo: FE12436

• Pressure [bar]: 5.5
• Housing Colour: blue
• Thread Size: M10×1-6g
• Diameter [mm]: 24
• Spanner Size: 24
• Number of pins: 1
• Tootja: DELPHI
• Nimetus: DE SW90015
• Kvaliteediklass: PJ

Lisainfo: "Tootja: DELPHI
(kvaliteediklass: PJ)"

• Fabrication Number: ECT-PL-007
• Tootja: NTY
• Nimetus: NTY ECT-PL-007

• Switch Pressure [bar]: 0.5
• Thread Size: M10x1.0
• Sensor Type: Closed-type Sensor
• Tootja: VERNET

• Pressure [bar]: 0.4
• Thread Size: M10 x 1
• Number of pins: 1
• Technical Information Number: circuit N.C.
• Tootja: ERA

• old version:
• Switch point from [bar]: 0.3
• Length [mm]: 51
• Switch point to [bar]: 0.55
• External Thread Size: M10 x 1
• Thread Length [mm]: 13
• Spanner Size: 24
• Number of connectors: 1
• Colour Coding: blue
• Weight [kg]: 0.04
• Supplementary Article/Info 2: with seal ring
• Tootja: BLUE PRINT

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Switch point from [bar]: 0.2
• Switch point to [bar]: 0.5
• External Thread Size: M14 x 1,5
• Spanner Size: 21
• Number of connectors: 1
• Colour: black
• Weight [kg]: 0.03
• Supplementary Article/Info 2: with seal ring
• Tootja: FEBI BILSTEIN
• Lisainfo: FE12228

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Length [mm]: 51
• Height [mm]: 54.3
• Thread Size: M10x1
• Spanner Size: 24
• Mounting Type: Bolted
• Supplementary Article/Supplementary Info: with gasket/seal
• Pressure from [bar]: 0.35
• Pressure to [bar]: 0.55
• Number of connectors: 1
• Combi Switch Function: Normally Closed Contact
• Connector Shape: round
• Corresponds to the original part in colour: blue
• Weight [kg]: 0.028
• Tootja: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Switch point from [bar]: 0.2
• Switch point to [bar]: 0.5
• External Thread Size: M14 x 1,5
• Spanner Size: 21
• Number of connectors: 1
• Colour: black
• Weight [kg]: 0.04
• Supplementary Article/Info 2: with seal ring
• Tootja: BLUEPRINT

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• old version:
• Length [mm]: 51
• Switch point from [bar]: 0.3
• Switch point to [bar]: 0.55
• Inner Diameter [mm]: 3.1
• External Thread Size: M10 x 1
• Thread Length [mm]: 13
• Spanner Size: 24
• Number of connectors: 1
• Colour Coding: blue
• Surface: Zinc-coated
• Weight [kg]: 0.027
• Supplementary Article/Info 2: with seal ring
• Tootja: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• old version:
• Switch point from [bar]: 0.3
• Length [mm]: 51
• Switch point to [bar]: 0.55
• Inner Diameter [mm]: 3.1
• External Thread Size: M10 x 1
• Thread Length [mm]: 13
• Spanner Size: 24
• Number of connectors: 1
• Colour Coding: blue
• Surface: Zinc-coated
• Weight [kg]: 0.027
• Supplementary Article/Info 2: with seal ring
• Nimetus: SW 40 91 7665
• Tootja: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Length [mm]: 61
• External Thread Size: M12 x 1,5
• Spanner Size: 19
• Number of connectors: 2
• Colour: grey
• Screw length below head [mm]: 28
• Weight [kg]: 0.023
• Supplementary Article/Info 2: with seal ring
• Tootja: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• new version:
• Switch point from [bar]: 0.3
• Switch point to [bar]: 0.55
• External Thread Size: M10 x 1
• Spanner Size: 22
• Number of connectors: 1
• Colour: blue
• Surface: Zinc-coated
• Weight [kg]: 0.03
• Supplementary Article/Info 2: with seal ring
• Tootja: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Sensor Type: NTC Sensor
• Mounting Type: Bolted
• Connector Shape: oval
• Number of pins: 2
• Spanner Size: 19
• Thread Size: M12x1.5
• for OE number: 46462179
• Supplementary Article/Info 2: with seal ring
• Tootja: NRF
• Lisainfo: 727005 NRF

