Tootekategooriad
Filtrid Pidurid vedrustus/alusvanker Roolisüsteem Jahutus/kliima Elektrisüsteem Veokonks/lisad Jõuülekanne Väljalaskesüsteem Kere Süüte-/eelsüütesüsteem Mootor Klaasid/klaasipuhastus Valgustus Kütus Kabiinivarustus HooldusToode
Kirjeldus
Laoseis
Hind
(km-ga)
- Inner Diameter [mm]: 35
- Outer Diameter [mm]: 48
- Height [mm]: 7
- Fitting Position: frontal sided
- Dust Cover: with dust lip
-
Swirl Type: Right-
hand Twist -
Material: MVQ
(silicone rubber) - Tootja: TOPRAN
General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.
- Installatsiooni pool: kastipoolselt
- Inner Diameter [mm]: 55
- Outer Diameter [mm]: 70
- Width [mm]: 8
- Radial Shaft Seal Design: ASW
-
Swirl Type: Left-
hand Twist -
Material: FPM
(fluoride rubber)/ ACM (polyacrylate rubber) - Dust Cover: with dust lip
- Tootja: JP GROUP
-
Lisainfo: Oil seal for camshaft,
rear
- Installatsiooni pool: stirnseitig
- vajaminev tükihulk: 1
- Fitting Position: Cylinder Head
- Inner Diameter [mm]: 35
- Outer Diameter [mm]: 48
- Height [mm]: 7
- Weight [kg]: 0.015
- Tootja: VAICO
General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.
- Installatsiooni pool: stirnseitig
- Inner Diameter [mm]: 35
- Outer Diameter [mm]: 48
- Height [mm]: 7
-
Radial Shaft Seal Design: AW/
BS -
Swirl Type: Right-
hand Twist -
Material: MVQ
(silicone rubber) - Dust Cover: with dust lip
- Tootja: ELRING
- Installatsiooni pool: stirnseitig
-
Swirl Type: Right-
hand Twist - Height [mm]: 7
- Inner Diameter [mm]: 35
- Outer Diameter [mm]: 48
- Tootja: OYODO
- Installatsiooni pool: stirnseitig
- Mootorikood: C 18 NT
-
Material: MVQ
(silicone rubber) - Inner Diameter [mm]: 35
- Outer Diameter [mm]: 48
- Height [mm]: 7
- Radial Shaft Seal Design: A SL
-
Swirl Type: Right-
hand Twist -
Nimetus: VOLLI RONGASTIHEND,
NUKKVOLL - Tootja: REI
- Mootorikood: C 18 NT
- Fitting Position: frontal sided
- Height 1 [mm]: 7
- Outer Diameter 1 [mm]: 48
- Inner Diameter 1 [mm]: 35
-
Material: FPM
(fluoride rubber) - for OE number: 55352607
-
Swirl Type: Right-
hand Twist - Dust Cover: with dust lip
-
Nimetus: VOLLI RONGASTIHEND,
KIGUKAST - Tootja: COT
- Installatsiooni pool: stirnseitig
- Inner Diameter [mm]: 35
- Outer Diameter [mm]: 48
- Height [mm]: 7
-
Nimetus: VOLLI RONGASTIHEND,
NUKKVOLL - Tootja: AJU
- Lisainfo: AJU15012600
- Mootorikood: C 18 NT
- Fitting Position: Cylinder Head
- Weight [kg]: 0.016
- Tootja: VAICO
General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.
- Fitting Position: Front
- Height [mm]: 8
-
Material: NBR
(nitrile butadiene rubber) - Inner Diameter [mm]: 55
- Outer Diameter [mm]: 70
- Tootja: BGA
- Installatsiooni pool: kastipoolselt
- Inner Diameter [mm]: 55
- Outer Diameter [mm]: 70
- Height [mm]: 8
- Radial Shaft Seal Design: ASW
-
Swirl Type: Left-
hand Twist -
Material: FPM
(fluoride rubber)/ ACM (polyacrylate rubber) - Dust Cover: with dust lip
- Tootja: ELRING
- Fitting Position: Engine
- Height 1 [mm]: 8
- Outer Diameter 1 [mm]: 70.1
- Inner Diameter 1 [mm]: 55
-
Material: FPM
(fluoride rubber) -
Swirl Type: Left-
hand Twist - Tootja: CORTECO
- Nimetus: CO 12015548
Laki Auto universaaltooted
TecDoc sõidukite kataloog
TecDoc veokite kataloog