• Length [mm]: 300
• Fitting Position: Front, after catalytic converter
• Lambda Sensor: Diagnostic Probe, Thread pre-greased
• Fabrication Number: ESL-PL-008
• Manufacturer: NTY

• Number of circuits: 4
• Lambda Sensor: Regulating Probe
• Manufacturer: KAMOKA

• Lambda Sensor: Diagnostic Probe, Thread pre-greased
• Fabrication Number: ESL-SK-000
• Manufacturer: NTY
• Name: NTY ESL-SK-000

• for OE number: 855528, 9193654
• Lambda Sensor: Regulating Probe, Heated
• Fitting Position: before catalytic converter
• Cable Length [mm]: 575
• Number of pins: 4
• Number of circuits: 4
• Thread Size: M 18x1,5
• Connector Shape: oval
• Manufacturer: DELLO AUTOMEGA

• Lambda Sensor: Diagnostic Probe
• Manufacturer: JP GROUP
• Lisainfo: Lambda sensor
• Additional information: Lambda sensor

• Construction Year to: 12.2011
• Fitting Position: after catalytic converter
• Lambda Sensor: Diagnostic Probe
• Manufacturer: DELLO AUTOMEGA

• Lambda Sensor: Diagnostic Probe, Planar probe
• Fitting Position: after catalytic converter
• Number of pins: 4
• Manufacturer: TOPRAN

General Information: Any and all spare parts we supply are solely intended for the designated purpose as defined by us. Installation by trained personnel only. Our products are usually supplied without assembly instructions. Installation in vehicles other than those specified by us may lead to the exclusion of warranty.

• Lambda Sensor: Lambda Sensor
• Voltage [V]: 12
• Number of circuits: 4
• Weight [kg]: 0.09
• Resistor [Ohm]: 9
• Operating Mode: Electric
• Warranty: 3 years warranty
• Manufacturer: SKV GERMANY
• Name: CE 09SKV909

• Transmission Type: Manual Transmission
• Fitting Position: after catalytic converter
• Line insulation design: with silicone-coated woven-fibre insulation
• Length [mm]: 450
• Number of connectors: 4
• Version: Planar
• Weight [kg]: 0.105
• Manufacturer: VEMO GERMANY

Lambda Sensor: Diagnostic Probe, Regulating Probe, Thread pre-greased General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Construction Year to: 12.2011
• Lambda Sensor: Diagnostic Probe
• Fitting Position: after catalytic converter
• Number of circuits: 4
• Overall Length [mm]: 300
• Name: LAMBDA ANDUR
• Manufacturer: MAX

• Construction Year to: 12.2011
• Lambda Sensor: Regulating Probe, Diagnostic Probe, Finger probe
• Block Separation:
• Number of circuits: 4
• Connector/Clamp: Connector may need adjustment
• Transmission Type: Manual Transmission
• Name: LAMBDA ANDUR
• Manufacturer: MAX

Fitting Position: before catalytic converter, after catalytic converter

• Lambda Sensor: Diagnostic Probe, Lambda Sensor
• Engine Code: Z 12 XEP
• Voltage [V]: 12
• Length [mm]: 290
• Number of circuits: 4
• Weight [kg]: 0.09
• Operating Mode: Electric
• Warranty: 3 years warranty
• Manufacturer: SKV GERMANY
• Name: CE 09SKV073

• Transmission Type: Manual Transmission
• Lambda Sensor: Diagnostic Probe, Thread pre-greased
• Fitting Position: after catalytic converter
• Line insulation design: with silicone-coated woven-fibre insulation
• Number of pins: 4
• Socket colour: black
• Connector Shape: oval
• Thread Size: M18 x 1,5
• Weight [kg]: 0.085
• Length [mm]: 520
• for OE number: 08 55 386
• Cable Length [mm]: 210
• Number of circuits: 4
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Vehicle Identification Number (VIN) from: 6G000001
• Fitting Position: Front, Upper
• Exhaust System: before catalytic converter
• Lambda Sensor: Regulating Probe
• Length [mm]: 400
• Number of connectors: 4
• Manufacturer: VERNET

• Fitting Position: before catalytic converter
• Lambda Sensor: Regulating Probe, Heated
• External Thread Size: M18 x 1,5
• Spanner Size: 22
• Number of circuits: 4
• Cable Length [mm]: 220
• Weight [kg]: 0.067
• Manufacturer: FEBI

General Information: These products are designed to be used as originally intended and not modified for purpose. Please ensure the products are installed by a competent individual. N.B. products are usually supplied without fitting instructions.