• Thread Size: M12x1.5
• Spanner Size: 19
• Tootja: FAST

• Length [mm]: 61
• External Thread Size: M12 x 1,5
• Spanner Size: 19
• Number of connectors: 2
• Colour: grey
• Screw length below head [mm]: 28
• Weight [kg]: 0.03
• Supplementary Article/Info 2: with seal ring
• Nimetus: SW 40 92 8381
• Tootja: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Tightening torque to [Nm]: 20
• Voltage [V]: 12
• Pressure from [bar]: 0.4
• Thread Size: M10x1
• Spanner Size: 24
• Length [mm]: 51
• Colour Coding: black
• Nimetus: MM SAA103
• Tootja: MAGNETI MARELLI

• Number of pins: 2
• Socket colour: bright blue
• Connector Shape: oval
• Thread Size: M 12x1,5
• Spanner Size: 19 mm
• for OE number: 46469865
• Tootja: MEAT & DORIA

• for OE number: 12 38 938
• Length [mm]: 69
• Supplementary Article/Info 2: with seal ring
• Fabrication Number: ECP-PL-009
• Tootja: NTY

• new version:
• Switch point from [bar]: 0.3
• Switch point to [bar]: 0.55
• External Thread Size: M10 x 1
• Spanner Size: 22
• Number of connectors: 1
• Colour: blue
• Surface: Zinc-coated
• Weight [kg]: 0.03
• Supplementary Article/Info 2: with seal ring
• Nimetus: SW 40 92 7223
• Tootja: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Housing Colour: blue
• Number of pins: 2
• Thread Size: M12X1.5-6g
• Spanner Size: 19
• Nimetus: DE TS10253
• Tootja: DELPHI

• Number of pins: 2
• Housing Colour: green
• Weight [kg]: 0.03
• Tootja: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Sensor Type: Inductive Sensor
• Number of pins: 2
• Supplementary Article/Info 2: without cable
• Tootja: ABAKUS LORO

General Information: The following information is for general and informational purposes only and does not constitute warranty terms. Warranty terms and conditions are available from our dealers and in our general terms and conditions of sale. Abakus spare/repair parts are intended only for vehicle repairs in order to restore their original functionality. Abakus spare/repair parts are used or sold to users only for the purpose of repairing vehicles to restore their original look and functionality and are not original/genuine/OE/OEM/OES replacement parts. These items do not originate from the vehicle manufacturer and may be the subject of a design not owned by Abakus. They may only be used for repairs to restore the intended vehicle to its original appearance. Our products are delivered without instruction of installation. Installation of our product may only be carried out by trained specialist technicians in specific car repairs. Products supplied by us are exclusively intended for proper and appropriate use. The warranty may become invalid in the event of: improper installation or repair, unsuitable application or use, installation or repair made outside specialist car workshops. Warranty claims are lost if the vehicle is modified and used for motor sports, tuning or similar events (except our tuning parts which are described in TecDoc and on our price list). Warranty application should include complete documentation among others: chassis no., first registration, vehicle mileage, information about LPG installation, fault memory log, pictures, our QC (quality check) code, installation invoice, contact details of the car repair workshop performing the replacement or repair. Warranty application are available in our Client Panel system. Complaints may require supplementing data such as error memory logs. Incomplete documentation may result in rejection of the claim. Any damage caused during transport is not considered quality damage and will be considered on an individual basis. The product is intended for use within the performance limits specified by the manufacturer and should only be used by qualified personnel who have been trained to operate this product. Before each use, the product should be checked for damage or fixing of its parts and not used if any defects or loose parts are found. Failure to follow the manufacturer's guidelines could result in potential product damage or even injury. Wear appropriate protective clothing if necessary when working with the product.

