• Installatsiooni pool: stirnseitig
• Inner Diameter [mm]: 35
• Outer Diameter [mm]: 48
• Width [mm]: 10
• Material: FPM (fluoride rubber)
• Tootja: JP GROUP A/S
• Lisainfo: Oil seal, 35x48x10 mm

• Fitting Position: transmission sided
• Inner Diameter [mm]: 85
• Outer Diameter [mm]: 105
• Thickness [mm]: 11
• Material: FPM (fluoride rubber)/ACM (polyacrylate rubber)
• Lisainfo: Oil seal for crankshaft, 85x105x11 mm

• Fitting Position: transmission sided
• Inner Diameter [mm]: 85
• Outer Diameter [mm]: 105
• Width 1 [mm]: 9
• Width 2 [mm]: 11
• Housing Type: with housing
• Lisainfo: Seal flange for crankshaft

• Installatsiooni pool: stirnseitig
• Kaal (kg): 0,016
• Siseläbimõõt [mm]: 35
• Välisläbimõõt [mm]: 48
• Materjal: ACM((Polyacryl-Kautschuk)
• vajaminev tükihulk: 1
• Jämedus/Tugevus (mm): 10
• Üldine informatsioon: seal ring;35*48*10 mm
• Tootja: VIKA

• Installatsiooni pool: stirnseitig
• Üldine informatsioon: seal ring
• Tootja: VIKA

• Kogus pakendis: 10
• Installatsiooni pool: stirnseitig
• Tootja: AIC

Üldine informatsioon: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Mootorikood: NG
• Fitting Position: Front
• Height 1 [mm]: 10
• Outer Diameter 1 [mm]: 47
• Inner Diameter 1 [mm]: 32
• Material: FPM (fluoride rubber)
• for OE number: 026103085D
• Swirl Type: Alternating Twist
• Dust Cover: with dust lip
• Nimetus: VOLLI RONGASTIHEND, NUKKVOLL
• Tootja: COT
• Lisainfo: 12012709

• Fitting Position: frontal sided
• Inner Diameter [mm]: 35
• Outer Diameter [mm]: 48
• Height [mm]: 10
• Swirl Type: Right-hand Twist
• Radial Shaft Seal Design: ASW
• Tootja: DR MOTOR PRZEWODY PRZELEWOWE

• Fitting Position: Front
• Inner Diameter [mm]: 35
• Outer Diameter [mm]: 48
• Height [mm]: 10
• Fabrication Number: NUP-VW-012
• Tootja: NTY

• Installatsiooni pool: stirnseitig
• vajaminev tükihulk: 1
• Inner Diameter [mm]: 32
• Outer Diameter [mm]: 47
• Width [mm]: 10
• SVHC: No SVHC present!
• Tootja: INA

• Thickness [mm]: 10
• Inner Diameter [mm]: 35
• Outer Diameter [mm]: 48
• Material: ACM (Polyacrylate)
• Fitting Position: frontal sided
• Weight [kg]: 0.016
• Tootja: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Installatsiooni pool: stirnseitig
• Mootorikood: NG
• Material: FPM (fluoride rubber)
• Inner Diameter [mm]: 32
• Outer Diameter [mm]: 47
• Height [mm]: 10
• Radial Shaft Seal Design: A SL
• Swirl Type: Alternating Twist
• Nimetus: VOLLI RONGASTIHEND, NUKKVOLL
• Tootja: REI
• Lisainfo: 81-19299-10

• Installatsiooni pool: stirnseitig
• Inner Diameter [mm]: 32
• Outer Diameter [mm]: 47
• Height [mm]: 10
• Radial Shaft Seal Design: ASW
• Swirl Type: Alternating Twist
• Material: FPM (fluoride rubber)/ACM (polyacrylate rubber)
• Dust Cover: with dust lip
• Alternative Repair Kit: 325.156
• Tootja: ELRING
• Lisainfo: 325.155 ELR