• Lambda Sensor: Regulating Probe, Unheated
• Fitting Position: Exhaust Manifold
• Number of pins: 4
• Cable Length [mm]: 520
• Quality: OE EQUIVALENT
• Manufacturer: MEAT&DORIA

• Lambda Sensor: Diagnostic Probe, Planar probe, Heated
• Fitting Position: after catalytic converter
• Cable Length [mm]: 520
• Name: LAMBDA ANDUR
• Manufacturer: DLP
• Quality class: PJ

Additional information: "Tootja: DELPHI
ASTRA F CLASSIC KOMB
(kvaliteediklass: PJ)" Lisainfo: "Tootja: DELPHI
ASTRA F CLASSIC KOMB
(kvaliteediklass: PJ)"

• Resistor [Ohm]: 9
• Length [mm]: 275
• Number of circuits: 4
• Conductor Number: 4
• Cable Length [mm]: 275
• Lambda Sensor: Heated
• Name: LAMBDA ANDUR
• Manufacturer: MAG

• Lambda Sensor: Regulating Probe
• Voltage [V]: 12
• Length [mm]: 325
• Number of circuits: 4
• Weight [kg]: 0.13
• Resistor [Ohm]: 9
• Operating Mode: Electric
• Warranty: 3 years warranty
• Manufacturer: SKV GERMANY
• Name: CE 09SKV680

• Lambda Sensor: Lambda Sensor
• Cable Length [mm]: 290
• Alternatively:
• Number of circuits: 4
• Alternative Repair Kit: 570112
• Manufacturer: ERA

• Conductor Number: 4
• Resistor [Ohm]: 9
• Length [mm]: 575
• Number of circuits: 4
• Cable Length [mm]: 575
• Lambda Sensor: Heated
• Manufacturer: MAGNETI MARELLI

• Fitting Position: Front, Upper, before catalytic converter
• Vehicle Identification Number (VIN) to: 56999999
• Block Separation:
• Cable Length [mm]: 300
• Manufacturer: DELPHI
• Name: DE ES20315-12B1

Lambda Sensor: Regulating Probe, Diagnostic Probe, Planar probe, Heated Additional information: "Tootja: DELPHI
VECTRA C GTS, 08.02-
(kvaliteediklass: PJ)" Lisainfo: "Tootja: DELPHI
VECTRA C GTS, 08.02-
(kvaliteediklass: PJ)"

• Engine Code: Z 12 XEP
• Line insulation design: with silicone-coated woven-fibre insulation
• Number of pins: 4
• for OE number: V99760001
• Cable Length [mm]: 210
• Number of circuits: 4
• Weight [kg]: 0.09
• Length [mm]: 350
• Exhaust System: after catalytic converter
• Manufacturer: VEMO GERMANY

Lambda Sensor: Diagnostic Probe, Finger probe, Heated, Thread pre-greased Supplementary Article/Supplementary Info: with squeeze connector, with shrink squeeze connector General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Lambda Sensor: Regulating Probe, Thread pre-greased
• Fitting Position: Exhaust Manifold
• Line insulation design: with silicone-coated woven-fibre insulation
• Overall Length [mm]: 448
• Weight [kg]: 0.11
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Line insulation design: with silicone-coated woven-fibre insulation
• Lambda Sensor: Planar probe, Heated, Thread pre-greased
• Cable Length [mm]: 210
• Number of circuits: 4
• Weight [kg]: 0.09
• Manufacturer: VEMO GERMANY

Fitting Position: before catalytic converter, after catalytic converter Supplementary Article/Supplementary Info: with squeeze connector, with shrink squeeze connector General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Construction Year to: 12.2011
• Lambda Sensor: Regulating Probe, Diagnostic Probe
• Block Separation:
• Number of circuits: 4
• Recommended change interval [km]: 160,000
• Connector/Clamp: Connector may need adjustment
• Name: LAMBDA ANDUR
• Manufacturer: BOS

Fitting Position: before catalytic converter, after catalytic converter

• Exhaust System: for pre-catalytic converter
• Quality: OE
• Manufacturer Restriction: DENSO
• Thread Size: M18x1.5
• Cable Length [mm]: 750
• Number of pins: 4
• Weight [g]: 93
• Gross Weight [g]: 140
• Manufacturer: DENSO
• Name: DN DOX-0150
• Quality class: Q

Lambda Sensor: Regulating Probe, Heated, Planar probe, Thread pre-greased, Lambda Sensor Additional information: "Tootja: DENSO
(kvaliteediklass: Q)" Lisainfo: "Tootja: DENSO
(kvaliteediklass: Q)"