• Mootorikood: 192 B3.000
• Thread Size: M12x1,5
• Spanner Size: 19
• Corresponds to the original part in colour: white, green, black
• for article number: 1.880.170, 1.880.190
• Nimetus: EP 1.830.239
• Tootja: EPS

• Mootorikood: 192 B3.000
• Thread Size: M12x1,5
• Spanner Size: 19
• Corresponds to the original part in colour: white, green, black
• for article number: 7.8170, 7.8190
• Tootja: FACET

• Length [mm]: 63
• External Thread Size: M12 x 1,5
• Spanner Size: 19
• Number of connectors: 2
• Colour: green
• Screw length below head [mm]: 27
• Weight [kg]: 0.025
• Supplementary Article/Info 2: with seal ring
• Tootja: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• for OE number: 55 190 791
• Length [mm]: 62
• Thread Size: M12 x 1,5
• Number of pins: 2
• Supplementary Article/Info 2: with seal ring
• Housing Colour: black
• Weight [kg]: 0.03
• Tootja: VEMO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Length [mm]: 69
• Number of connectors: 2
• Lisainfo: Sensor, crankshaft pulse

• Length [mm]: 63
• External Thread Size: M12 x 1,5
• Spanner Size: 19
• Number of connectors: 2
• Colour: green
• Screw length below head [mm]: 27
• Weight [kg]: 0.025
• Supplementary Article/Info 2: with seal ring
• Nimetus: SW 70 92 8378
• Tootja: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Weight [kg]: 0.032
• Tootja: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Height [mm]: 39
• Resistor [Ohm]: 2,300
• Number of connectors: 2
• Tootja: VERNET

• Number of pins: 3
• Connector Shape: rectangular
• Socket colour: black
• Supplementary Article/Info 2: with cable
• Tootja: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Number of pins: 2
• Sensor Type: Inductive Sensor
• Supplementary Article/Info 2: without cable
• Quality: OE EQUIVALENT
• for OE number: 01238938
• Tootja: MEAT&DORIA

• Fabrication Number: ECP-PL-041
• Number of pins: 3
• Tootja: NTY

• vajaminev tükihulk: 1
• Number of pins: 2
• Sensor Type: Inductive Sensor
• Supplementary Article/Info 2: with cable
• Housing Colour: black
• Tootja: BREMI

• Sensor Type: Hall Sensor
• Number of pins: 3
• Tootja: ABAKUS LORO

General Information: The following information is for general and informational purposes only and does not constitute warranty terms. Warranty terms and conditions are available from our dealers and in our general terms and conditions of sale. Abakus spare/repair parts are intended only for vehicle repairs in order to restore their original functionality. Abakus spare/repair parts are used or sold to users only for the purpose of repairing vehicles to restore their original look and functionality and are not original/genuine/OE/OEM/OES replacement parts. These items do not originate from the vehicle manufacturer and may be the subject of a design not owned by Abakus. They may only be used for repairs to restore the intended vehicle to its original appearance. Our products are delivered without instruction of installation. Installation of our product may only be carried out by trained specialist technicians in specific car repairs. Products supplied by us are exclusively intended for proper and appropriate use. The warranty may become invalid in the event of: improper installation or repair, unsuitable application or use, installation or repair made outside specialist car workshops. Warranty claims are lost if the vehicle is modified and used for motor sports, tuning or similar events (except our tuning parts which are described in TecDoc and on our price list). Warranty application should include complete documentation among others: chassis no., first registration, vehicle mileage, information about LPG installation, fault memory log, pictures, our QC (quality check) code, installation invoice, contact details of the car repair workshop performing the replacement or repair. Warranty application are available in our Client Panel system. Complaints may require supplementing data such as error memory logs. Incomplete documentation may result in rejection of the claim. Any damage caused during transport is not considered quality damage and will be considered on an individual basis. The product is intended for use within the performance limits specified by the manufacturer and should only be used by qualified personnel who have been trained to operate this product. Before each use, the product should be checked for damage or fixing of its parts and not used if any defects or loose parts are found. Failure to follow the manufacturer's guidelines could result in potential product damage or even injury. Wear appropriate protective clothing if necessary when working with the product.