• Mootorikood: NG
• Fitting Position: frontal sided
• Height [mm]: 10
• Material: ACM (Polyacrylate)
• Inner Diameter [mm]: 35
• Outer Diameter [mm]: 48
• Tootja: BGA

• Installatsiooni pool: stirnseitig
• Fitting Position: transmission sided
• Height [mm]: 11
• Material: FPM (fluoride rubber)
• Inner Diameter [mm]: 85
• Outer Diameter [mm]: 105
• Swirl Type: Left-hand Twist
• Dust Cover: with dust lip
• Tootja: DELLO AUTOMEGA

• Thickness [mm]: 10
• for OE number: 068 103 085 E
• Fitting Position: frontal sided
• Inner Diameter [mm]: 32
• Outer Diameter [mm]: 47
• Weight [kg]: 0.023
• Tootja: VAICO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Mootorikood: NG
• Plokieraldus:
• Installatsiooni pool: stirnseitig
• Inner Diameter [mm]: 32
• Outer Diameter [mm]: 47
• Height [mm]: 10
• Swirl Type: Alternating Twist
• Nimetus: VOLLI RONGASTIHEND, NUKKVOLL
• Tootja: AJU

• Fitting Position: frontal sided, Front
• Height 1 [mm]: 7
• Outer Diameter 1 [mm]: 35
• Inner Diameter 1 [mm]: 23
• Material: FPM (fluoride rubber)
• Swirl Type: Right-hand Twist
• Dust Cover: with dust lip
• Nimetus: VOLLI RONGASTIHEND, KŽIGUKAST
• Tootja: COT

• Installatsiooni pool: stirnseitig
• Inner Diameter [mm]: 32
• Outer Diameter [mm]: 47
• Height [mm]: 10
• Radial Shaft Seal Design: ASW
• Swirl Type: Alternating Twist
• Material: FPM (fluoride rubber)
• Dust Cover: with dust lip
• Alternative Repair Kit: 325.155
• Tootja: ELRING

• Installatsiooni pool: stirnseitig
• Inner Diameter [mm]: 35
• Outer Diameter [mm]: 48
• Height [mm]: 10
• Radial Shaft Seal Design: ASW
• Swirl Type: Right-hand Twist
• Material: FPM (fluoride rubber)
• Dust Cover: with dust lip
• Tootja: ELRING

• Installatsiooni pool: stirnseitig
• Mootorikood: NG
• Material: FPM (fluoride rubber)
• Inner Diameter [mm]: 35
• Outer Diameter [mm]: 48
• Height [mm]: 10
• Radial Shaft Seal Design: A SL
• Swirl Type: Right-hand Twist
• Nimetus: VOLLI RONGASTIHEND, VŽNTVOLL
• Tootja: REI

• Mootorikood: NG
• Fitting Position: frontal sided
• Height 1 [mm]: 10
• Outer Diameter 1 [mm]: 48
• Inner Diameter 1 [mm]: 35
• Material: FPM (fluoride rubber)
• for OE number: 034115137A
• Swirl Type: Right-hand Twist
• Dust Cover: with dust lip
• Nimetus: VOLLI RONGASTIHEND, OLIPUMP
• Tootja: COT

• Inner Diameter [mm]: 35
• Thickness [mm]: 10
• Outer Diameter [mm]: 48
• Fitting Position: frontal sided
• for OE number: 054 115 147 B
• Weight [kg]: 0.02
• Material: FPM (fluoride rubber)
• Tootja: VAICO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Installatsiooni pool: stirnseitig
• Inner Diameter [mm]: 35
• Outer Diameter [mm]: 48
• Height [mm]: 10
• Radial Shaft Seal Design: ASW
• Swirl Type: Right-hand Twist
• Material: FPM (fluoride rubber)/ACM (polyacrylate rubber)
• Dust Cover: with dust lip
• Tootja: ELRING

• Mootorikood: NG
• Fitting Position: transmission sided
• Height [mm]: 12
• Material: NBR (nitrile butadiene rubber)
• Inner Diameter [mm]: 85
• Outer Diameter [mm]: 105
• Tootja: BGA