• Engine Code: Z 12 XEP
• Fitting Position: after catalytic converter
• Quantity: 1
• Lambda Sensor: Diagnostic Probe, Planar probe, Thread pre-greased
• Line insulation design: with silicone-coated woven-fibre insulation
• Length [mm]: 350
• Thread Size: M18x1,5mm
• Resistor [Ohm]: 9
• Overall Length [mm]: 300
• Cable Length [mm]: 300
• Number of pins: 4
• Weight [kg]: 0.12
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Construction Year to: 12.2011
• Lambda Sensor: Diagnostic Probe
• Fitting Position: after catalytic converter
• Number of circuits: 4
• Overall Length [mm]: 300
• Available as universal article as well, see article no.: 0258986602
• Recommended change interval [km]: 250,000
• Name: LAMBDA ANDUR
• Manufacturer: BOS

• Construction Year to: 12.2011
• Lambda Sensor: Regulating Probe
• Fitting Position: before catalytic converter
• Number of circuits: 4
• Overall Length [mm]: 325
• Available as universal article as well, see article no.: 0258986602
• Recommended change interval [km]: 250,000
• Name: LAMBDA ANDUR
• Manufacturer: BOS

• Lambda Sensor: Regulating Probe, Thread pre-greased
• Exhaust System: for pre-catalytic converter
• Line insulation design: with silicone-coated woven-fibre insulation
• for OE number: 08 55 355
• Length [mm]: 570
• Number of circuits: 4
• Weight [kg]: 0.104
• Manufacturer: VEMO GERMANY

General Information: In the warranty, we always make a distinction between wear parts and vehicle parts. All wear parts are subject to a reduced warranty period and a maximum mileage. Brake components such as brake disks, brake pads, etc. maximum of 1000 km (break-in period). Therefore, warranty claims for brake parts are only reviewed with an installation invoice and a record of the wheel hub run-out measurement, including photos. For brake disks and brake pads, the break-in requirements specified by the vehicle manufacturer must be observed. When replacing brakes, the chassis components must always be checked with regard to clearance and the wheel hub with regard to wobble, and the appropriate documentation must be produced. If the vehicle is no longer in its original condition due to tuning work such as wheel accessories and tracking plates, the entitlement to make warranty claims is lost due to third-party work. The same warranty claims are lost if the vehicle is used for motor sports or similar events.

• Engine Number to: 19KP7461
• Lambda Sensor: Regulating Probe
• Length [mm]: 570
• Technical Information Number: Universal 77015
• Fitting Position: before catalytic converter
• Manufacturer: FAE

• Engine Number from: 19KP7462
• Lambda Sensor: Diagnostic Probe
• Length [mm]: 350
• Technical Information Number: Universal 77015
• Manufacturer: FAE

• Lambda Sensor: Regulating Probe
• Fitting Position: before catalytic converter
• Required quantity: 1
• Cable Length [mm]: 350
• Number of pins: 4
• Assy./disassy. by qualified personnel required!:
• Name: Lambda andur
• Manufacturer: HEL

Brief Information: *** HELLA Electronics OE competence for over 60 years.

• for OE number: 855528, 855429
• Exhaust System: for pre-catalytic converter
• Quality: OE
• Manufacturer Restriction: DENSO
• Thread Size: M18x1.5
• Cable Length [mm]: 575
• Number of pins: 4
• Weight [g]: 86
• Gross Weight [g]: 119
• Manufacturer: DENSO

Lambda Sensor: Regulating Probe, Heated, Planar probe, Thread pre-greased, Lambda Sensor Additional information: "Tootja: DENSO
CORSA C (F08, F68),
(kvaliteediklass: Q)" Lisainfo: "Tootja: DENSO
CORSA C (F08, F68),
(kvaliteediklass: Q)"

• for OE number: 93186115
• Quality: OE
• Manufacturer Restriction: DENSO
• Thread Size: M18x1.5
• Cable Length [mm]: 400
• Number of pins: 4
• Weight [g]: 83
• Gross Weight [g]: 116
• Manufacturer: DENSO
• Name: DN DOX-2050

Lambda Sensor: Diagnostic Probe, Heated, Planar probe, Thread pre-greased, Lambda Sensor Additional information: "Tootja: DENSO
CORSA D, 07.06-
(kvaliteediklass: Q)" Lisainfo: "Tootja: DENSO
CORSA D, 07.06-
(kvaliteediklass: Q)"

• Transmission Type: Manual Transmission
• Lambda Sensor: Diagnostic Probe
• Fitting Position: after catalytic converter
• Length [mm]: 575
• Number of circuits: 4
• Manufacturer: VDO

• Lambda Sensor: Regulating Probe
• Length [mm]: 450
• Technical Information Number: Universal 77015
• Fitting Position: before catalytic converter
• Manufacturer: FAE

• Fitting Position: Front, Lower, before catalytic converter
• Lambda Sensor: Regulating Probe, Planar probe, Heated
• Cable Length [mm]: 325
• Name: DE ES21083-12B1
• Manufacturer: DELPHI