• Cable Length [mm]: 590
• Number of pins: 3
• Tootja: DELPHI
• Nimetus: DE SS11092

• Spanner Size: 19 mm
• Sensor Type: NTC Sensor
• Number of pins: 2
• Connecting thread: M12 x 1,5
• Tootja: ERA

• Colour: black
• Cable Length [mm]: 650
• Alternatively:
• Number of pins: 3
• Fitting Depth [mm]: 34.5
• Weight [kg]: 0.074
• Operating Mode: Electric
• Alternative Repair Kit: 550067
• Resistor [kOhm]: 1.1
• Tootja: ERA

• Operating Mode: Electric
• Tootja: MAGNETI MARELLI

• Number of pins: 3
• Guarantee: 3 years guarantee
• Weight [kg]: 0.03
• Always compare old and new part (in particular OE No.):
• Tootja: SKV GERMANY
• Nimetus: CE 17SKV498

• Käigukasti liik: mitte sequentiellkäigukasti jaoks
• Mounting Type: Bayonet
• Voltage [V]: 12
• Number of pins: 2
• Operating Mode: Electric
• Combi Switch Function: Normally Closed Contact
• Assy./disassy. by qualified personnel required!:
• Tootja: HELLA
• Nimetus: HE 6DD179465101

• Colour: black
• Alternatively:
• Number of pins: 2
• Fitting Depth [mm]: 39
• Weight [kg]: 0.03
• Alternative Repair Kit: 550052
• Resistor [kOhm]: 2.4
• Tootja: ERA

• Sensor Type: Inductive Sensor
• Number of pins: 2
• Connector Shape: oval
• Supplementary Article/Info 2: without cable
• Weight [kg]: 0.05
• Nimetus: VA 366177
• Tootja: VALEO

• Length [mm]: 69
• Number of connectors: 2
• Weight [kg]: 0.03
• Supplementary Article/Info 2: with seal ring
• Tootja: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Mootorikood: 192 B3.000
• Nimetus: EP 1.953.288
• Tootja: EPS

• Mootorikood: 192 B3.000
• Tootja: FACET

• Sensor Type: Inductive Sensor
• Number of pins: 3
• Voltage [V]: 12
• Connector Shape: angled
• Supplementary Article/Info 2: with cable
• Resistor [Ohm]: 1,350
• Weight [kg]: 0.1
• Tootja: VALEO
• Nimetus: VA 254029

• Number of pins: 3
• Fitting Depth [mm]: 8.3
• Resistor [kOhm]: 13.4
• Tootja: ERA

• vajaminev tükihulk: 1
• Voltage [V]: 12
• Number of pins: 3
• Sensor Type: Hall Sensor
• Supplementary Article/Info 2: without cable
• Housing Colour: black
• Tootja: BREMI

• Resistor [Ohm]: 2,700
• Number of pins: 2
• Sensor Type: Inductive Sensor, Passive sensor
• Number of connectors: 2
• Connector Shape: oval
• Supplementary Article/Info 2: with seal ring, for crankshaft, without cable
• Required quantity: 1
• Operating Mode: Electric
• Socket colour: black
• Supplementary Article/Supplementary Info: with gasket/seal
• Rated Voltage [V]: 12
• Fitting Depth [mm]: 39.3
• Number of mounting bores: 1
• Weight [kg]: 0.044
• Tootja: VEMO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Number of pins: 2
• Tootja: FAE

• Mootorikood: 192 B3.000
• Length [mm]: 400
• Alternatively:
• Number of pins: 3
• Housing Colour: white
• Weight [kg]: 0.048
• Alternative Repair Kit: 550094
• Resistor M[ohm]: 1.8
• Tootja: ERA

• Height [mm]: 8.3
• Sensor Type: Hall Sensor
• Number of connectors: 3
• Tootja: VERNET

• Number of connectors: 3
• Cable Length [mm]: 660
• Weight [kg]: 0.07
• Tootja: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Length [mm]: 69
• Number of connectors: 2
• Weight [kg]: 0.03
• Supplementary Article/Info 2: with seal ring
• Nimetus: SW 40 92 2374
• Tootja: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