• Fitting Position: transmission sided
• Inner Diameter [mm]: 85
• Outer Diameter [mm]: 105
• Width [mm]: 11
• Nimetus: Volli rongastihend, V„ntvoll
• Tootja: DRM

• Installatsiooni pool: kastipoolselt
• Mootorikood: NG
• Kogus pakendis: 10
• Fitting Position: frontal sided
• Weight [kg]: 0.035
• Tootja: VAICO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Fitting Position: frontal sided
• General Information: shaft oil seal
• Tootja: BORSEHUNG

• Thickness [mm]: 11
• Inner Diameter [mm]: 85
• Outer Diameter [mm]: 105
• Material: FPM (fluoride rubber)
• Fitting Position: transmission sided
• Weight [kg]: 0.058
• Tootja: FEBI BILSTEIN

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Fitting Position: Axle beam
• General Information: shaft oil seal
• Tootja: BORSEHUNG

• Installatsiooni pool: kastipoolselt
• Inner Diameter [mm]: 85
• Outer Diameter [mm]: 105
• Height [mm]: 11
• Radial Shaft Seal Design: ASW
• Swirl Type: Left-hand Twist
• Material: FPM (fluoride rubber)
• Dust Cover: with dust lip
• Alternative Repair Kit: 829.056
• Tootja: ELRING
• Lisainfo: 342.093 ELR

• Installatsiooni pool: kastipoolselt
• Mootorikood: NG
• Material: FPM (fluoride rubber)
• Inner Diameter [mm]: 85
• Outer Diameter [mm]: 105
• Height [mm]: 11
• Radial Shaft Seal Design: A SL
• Swirl Type: Left-hand Twist
• Height 1 [mm]: 9
• Nimetus: VOLLI RONGASTIHEND, VŽNTVOLL
• Tootja: REI
• Lisainfo: 81-23708-40

• Installatsiooni pool: stirnseitig
• Mootorikood: NG
• Inner Diameter [mm]: 35
• Outer Diameter [mm]: 48
• Height [mm]: 10
• Swirl Type: Right-hand Twist
• Nimetus: VOLLI RONGASTIHEND, VŽNTVOLL
• Tootja: AJU

• Kogus pakendis: 5
• Thickness [mm]: 11
• Inner Diameter [mm]: 85
• Outer Diameter [mm]: 105
• Fitting Position: transmission sided
• Weight [kg]: 0.103
• Tootja: VAICO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Fitting Position: transmission sided
• Height 1 [mm]: 12
• Outer Diameter 1 [mm]: 105
• Inner Diameter 1 [mm]: 85
• Material: FPM (fluoride rubber)
• Swirl Type: Left-hand Twist
• Dust Cover: with dust lip
• Nimetus: VOLLI RONGASTIHEND, VŽNTVOLL
• Tootja: COT

• Installatsiooni pool: kastipoolselt
• Supplementary Article/Info 2: with flange
• Outer Diameter [mm]: 111
• Inner Diameter [mm]: 85
• Height [mm]: 16
• Tootja: DELLO AUTOMEGA

• Supplementary Article/Info 2: with flange
• Fitting Position: transmission sided
• Fabrication Number: NUP-VW-006
• Tootja: NTY

• Kogus pakendis: 5
• Installatsiooni pool: kastipoolselt
• Tootja: AIC

Üldine informatsioon: Our products are usually delivered without installation instructions. Installation may only be carried out by trained specialist technicians. Products supplied by us are exclusively intended for proper and appropriate use. The warranty is void in the event of improper, contrary to the intended purpose or unsuitable application or use. For electronic items that leave fault memory entries, it is essential to submit fault memory logs in the event of a claim. This consequently concerns all electronic items that are detected, monitored and controlled by the engine control unit, such as sensors of all kinds (e.g. NOX sensors, ABS sensors), mass airflow sensors, airbag slip rings, headlamp levelling control units, throttle valves, lambda sensors or EGR modules. If you encounter difficulties during a repair (troubleshooting max. 1 hr.), please contact technical support at: Phone: 040 - 25 30 66 55 Email: service@aic-germany.de This often avoids extensive troubleshooting that is disproportionate to normal repair times. The following applies to complaints: The more complete the processes are submitted, the faster they can be processed. Complete documentation includes the warranty application (incl. KBA no., chassis no., first registration, engine code, mileage), first and second installation invoice, fault memory log, guided troubleshooting and, if applicable, pictures. Incomplete documentation may result in rejection of the claim.