Tootja: MAGNETI MARELLI

• Number of connectors: 2
• Weight [kg]: 0.04
• for OE number: 55190562
• Tootja: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Oxygen Sensor: Diagnostic Probe, Thread pre-greased
• Fabrication Number: ESL-SK-000
• Tootja: NTY
• Nimetus: NTY ESL-SK-000

• Number of mounting bores: 1
• Voltage [V]: 12
• Resistor [Ohm]: 2,700
• Sensor Type: Inductive Sensor
• Supplementary Article/Supplementary Info: with gasket/seal
• Number of pins: 2
• Supplementary Article/Info 2: without cable
• Assy./disassy. by qualified personnel required!:
• SVHC: 7439-92-1; Lead
• Tootja: HELLA

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Colour: black
• Number of pins: 2
• Fitting Depth [mm]: 39
• Weight [kg]: 0.03
• Resistor [kOhm]: 2.4
• Tootja: ERA

• Number of pins: 2
• Tootja: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Number of pins: 2
• Tootja: DELPHI
• Nimetus: DE AS10170

• Sensor Type: Hall Sensor
• Number of pins: 3
• Voltage [V]: 12
• Connector Shape: oval
• Supplementary Article/Info 2: without cable
• Weight [kg]: 0.03
• Nimetus: VA 253818
• Tootja: VALEO

• Sensor Type: Hall Sensor
• Number of pins: 3
• Connector Shape: angled
• Supplementary Article/Info 2: with cable
• Weight [kg]: 0.06
• Tootja: VALEO

• Lambda andur: Diagnoosisond
• Installatsiooni pool: pärast katalüsaatorit
• Plokieraldus:
• Mootorikood: 192 B3.000
• Cable Length [mm]: 340
• Oxygen Sensor: Planar probe, Heated
• Tootja: DELPHI
• Nimetus: DE ES10792-12B1

• Lambda andur: Sond
• Mootorikood: 192 B3.000
• Cable Length [mm]: 432
• Oxygen Sensor: Planar probe, Heated
• Nimetus: DE ES10798-12B1
• Tootja: DELPHI

• Number of pins: 3
• Tootja: FAE

• Lambda andur: Diagnoosisond
• Oxygen Sensor: Unheated
• Number of pins: 4
• Cable Length [mm]: 520
• Quality: OE EQUIVALENT
• for OE number: 025198484
• Tootja: MEAT&DORIA

• Mootorikood: 192 B3.000
• Nimetus: EP 1.953.449
• Tootja: EPS

• Lambda andur: Diagnoosisond
• Oxygen Sensor: Heated
• External Thread Size: M18 x 1,5
• Spanner Size: 22
• Number of circuits: 4
• Cable Length [mm]: 650
• Weight [kg]: 0.096
• Nimetus: SW 33 10 3162
• Tootja: SWAG

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Mootorikood: 192 B3.000
• Tootja: FACET

• Number of pins: 4
• Oxygen Sensor: Planar probe
• Voltage [V]: 12
• Overall Length [mm]: 500
• Tootja: AIC

General Information: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Voltage [V]: 12
• Sensor Type: Hall Sensor
• Number of pins: 3
• Assy./disassy. by qualified personnel required!:
• SVHC: 7439-92-1; Lead
• Tootja: HELLA
• Nimetus: HE 6PU009121791

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• Installatsiooni pool: pärast katalüsaatorit
• Line insulation design: with silicone-coated woven-fibre insulation
• Oxygen Sensor: Planar probe, Heated, Thread pre-greased
• Cable Length [mm]: 210
• Number of circuits: 4
• Weight [kg]: 0.09
• Tootja: VEMO GERMANY

Supplementary Article/Supplementary Info: with squeeze connector, with shrink squeeze connector General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Lambda andur: Sond
• Väljalaskesüsteem: eelkatalüsaatori jaoks
• Quality: OE
• Manufacturer Restriction: DENSO
• Thread Size: M18x1.5
• Cable Length [mm]: 750
• Number of pins: 4
• Weight [g]: 93
• Gross Weight [g]: 140
• Tootja: DENSO
• Nimetus: DN DOX-0150
• Kvaliteediklass: Q