• Fitting Position: transmission sided
• Height 1 [mm]: 11
• Outer Diameter 1 [mm]: 104
• Inner Diameter 1 [mm]: 84
• Material: MVQ (silicone rubber)
• Swirl Type: Left-hand Twist
• Dust Cover: with dust lip
• Tootja: CORTECO

• Installatsiooni pool: kastipoolselt
• Inner Diameter [mm]: 85
• Outer Diameter [mm]: 105
• Height [mm]: 11
• Radial Shaft Seal Design: ASW
• Swirl Type: Left-hand Twist
• Material: FPM (fluoride rubber)
• Dust Cover: with dust lip
• Supplementary Article/Info 2: with mounting sleeve
• Tootja: ELRING

• Mootorikood: NG
• Fitting Position: Pulley side
• Nimetus: Volli rongastihendikomplekt, Mootor
• Tootja: COT

• Installatsiooni pool: kastipoolselt
• Kaal (kg): 0,17
• Siseläbimõõt [mm]: 85
• vajaminev tükihulk: 1
• Piirangutega toode/piirangu info 2: koos flantsiga
• Üldine informatsioon: sealing flang; rear
• Tootja: VIKA

• Mootorikood: NG
• Kogus pakendis: 5
• Fitting Position: transmission sided
• Inner Diameter [mm]: 85
• Weight [kg]: 0.265
• Tootja: VAICO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Fitting Position: transmission sided
• Inner Diameter [mm]: 85
• Radial Shaft Seal Design: SP
• Housing Type: with housing
• Nimetus: Volli rongastihend, V„ntvoll
• Tootja: DRM

• Mootorikood: NG
• Fitting Position: transmission sided
• Supplementary Article/Info 2: with mounting sleeve
• Height 1 [mm]: 11
• Outer Diameter 1 [mm]: 105
• Inner Diameter 1 [mm]: 85
• Material: FPM (fluoride rubber)
• for OE number: 068103071F
• Swirl Type: Alternating Twist
• Tootja: CORTECO

• Outer Diameter [mm]: 47
• Thickness [mm]: 10
• Inner Diameter [mm]: 32
• Fitting Position: transmission sided
• Weight [kg]: 0.195
• Tootja: VAICO

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Mootorikood: NG
• Fitting Position: transmission sided
• Supplementary Article/Info 2: with mounting sleeve
• Height 1 [mm]: 15.7
• Outer Diameter 1 [mm]: 131
• Outer Diameter 2 [mm]: 152
• Inner Diameter 1 [mm]: 85
• Material: PTFE (polytetrafluoroethylene)
• for OE number: 028103171B
• Swirl Type: Alternating Twist
• Nimetus: VOLLI RONGASTIHEND, VŽNTVOLL
• Tootja: COT

• Installatsiooni pool: kastipoolselt
• Kaal (kg): 0,17
• Siseläbimõõt [mm]: 85
• vajaminev tükihulk: 1
• Piirangutega toode/piirangu info 2: koos flantsiga
• Üldine informatsioon: sealing flang; rear
• Tootja: VIKA

• Installatsiooni pool: kastipoolselt
• Inner Diameter [mm]: 85
• Radial Shaft Seal Design: SP
• Swirl Type: Left-hand Twist
• Housing Type: with housing
• Supplementary Article/Info 2: with mounting sleeve
• Tootja: ELRING
• Lisainfo: 804.850 ELR

Material: PTFE (polytetrafluoroethylene)/ACM (polyacrylate rubber) Installation Information: Mounting dry and without any additional oil and grease